Search

How to use total dissolved solids measurements to evaluate the performance of diffuser washers—A mill study, TAPPI Journal April 2020

ABSTRACT: Various types of pulp washing equipment are available. Each washing device has a unique mechanical construction, and the washing principle is often a combination of dilution, thickening, and displacement washing. In this work, the performance of the pressure diffuser washer is studied. In stepwise trials, the effect of the feed and discharge consistencies on the performance of the diffuser was studied. The effect of the downward velocity of the screen on the pressure diffuser’s washing efficiency was also studied. The measurement of total dissolved solids (TDS) by a process refractometer was used as a wash loss measurement unit and the refractometer’s results were used in the calculations of standardized Nordén efficiency (E10) values. The chemical oxygen demand (COD) and conductivity values were also measured and their results compared to the TDS results.The results indicated that feed consistency has a significant effect on the performance and effectiveness of the diffuser washers in the mill. It can also be stated that when the downward velocity of the screen is adjusted to too high a level, the washing efficiency of the pressure diffuser decreases. As a conclusion from the mill tests, it can be stated that even small process parameter changes can provide enhanced diffuser washing at the beginning of the washing line, which has a direct effect on the performance of post-oxygen washing.

Viscoelastic web curl due to storage in wound rolls, TAPPI Journal July 2020

ABSTRACT: Winding is often the final operation in a roll-to-roll manufacturing process. Web materials, i.e., materials that are thin compared to their length, are wound into rolls because this form is the only practical means to store them. The resulting bending strains and associated stresses are large for thick webs and laminates. As many webs are viscoelastic on some time scale, bending stresses lead to creep and inhomogeneous changes in length. When the web material is unwound and cut into discrete samples, a residual curvature remains. This curvature, called curl, is the inability for the web to lie flat at no tension. Curl is an undesirable web defect that causes loss of productivity in a subsequent web process. This paper describes the development and implementation of modeling and experimental tools to explore and mitigate curl in homogenous webs. Two theoretical and numerical methods that allow the prediction of curl in a web are developed: a winding software based on bending recovery theory, and the implementation of dynamic simula-tions of winding. One experimental method is developed that directly measures the curl online by taking advantage of the anticlastic bending resulting from the curl. These methods are demonstrated for a low-density polyethylene web.

New Test Method for Scale Removal and Development of Digester Scale Inhibitors, 2013 PEERS Conference

New Test Method for Scale Removal and Development of Digester Scale Inhibitors, 2013 PEERS Conference

On the Modeling and Characterization of the Tensile Response of Paper, TAPPICon24

Role of xylan in softwood kraft pulp fiber sheets and fiber foams, TAPPICon24

Development of reinforced paper and mitigation of the challenges of raw material availability by utilizing Areca nut leaf, TAPPI Journal September 2022

ABSTRACT: Paper industries are facing a raw material crisis and searching for alternate raw materials that may be able to help mitigate the issue. Many industries use agro-waste as a raw material, irrespective of it having low bleachability and poor mechanical strength. Areca nut leaf (ANL) is a nonwood-based material that may be acceptable as an alternate source of raw material that contains 61.5% holocellulose and 13.6% lignin, which is comparable to other agro-wastes and hardwood pulps. Kraft anthraquinone pulping with 20% active alkali as sodium oxide (Na2O), 25% sulfidity, and 0.05% anthraquinone produced 15 kappa pulps with about 38.5% pulping yield. The bleachability of ANL pulp was good, and 83.5% ISO brightness could be achieved using the D0(EOP)D1 bleaching sequence. The ANL fiber has 33.8% better tensile, 54.5% better tear, and 15.2% better burst index than hardwood fiber. Similarly, 60.4% better tensile, 56.5% better tear, and 21.7% better burst index were observed in ANL than in wheat straw. Thus, the study revealed that Areca nut leaf can be used as an alternative raw material for papermaking, as well as to improve the physical property of paper products by blending it with inferior quality pulp.

MULTI-FUNCTIONAL BARRIER COATING SYSTEMS CREATED BY MULTI-LAYER CURTAIN COATING, TAPPICon 2023

Amphoteric Dry Strength Chemistry Approach to Deal with Low-Quality Fiber and Difficult Wet-end Chemistry Conditions in the Asian and North American Markets, TAPPICon 2023

Continuous Batch Fiber Recovery - An Economical Alternative, 1995 Recycling Symposium Proceedings

Continuous Batch Fiber Recovery - An Economical Alternative, 1995 Recycling Symposium Proceedings

Electrically Switched Ion Exchange (ESIX), A New Approach to Managing Potassium Levels in Pulp Mills with Increased Water Recycle, 1998 Pulping Conference Proceedings

Electrically Switched Ion Exchange (ESIX), A New Approach to Managing Potassium Levels in Pulp Mills with Increased Water Recycle, 1998 Pulping Conference Proceedings