Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Trema guineensis: an appropriate tropical hardwood for pulp and paper production, TAPPI JOURNAL January 1989
Trema guineensis: an appropriate tropical hardwood for pulp and paper production, TAPPI JOURNAL January 1989
Journal articles
Improving anaerobic conversion of pulp mill secondary sludge to biogas by pretreatment, TAPPI JOURNAL June 2010
Improving anaerobic conversion of pulp mill secondary sludge to biogas by pretreatment, TAPPI JOURNAL June 2010
Journal articles
Converted bleach sequence improves pulp quality, TAPPI JOURNAL, July 1990, Vol. 73(7)
Converted bleach sequence improves pulp quality, TAPPI JOURNAL, July 1990, Vol. 73(7)
Journal articles
A new wet-end control system with on-line sensors, TAPPI JOURNAL, July 1990, Vol. 73(7)
A new wet-end control system with on-line sensors, TAPPI JOURNAL, July 1990, Vol. 73(7)
Journal articles
Pulping of southern pine under low water, alkaline conditions using supercritical carbon dioxide-sulfur dioxide mixtures, TAPPI JOURNAL, July 1990, Vol. 73(7)
Pulping of southern pine under low water, alkaline conditions using supercritical carbon dioxide-sulfur dioxide mixtures, TAPPI JOURNAL, July 1990, Vol. 73(7)
Journal articles
Hydrogen-peroxide-reinforced oxygen delignification of southern pine kraft pulp and short sequence bleaching, TAPPI JOURNAL, July 1990, Vol. 73(7)
Hydrogen-peroxide-reinforced oxygen delignification of southern pine kraft pulp and short sequence bleaching, TAPPI JOURNAL, July 1990, Vol. 73(7)
Journal articles
Magazine articles
Recovery boiler back-end heat recovery, TAPPI Journal March 2023
ABSTRACT: Sustainability and efficient use of resources are becoming increasingly important aspects in the operation of all industries. Recently, some biomass-fired boilers have been equipped with increasingly complex condensing back-end heat recovery solutions, sometimes also using heat pumps to upgrade the low-grade heat. In kraft recovery boilers, however, scrubbers are still mainly for gas cleaning, with only simple heat recovery solutions. In this paper, we use process simulation software to study the potential to improve the power generation and energy efficiency by applying condensing back-end heat recovery on a recovery boiler. Different configurations are considered, including heat pumps. Potential streams to serve as heat sinks are considered and evaluated. Lowering the recovery boiler flue gas temperature to approximately 65°C significantly decreases the flue gas losses. The heat can be recovered as hot water, which is used to partially replace low-pressure (LP) steam, making more steam available for the condensing steam turbine portion for increased power generation. The results indicate that in a simple condensing plant, some 1%•4% additional electricity could be generated. In a Nordic mill that provides district heating, even more additional electricity generation, up to 6%, could be achieved. Provided the availability of sufficient low-temperature heat sinks to use the recovered heat, as well as sufficient condensing turbine swallowing capacity to utilize the LP steam, the use of scrubbing and possibly upgrading the heat using heat pumps appears potentially useful.
Journal articles
Magazine articles
Non-process elements in the recovery cycle of six Finnish kraft pulp mills, TAPPI Journal March 2023
ABSTRACT: In this work, the aim was to study the distribution and accumulation of the non-process elements (NPEs) in the recovery cycle of Finnish pulp mills and look at whether the geographical location (North vs. South) correlates with the current Finnish NPE levels. In addition, a comparison to older similar Finnish measurements was made with an attempt to analyze the reasons behind differences in the most typical non-process elements, aluminum (Al), silicon (Si), calcium (Ca), phosphorus (P), magnesium (Mg), manganese (Mn), chlorine (Cl), and potassium (K), taking into account the main elements in the white liquor, sodium (Na) and sulfur (S). The extensive laboratory results gained in this study are from seven sampling points at six pulp mills and present analytical data of metal concentrations. The data obtained presents an update to previous NPE studies. The levels found did not statistically differ between North and South Finland. The NPE levels, apart from phosphorus, found in Finnish pulp mills today have not changed considerably compared to the levels in earlier investigations in the 1990s. In the newest data, the phosphorus concentration was consistently higher in the as fired black liquor, electrostatic precipitator (ESP) ash, lime mud, and green liquor than in the previous results. In addition, the levels of Al, Si, Ca, P, and Mg in recovery boiler ESP ash were consistently higher compared to the older results. As the mills start to close their systems more, a stronger accumulation of NPEs can be expected, increasing the likelihood of more operational problems in the process. Further understanding of where the NPEs accumulate and how they can be most effectively removed will be valuable knowledge in the future.
Journal articles
Developing a New Paradigm for Linerboard Fillers, TAPPI JOURNAL March 2008
Developing a New Paradigm for Linerboard Fillers, TAPPI JOURNAL March 2008
Journal articles
Data driven modeling to reduce fossil fuel consumption in a lime kiln integrated with biomass gasifier, TAPPI Journal September 2026
ABSTRACT: Biomass gasification, although already known and applied, is currently being consolidated as a sustainable alternative in the pulp industry, contributing to the reduction of fossil carbon dioxide (CO2) emissions and to the utilization of forest residues. In this context, pulp mills are beginning to adopt biomass gasification within their chemical recovery cycles by integrating the technology with lime kilns. However, further process studies are still needed to support and optimize this application. Thus, the present study aimed to analyze lime mud feed temperature by applying an artificial neural network model to a gasification system integrated with a lime kiln. For this evaluation, 10 periods of system stability throughout 2024 were selected under different operational conditions. Data from 28 potential predictive variables were collected, a total of 348 observations. This dataset was then processed using R software, where data treatment and model dimensionality reduction were performed, resulting in 10 predictive variables between gasifier and kiln. Next, the dataset was randomly divided into training (70% of the observations) and testing data. The established neural network model (using “neuralnet” package) was optimized, resulting in a configuration containing one hidden layer with three neurons. This setup enabled optimal estimation of the flue gas kiln outlet temperature, with mean absolute error (MAE) = 3.0°C and root mean square error (RMSE) = 4.1°C, applying the resilient backpropagation algorithm with backtracking — both below the thermocouple’s measurement error (±5.0°C) for the evaluated average temperature range (668.2°C). When the same dataset was modeled using the resilient backpropagation algorithm without backtracking, even better results were achieved: MAE = 2.5°C and RMSE = 3.7°C. Thus, after evaluating these and other configurations, it was concluded that the best model required 10 predictive variables and the backpropagation algorithm without backtracking to determine flue gas kiln outlet temperature. These results provide a better understanding of how gasifier and kiln variables influence the temperature in the lime kiln, which is essential to improve control and optimize the calcination process, avoiding supplementary fossil fuel consumption.