Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Effects of different soda loss measurement techniques on brownstock quality, TAPPI Journal July 2024
ABSTRACT: The efficiency of the kraft recovery plant, bleaching process, and paper machine are affected when black liquor carryover from the brownstock washers is not controlled well. Measuring soda loss within a mill can vary from using conductivity, either in-situ or with a lab sample of black liquor filtrate squeezed from the last stage washer, to measuring absolute sodium content with a lab sodium specific ion probe or spectrophotometer. While measuring conductivity has value in tracking trends in black liquor losses, it is not an acceptable method in reporting losses in absolute units, typically in lb/ton of pulp. This is further complicated when trying to benchmark soda loss performance across a fleet of mills with multiple washer lines. Not only do the testing methods vary, but the amount of bound soda on high kappa pulps can be significant. This variability creates inconsistent results, and studies are needed to understand the effect of different testing methods on the pulp quality. In this study, soda loss is expressed as sodium sulfate (Na2SO4). Four different methods to measure soda content in pulp off commercial brownstock washers were studied: full digestion (FD), washing soaking overnight and washing (WSW), soaking in boiling water and stirring 10-min (SW-10), and squeeze-no wash (Sq). Total, washable, and bound sodium sulfate calculations were determined for each soda content measuring technique using inductively coupled plasma-optical emission spectroscopy (ICP-OES). Results showed bound and washable sodium sulfate amounts significantly depend on which soda measurement technique was used. In addition, the soda results were correlated with the pulp kappa numbers. As the kappa number increases, bound soda increases, regardless of the soda measurement method used. Impacts of high sodium sulfate in brownstock are also discussed.
Journal articles
Magazine articles
Editorial: Special pulping and engineering issues of TAPPI Journal yield important recovery cycle research, TAPPI Journal June 2024
ABSTRACT: The June issue of TAPPI Journal, which is dominated by recovery cycle topics, is the last PEERS issue organized by Dr. Peter Hart, the fomer editor-in-chief who passed away this past May. Peter, who was heavily involved with TAPPI’s Pulp Manufacture Division and various pulping-related committees, also started working with conference technical program planning starting in 2005 with the Engineering, Pulping and Environmental (EPE) Conference, which was the precursor to the more recent Pulping, Engineering, Environmental, Recycling and Sustainability (PEERS) Conference. He was also involved with other conference planning, including that for the International Pulp Bleaching Conference. In addition, Peter was a yearly attendee of such conferences starting as far back as 1990.
Journal articles
Magazine articles
A new and quick testing method for evaluating commercial OCC recycled pulp, TAPPI Journal July 2024
ABSTRACT: In this paper, a new and quick testing method for evaluating commercial old corrugated cardboard/containers (OCC) pulp was developed and used by a large Chinese boxboard manufacturer for quality control of imported OCC pulp.
Journal articles
Hydrogen peroxide and caustic soda: Dancing with a dragon while bleaching,TAPPI Journal December 2024
Peter W. Hart, Carl Houtman, and Kilby Hirth | TAPPI J. 12(7): 59(2013) - ABSTRACT: When hydrogen peroxide is mixed with caustic soda, an auto-accelerating reaction can lead to generation of significant amounts of heat and oxygen. On the basis of experiments using typical pulp mill process concentration and temperatures, a relatively simple kinetic model has been developed. Evaluation of these model results reveals that hydrogen peroxide-caustic soda systems are extremely sensitive to hydrogen peroxide:caustic soda ratio, transition metal contamination, and temperature. Small changes in initial conditions can result in a closed system becoming explosive. Analysis of model results was used to develop guidelines for safer application of hydrogen peroxide in a mill setting.
Journal articles
Production of high yield bleached hardwood kraft pulp: Breaking the kraft pulp yield barrier,TAPPI Journal December 2024
Author: Peter W. Hart | TAPPI J. 10(9): 37(2011) - ABSTRACT: A modified kraft pulping process has been developed that successfully breaks the traditional hard-wood kraft pulp yield barrier. The process produces fully bleached, high brightness hardwood kraft pulp with a yield of greater than 53% on wood. Details of the development and processing steps, along with various recovery cycle impacts, are discussed.
Journal articles
The effect of Stachys floridana Shuttlew.ex Benth extract as an additive on the chemical properties of chitosan biodegradable film, TAPPI Journal June 2025
ABSTRACT: The purpose of this study is to explore chitosan with Stachys floridana Shuttlew. ex Benth (SFSB) extract as an additive to prepare an active film. The effects of the SFSB extract on the physical, antioxidant, and bacteriostatic properties of chitosan biodegradable films were studied. The results showed that the addition of SFSB extract significantly improved the antioxidant and antibacterial properties of the film, and its biodegradation rate increased rapidly. Compared to the control film, the water solubility was lower at 19.40%, the expansion degree was higher at 288.90%, the water vapor permeability (WVP) was 0.364 g·mm/(m²·d·kPa), the surface hydrophobicity increased, and the mechanical strength was also improved. The contact angle increased to 89.3°. In addition, as the amount of SFSB increased, the thermal stability of chitosan-Stachys floridana Shuttlew. ex Benth (CS-SFSB) films also increased significantly, and their ultraviolet (UV) blocking ability was gradually enhanced. The results indicate that CS-SFSB has potential as a food packaging material.
Journal articles
Gap mechanics in pulp refiners, TAPPI Journal June 2025
ABSTRACT: Studies of pulp refining have shown that a single bar impact on pulp has only a 1%•5% probability of producing a successful refining effect. This study has explored the reason why. An analysis of refining kinetics suggested that small segments of a fiber length, about a fiber diameter in size, are treated during each impact. Measurements of localized swelling along fiber lengths caused by refining supported this finding. Based on these findings, it was postulated that force transmittal through fiber networks occurred primarily at fiber crossings. The small size of fiber diameters relative to fiber lengths accounts for the low probability of a successful refining event at each impact. This probability, and the probability of fibers being captured and impacted during passage through a refiner, account for the need for multiple bar crossings to refine pulps.
Journal articles
Extended usage of xylanase enzyme to enhance the bleaching of softwood kraft pulp, TAPPI JOURNAL, January 2006
Extended usage of xylanase enzyme to enhance the bleaching of softwood kraft pulp, TAPPI JOURNAL, January 2006, Vol. 5(1) (164 KB)
Journal articles
Comparative annual cost efficiency between thermal and chemical oxidation of TRS in kraft mills, TAPPI JOURNAL, July 2005, Vol. 4(7) (200 KB)
Comparative annual cost efficiency between thermal and chemical oxidation of TRS in kraft mills, TAPPI JOURNAL, July 2005, Vol. 4(7) (200 KB)
Journal articles
Conversion of paper-grade pulp from rice straw into dissolving pulp, TAPPI Journal June 2025
ABSTRACT: About 1,165 million metric tons of rice straw is generated every year worldwide, which can be a good source for the circular bioeconomy. In this research paper, the paper-grade pulp from rice straw was converted to dissolving-grade pulp by fractionation in a biorefinery initiative. Rice straw was cooked at an optimum condition of 8% potassium hydroxide (KOH) charge for 120 min at 150°C and produced a pulp yield of 47.2% with a kappa number of 18.5. Subsequently, D0(EP)D1 bleaching was carried out for the produced pulp, and the brightness of the pulp reached to 82.4%. From the black liquor, 16.5% of the lignin and 11.9% of the hemicellulose were isolated for producing biobased products and chemicals, and then the spent liquor was used for soil amendment. The bleached pulp was fractionated in a Bauer McNett fiber classifier. The pulp fibers retained on 16-, 30-, and 50-mesh screens were used as a longer fiber fraction pulp, and pulp fibers retained on 100- and 200-mesh screens were used as a shorter fiber pulp. The longer and shorter fiber fraction pulps were analyzed for cellulose, R10, pentosan, and viscosity. The long fiber fraction pulps were characterized by higher cellulose (88.2% vs. 83.1%) and lower pentosan (11.3% vs. 13.0%) content than the shorter fiber fraction pulps. The longer fiber fraction was further treated with cold KOH to remove residual hemicellulose. The KOH extraction reduced pentosan content in pulp to 6.3% and increased á-cellulose content to 91.3%. The short fiber fraction was converted to monomeric sugars using cellulase enzymes with varying reaction time, temperature, and consistency. The efficiency of cellulase activity was assessed through glucose yield and residual dry weight. A temperature of 45°C, 5.0 pH, 5% consistency, and 6 filter paper units/gram (FPU/g) o.d. pulp resulted in maximum sugar conversion of 85.7%.