Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Biomass gasification for green ammonia production in kraft mills, TAPPI Journal September 2026
ABSTRACT: As the global energy sector transitions toward net-zero emissions, kraft pulp mills present a compelling opportunity to produce green fuels and achieve net-negative emissions by capturing biogenic carbon, helping offset hard-to-abate sectors. This study explores the techno-economics of integrating biomass gasification for green ammonia production within kraft mills, using KraftSIM modeling to evaluate ammonia production, steam balance, emissions, and utility impacts. The proposed design enables energy and water system integration with the existing mill and allows for a gradual scale-up without disrupting the chemistry and operation of the recovery cycle. Across five scenarios representing different biomass gasification rates ranging from 100 to 1000 bone-dry metric tons per day (BDMT/d), the process yields ammonia at approximately 0.51 metric tons per bone-dry metric ton (t/ BDMT), while generating significant low- and medium-pressure steam and hot water that offset mill utility demands. The incineration of pressure swing adsorption tail gas and ammonia plant purge gas in the power boiler reduces biomass combustion and enhances power boiler efficiency. Economic analysis suggests a net revenue potential of approximately CA$380/BDMT, which could increase with the implementation of biogenic carbon pricing. Overall profitability is strongly influenced by biomass procurement costs, electricity prices, and prevailing green fuel and chemical market premium. This work outlines a practical, near-term decarbonization pathway for kraft mills by coupling green fuel production with potential opportunities for carbon removal.
Journal articles
Effects of calcium on sodium salt scaling with the presence of resin acids and fatty acids, TAPPI Journal June 2026
ABSTRACT: Reintroducing tall oil soap or its related products into high dry solids black liquor has been found to reduce sodium salt scaling in falling film evaporators. Aside from resin acids and fatty acids, which are the likely scale inhibitors, calcium is reintroduced into black liquor because of the relatively high calcium content of tall oil soap. One concern is that this increase in calcium content might lead to the formation of additional calcium and sodium scales in evaporators. In this work, we investigated the relationship among trace amounts of calcium, sodium salts, resin acids, and fatty acids in a controlled system using a model salt solution and a benchtop setup. We studied the effects of the calcium carbonate addition and calcium carbonate scales on sodium salt scaling in the presence of resin acids and fatty acids. We found that some calcium carbonate is incorporated in the precipitated sodium crystals, and the suspended sodium crystals become larger and more compact with increasing calcium carbonate concentration. Experiments in the benchtop setup show that precipitating calcium carbonate scale on the heat exchanger does not lead to a higher rate of sodium salt scaling. The solubility of calcium carbonate is not affected by the addition of resin acids and fatty acids. These findings indicate that the reduction in sodium salt scaling through the addition of tall oil soap is primarily related to resin acids and fatty acids, rather than to calcium or to interactions between calcium and mixtures of resin and fatty acids.
Journal articles
Preparation of a vegan leather from mycelium with papermaking method, TAPPI Journal June 2026
ABSTRACT: With growing concern over the environmental impacts of both natural leather and conventional synthetic leathers, the development of sustainable and eco-friendly leather alternatives has become an urgent research priority. In this study, an innovative wet papermaking strategy is proposed to fabricate continuous, homogeneous mycelial sheets from chitin-rich fungal mycelium, mimicking the matrix structure of genuine leather. These mycelial sheets were chemically modified to meet the performance requirements of leather foam layers. Subsequently, the modified mycelial sheets were combined with a substrate fabric to produce a novel mycelium-based leather composite (myco-paper leather) that achieves an excellent balance of mechanical properties and tactile qualities. Experimental results demonstrate that the mycelium-sheet-based leather substitute exhibits remarkable mechanical performance, with a tensile strength of approximately 45 MPa and an elongation at break of about 10.5%. After lamination with the substrate fabric, the composite material shows a tear strength of approximately 16 N, along with a desirable hand feel and surface texture. Following tannic acid tanning, the mycelial sheets also exhibit significant antimicrobial and antifungal properties, forming an inhibition zone of approximately 2 mm against Staphylococcus aureus. Through reinforcement with plant fibers, the developed material attains both strength and flexibility, indicating that the wet papermaking of mycelial sheets is a feasible and scalable approach for producing sustainable leather alternatives. This work not only employs a simple and mature papermaking process to process fungal mycelium but also provides a new conceptual and practical foundation for the large-scale production of bio-based leather substitutes. The findings have significant implications for advancing a low-carbon, sustainable leather industry.
Journal articles
Investigation of the factors contributing to malodorous gases emission during secondary fiber reuse, TAPPI Journal June 2026
ABSTRACT: Malodorous gases are commonly produced during secondary fiber reuse, which is harmful to human health and causes environmental pollution. This paper investigated the influence of fiber type and concentration, temperature, and whitewater concentration on the malodorous gases. The results indicated that, in pulp prepared with fresh water, bleached hardwood kraft pulp (LBKP) did not produce malodorous gases after standing for five days. In contrast, the secondary fiber began to release substantial amounts of total volatile organic compounds (TVOC) on the third day and hydrogen sulfide (H2S) and ammonia (NH3) on the sixth day, and black substances began to appear in the pulp, which proved that the microorganisms began to proliferate. With the increase of the secondary fiber concentration, the release amounts of TVOC, H2S, and NH3 gradually rose, along with the black substances in the pulp. With increased temperature, the release of TVOC increased steadily, while the release of H2S and NH3 reached the maximum at about 45°C, and then began to decline. The decrease of the pulp freeness accelerated the generation of the malodorous gases, but the total release amounts of TVOC, H2S, and NH3 were basically the same. With the increase of white water concentration, the release of TVOC, H2S, and NH3 increased rapidly. When the white water/fresh water was 20 mL/80 mL, the slurry changed from pale yellow to aterrimus on the sixth day. Therefore, microorganisms in the secondary fiber caused pulp deterioration, while white water was the main reason for generating a large amount of malodorous gases.
Journal articles
Optimization of energy efficiency and condensate production in evaporation plants for a modern softwood pulp mill, TAPPI Journal April 2026
ABSTRACT: To meet the need to further improve thermal efficiency and environmental performance of kraft pulp mills, new systems and techniques have been developed within the evaporation plant. This paper describes these novel approaches and how they were implemented in a project completed in 2018 for a new evaporator and condensate treatment system supplied by Valmet at the SCA Östrand market pulp mill in Sweden. This project was part of a stepwise upgrade of the complete mill to increase the production capacity of the mill from 430,000 to 900,000 air-dried metric tons/year (ADt/y). As part of this upgrade, the mill had the objectives to increase the energy efficiency of the pulp mill and to minimize the air emissions as much as possible, the effluent volume, and the water usage in the mill. The mill also wanted to have the disposal of the biosludge in the black liquor, and the production of tall oil from black liquor soap, liquid methanol, and turpentine. This required that the new evaporation and condensate treatment system be very closely integrated into the other process departments of the mill, including integration of the hot weak black liquor flash vapor from the digester directly into the evaporator train and the production of multiple streams of clean evaporation plant condensate at the correct temperature for the bleach plant. Heat and mass balance calculation values, which were found to do very well in predicting the effect on actual mill operation, are also presented in this paper.
Journal articles
Effect of pulp refining on thixotropy of cellulose fiber suspensions, TAPPI Journal September 2025
ABSTRACT: This paper presents results on the thixotropic behavior of low-consistency bleached eucalyptus fiber suspensions that had been mechanically treated. The pulps were refined in a PFI mill at different numbers of revolutions (0, 3000, and 6000) to study the effect of refining intensity on the viscosity time-response of fiber suspensions. In steady rheological tests, all the suspensions exhibited shear thinning behavior and no significant differences were observed after mechanical treatment. Stepwise experiments showed that viscosity continuously increased with time when shear rate was suddenly reduced. Additionally, a delay in time evolution of viscosity was observed as the pulp was more refined. A stretched exponential model was fitted to the experimental results of viscosity.
Journal articles
Assessing lignin content in Nordic hardwood and softwood species using models based on near-infrared (NIR) spectral data and partial least squares regression (PLSR), TAPPI Journal September 2025
ABSTRACT: Continuous kraft cooking digesters face challenges affecting product quality, making it valuable to improve control through advanced techniques like near-infrared (NIR) spectroscopy, model predictive control, and machine learning models. The primary goal of this study was to use NIR spectra to predict the amount of lignin in hardwood and softwood samples. This study investigated the correlation of NIR derivative spectra with the amounts of lignin relative to other constituents, namely cellulose, hemicellulose, and water, in wood chip samples of varying chip sizes and shapes from six Nordic wood species. It employed partial least squares regression (PLSR) on the NIR data to construct a model that predicted the lignin fraction and the relative fraction of acid-soluble lignin. When trained on a group of five wood species, the model achieved a satisfactory predictive ability, striking a balance between a wide range of lignin content and a consistent chemical environment. The accuracy increased further when the model was restricted only to spruce and pine, reflecting the benefits of a more homogenous dataset. Additionally, the optimal number of latent variables was identified as two, indicating that three distinct chemical components — cellulose, lignin and water — can be effectively differentiated using NIR.
Journal articles
Toward environmental resilience in pulp and paper manufacturing: Water consumption and carbon dioxide emission reductions, TAPPI Journal September 2025
ABSTRACT: Pulp and paper manufacturing is a water- and energy-intensive industrial sector, necessitating improvement of its operational efficiency, as well as reduction of emissions to the maximum extent possible. This review focuses on the reduction of water consumption and carbon dioxide (CO2) emissions that originate in the pulp and paper industry (PPI). First, process simulation and optimization techniques used for water consumption reduction are reviewed. Then, techno-economic analyses of solvent-based CO2 capture from PPI are discussed. Additionally, key actions are proposed for enhancing water consumption reduction and CO2 capture in PPI.
Journal articles
Materials performance considerations in hydrothermal liquefaction conversion of biomass, TAPPI Journal June 2025
ABSTRACT: Hydrothermal liquefaction (HTL) is a promising thermochemical route developed to convert woody biomass and biowaste to biochemicals and bio-oils. However, the operating conditions are rather harsh to biorefinery structural metallic components. These conditions include alkaline catalysts such as potassium carbonate (K2CO3); hot, pressurized (sub-critical) water reaction; and medium and aggressive anions chlorine (Cl•) and hydrogen sulfide (H•) released from biomass feedstocks. Thus, selection of suitable structural alloys for biorefinery components involves striking a balance between mechanical properties, corrosion resistance, and cost. Alloys currently being considered for this application include ferritic-martensitic steels and austenitic stainless steels. From a corrosion perspective in hot pressurized water, the former typically exhibits higher stress corrosion cracking resistance, whereas the latter exhibits higher corrosion resistance. This study reviews cost-effective corrosion control strategies aimed at increasing the chromium (Cr) content for protective surface oxide formation, as screened by testing in simulated HTL alkaline water, to support materials selection and design. Corrosion control strategies include surface modification (increasing surface Cr content), alloying (increasing bulk Cr content), and stainless-steel type (ferritic vs. austenitic). Of the alloys considered (including those subjected to surface modification), ferritic stainless steels exhibit a promising balance between corrosion and stress corrosion cracking resistance, adding another family of candidate alloys for structural biorefinery component materials selection and design.
Journal articles
Magazine articles
Understanding the risks and rewards of using 50% vs. 10% strength peroxide in pulp bleach plants,TAPPI Journal December 2024
Authors: Alan W. Rudie and Peter W. Hart | TAPPI J. 17(11): 601(2018) - ABSTRACT: The use of 50% concentration and 10% concentration hydrogen peroxide were evaluated for chemical and mechanical pulp bleach plants at storage and at point of use. Several dangerous occurrences have been documented when the supply of 50% peroxide going into the pulping process was not stopped during a process failure. Startup conditions and leaking block valves during maintenance outages have also contributed to explosions. Although hazardous events have occurred, 50% peroxide can be stored safely with proper precautions and engineering controls. For point of use in a chemical bleach plant, it is recommended to dilute the peroxide to 10% prior to application, because risk does not outweigh the benefit. For point of use in a mechanical bleach plant, it is recommended to use 50% peroxide going into a bleach liquor mixing system that includes the other chemicals used to maintain the brightening reaction rate. When 50% peroxide is used, it is critical that proper engineering controls are used to mitigate any risks.