Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
89APR177
MD microstriations in paper: a two-sided shrinkage phenomenon?, TAPPI JOURNAL April 1989
Journal articles
Electrochemical Removal of Color and Toxicity from Bleached
Electrochemical Removal of Color and Toxicity from Bleached Kraft Effluents, 1994 Environmental Conference Proceedings
Journal articles
Editorial: Special issue on Paper Physics highlights continued focus on packaging, TAPPI Journal August 2025
ABSTRACT: It is a great pleasure to present this special issue of TAPPI Journal, featuring papers from the 2024 International Paper Physics Conference (IPPC) that have been peer-reviewed for publication in this journal. The conference was held in Wuppertal, Germany, from September 30 to October 2, 2024. This IPPC series is one component of the annual meeting of the International Paper Physics Committee and community, complementing the Fundamental Research Symposia established in 1957 — and the Progress in Paper Physics meetings.
Journal articles
A targeted approach to produce energy-efficient packaging materials from high-yield pulp, TAPPI Journal August 2025
ABSTRACT: Unlike fossil-based plastics, wood-based packaging materials can be produced in an ecofriendly manner using wood chip residuals from sawmills and pulpwood. To produce high-yield pulp like chemithermomechanical pulps (CTMPs) for paperboard and liquid packaging, it is crucial to reduce the electric energy consumption during fiber separation. The ultimate objective is to revolutionize paperboard production by achieving a middle-layer CTMP process that consumes less than 200 kilowatt-hours per metric ton (kWh/t), significantly improving from the current 500•600 kWh/t energy demand. Optimizing the CTMP impregnation process of sodium sulfite (Na2SO3) in wood chips is crucial for achieving uniform softening, ideally at the fiber level. The properties of the fibers are significantly affected by the content of lignin sulfonates within the walls of the fiber and the middle lamellae. In this study, we employed in-house developed X-ray fluorescence (XRF) techniques, validated by beamline measurements, to map the distribution of sulfonated lignin within fibers. It also seemed possible to enhance the surface area of lignin-rich pulp fibers while losing minimal bulk by refining them with well-optimized low consistency (LC) refining. We aimed to achieve a highly efficient separation of coniferous wood fibers by co-optimizing the sulfonation and the temperature in the preheater and chip refiner. Additionally, we explored how lignin’s softening behavior and potential crosslinking influence subsequent unit operations, including pressing, peroxide bleaching, and drying, following the defibration process. In defibration during chip refining, the maximum softening of wood fibers is preferred to maximize fiber preservation and minimize energy consumption. However, optimizing the stiffness of finished pulp fibers is preferable to reduce bulk loss during paperboard production. It can strive to optimize processes to develop stronger, lighter, and more sustainable composite packaging materials. Reducing environmental impact and electric energy can help create a more sustainable future.
Journal articles
On the design of corrugated boards: A new FEM modeling and experimental validation, TAPPI Journal August 2025
ABSTRACT: This study presents a simplified finite element modeling (FEM) approach suitable for large structures made of corrugated boards, such as customized packages, based on a homogenization method, which is combined with correction factors for internal mechanisms. The homogenization process reduces computational time by transforming flute geometries into equivalent elastic models. In large deformations and in the presence of contact for a given geometry, the effective elastic modulus in the thickness direction, as well as the effective thickness of the structure, are corrected by two statistical Weibull distributions representing the contact and buckling mechanisms in a corrugated board. The Weibull parameters are obtained via experimental analysis, and such a process is then validated. The results demonstrate that the statistical parameters (â1 = 0.14, â2 = 1.31) can be used for the simplistic representation of corrugated boards, being computationally efficient. This research contributes to the optimization of corrugated packaging design, specifically by simplifying FEM models for faster, yet equally accurate, simulations.
Journal articles
Reinforcing folding boxboard ply stock with refined pulp and its effect on dewatering potential, TAPPI Journal February 2025
ABSTRACT: The folding boxboard (FBB) filler ply typically contains a significant amount of mechanical pulp such as bleached thermomechanical pulp (BTMP), bleached chemi-thermomechanical pulp (BCTMP), and chemi-thermomechanical pulp (CTMP), etc. It is usually reinforced with either refined broke from the same paper machine line and converting process or by utilizing traditional bleached kraft pulp (BKP). In response to the drive for improved/increased ply bond (to avoid undesired delamination), increased bulk, reduced basis weight, and minimized energy consumption, papermakers have experimented with various options and strategies. In between the common approaches, choices have been made between reducing the refining of the mechanical pulp, increasing the broke refining (more frequently practiced on the production scale), or increasing the BKP refining (a potentially superior choice). This study focused on a simplified approach to assess the impact of three reinforcement pulps with different refining levels on the dewatering of the filler ply. The reinforcement pulp was added to the core stock for the FBB filler ply — a mechanical pulp, BCTMP, with a drainability of 25 °SR. The proportions of the reinforcement pulp, hardwood bleached kraft pulp (HWBKP), were 20% of 30-35 °SR, 10% of HWBKP 50-55 °SR, and 5% of HWBKP 70-75 °SR. The intention behind using varying percentages of reinforcement pulp was to attain a controlled internal bond while enhancing bulk through increased mechanical pulp content. The dewatering potential of the stock mixtures was assessed at three vacuum levels — 4, 10, and 25 kPa — that can be found in progressive stages within production- scale forming sections. Our goal was to find an optimal reinforcement strategy for filler ply that would minimize the use of the reinforcement pulp, give better strength, retain bulk, and lower basis weight. The success of this strategy was verified with an actual FBB machine.
Journal articles
Filtration performance of face masks and facepiece respirators used during COVID-19 pandemic, TAPPI Journal February 2025
ABSTRACT: The rapid spread of SARS-CoV-2 has created challenges for societies, healthcare settings, businesses, and institutions. To curb virus transmission, various measures like lockdown, social distancing, hand hygiene, and using appropriate personal protective equipment (PPEs), including face masks, have been recommended. Face masks and facepiece respirators are considered to act as barriers against microbial transmission from person to person. In this study, we selected barrier materials used during the COVID-19 pandemic that included four non-medical face masks and three facepiece respirators. Facepiece respirators were distributed by the U.S. Administration through pharmacy outlets. Results showed that facepiece respirator R95 has the highest filtration efficiency (above 99%), which remains more or less the same over different particle sizes. The N95 respirator’s filtration efficiency was lower than that of R95, but its barrier resistance was lower than that of the R95, indicating that it can be comfortably used over longer duration. Face masks were evaluated using ASTM F 3502-24 for their barrier performance. At 0.1 and 0.3 ìm particle size, domestically manufactured masks met the standard for higher performance. Interestingly, the results indicate that quality of raw materials and manufacturing standards play important roles, as is evident in domestically manufactured face mask and facepiece respirators.
Journal articles
Comparison of the application of polysaccharide-based barrier coatings on paper using film press and spray coating, TAPPI Journal January 2025
The growing demand for sustainable packaging has spurred research into biopolymer-based solutions and their application to paper substrates. This study compares the application of low solids, high viscous aqueous solutions of alginate and chitosan on two different paper substrates using a laboratory film press coater and a purpose-built spray coating unit, with a focus on barrier performance and practical industry considerations. Key parameters investigated are air flow rate, water vapor transmission rate, and grease resistance. Results showed that due to the low solids content of the applied biopolymer solutions, film press coating required a double-layer application for coat weights exceeding 4 g/m², making it less viable for industrial application. In contrast, spray coating allowed for higher application weights in a single step. The barrier properties of spray coated samples, compared to film press coatings, varied with the paper substrate: spray coating performed better on one substrate and worse on the other. Contact angle measurement of the substrates suggested that spray coating is more suitable for a more hydrophilic substrate because of improved surface wetting. The study also identified issues with drying conditions and pinholes affecting the quality of spray coated samples, indicating a need for further research to optimize these parameters.
Journal articles
Water-based adhesive penetration into paperboard and coated paperboard, TAPPI Journal January 2025
The setting of water-based adhesives in contact with paperboard is important in the production of boxes and other packaging, but the topic has received little attention in the literature. The penetration of the adhesive into the paper surface is important to get good bond strength through mechanical interlocking. The influence of the process conditions and the paper properties on this penetration is lacking. A water-based adhesive was applied to an uncoated and coated paperboard. The coating layer had two latex levels. Samples were characterized in terms of air permeability, void fraction, average pore size, and coat weight. The adhesive was applied to the samples in a mechanical press, squeezing a drop between two samples. The penetration of the adhesive was characterized with a silicone oil absorption method that measured the decrease in pore volume after the adhesive had been applied to approximate the pore volume taken up by the adhesive. The bond strength was measured with a peeling test. The penetration depth into uncoated paper did not depend on the application method parameters such as pressing time, pressure, or initial solids of the adhesive. The penetration depth ranged from 35•40 mm. The penetration into 10 pph latex content coated paper was similar to the uncoated samples, but reduced penetration was observed into the 40 pph latex content coatings. The results were compared to the limiting amount of adhesive that was obtained from the weight gain of the samples and to a simple model that is based on flow in porous media. Peel tests revealed that good penetration was needed, as well as a strong coating layer to obtain high peel forces.
Journal articles
Editorial: Design considerations for developing high-quality flexible packaging laminates, TAPPI Journal July 2025
ABSTRACT: The global flexible packaging industry has constantly evolved by developing new materials, film design, polymer processing techniques, and machinery to overcome challenges posed by consumer demands, regulation, and societal pressure. While achieving superior quality and improved mechanical film attributes has always been the cornerstone for new technical developments in this industry, the end-of life shortcoming for most plastic films has driven the value chain to strive harder to design and develop sustainable packaging structures.