Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Full-scale operation of a membrane-based black liquor concentrator, TAPPI Journal January 2026
ABSTRACT: For years, black liquor concentration by reverse osmosis has been an aspiration for reducing mill energy consumption and costs. Building on a 2023 report of an 81% reduction in the energy intensity for concentrating black liquor using its membrane platform at the pilot scale, this paper reports on the fabrication, installation, startup, and operation of the world’s first full-scale membrane-based black liquor concentration system at the International Paper Grande Prairie mill in Canada. The majority of the membrane modules in this system have reliably exceeded permeability expectations by more than 50%. In addition to strong membrane performance, the system has been a significant source of learnings for material specifications and system design. Incorporating these learnings and comparing to typical multiple effect evaporators, the system demonstrates a 43% reduction in capital cost for the same capacity, a 30% reduction in the lifetime cost of removing water from black liquor, and an 86% reduction in energy use. The impact on washer optimization was also considered, and net energy and chemical costs were reduced by US$3.8 and US$6.8/a.d. metric ton for a typical brown and bleach mill, respectively, when incorporating this technology. Completed in less than 12 months, the facility has demonstrated successful black liquor concentration at the 500 gpm scale with monthly uptime as high as 96%.
Journal articles
Energy and emission implications of optimized white liquor causticity, TAPPI Journal January 2026
ABSTRACT: Optimizing the causticizing plant offers significant opportunities for energy and emissions savings in kraft mills by minimizing the chemical and water deadload introduced into the recovery cycle via white liquor. Modern control strategies utilize both feedforward and feedback loops to manage causticity, enabling more aggressive targets closer to equilibrium levels. This paper evaluates the benefits of optimizing white liquor chemistry through a detailed CADSIM Plus simulation model, replicating the chemistry of a Canadian bleached kraft mill that adopted an automated causticizing control system. The control system increased causticity from 77.0% to 82.3% at a fixed total titratable alkali (TTA) of 126.5 grams of sodium dioxide per liter (gNa2O/L). Modeling this chemistry change indicated a 1.5 metric tons per hour (t/hr) reduction in evaporator steam demand and a 2.8% increase in black liquor higher heating value. Consequently, the improved heating value resulted in a 1.5% rise in recovery boiler steam production and a 5.3% reduction in biomass energy consumption in power boilers, leading to a 4.8% decrease in biogenic carbon dioxide (CO2) emissions. Additionally, reducing the inorganic and water deadload throughout the recovery cycle may support higher as-fired dry solids targets, enhancing recovery boiler energy efficiency by lowering the water evaporation requirement during black liquor combustion. However, implementing a causticizing control system requires careful assessment of potential lime kiln bottlenecks, as increased causticity demands may affect kiln operations depending on broader mill conditions. Overall, an automated causticizing control system enhances process efficiency, reduces energy consumption and emissions, and positions kraft mills for improved productivity and longterm sustainability.
Journal articles
Effects of variability of wood chip composition on recovery cycle operation, TAPPI Journal January 2026
ABSTRACT: Fluctuations in wood chip properties in kraft pulp mills, which often follow seasonal patterns, can lead to changes or disruptions in the operation of the recovery cycle whereby the root causes are not immediately obvious. In some cases, these changes are attributed to operational adjustments in the digester or brownstock washing areas resulting from the variability in wood characteristics. Varying wood chip characteristics that have the most significant impact on the recovery cycle operation include the content of non-process elements (NPEs), extractives, and properties influenced by chip storage conditions. Elevated levels of NPEs, often associated with a higher influx of wood bark into the digester, can negatively affect the entire recovery cycle. Increased levels of chlorine and potassium can lead to severe fouling and corrosion in the recovery boiler. Higher concentrations of silicon, aluminum, phosphorus, magnesium and calcium in the chips may accelerate scaling in the evaporation plant, impair dregs and lime mud settling and filtering, reduce lime mud solids content and lime availability, and increase the amounts of dregs, grits, and purged lime mud. This technical review provides an overview of the most significant effects that changes in wood chip quality can potentially exert on various processes within the kraft recovery cycle.
Journal articles
Non-process elements in the lime cycle: New findings regarding NPE distribution and lime mud filterability, TAPPI Journal July 2026
ABSTRACT: Proper functioning of the recausticizing cycle is crucial for securing a stable white liquor supply for a pulp mill. Common runnability problems in the modern lime cycle, such as low filterability and poor dewatering of lime mud, high dead load, or ring formation in the lime kiln, are often caused by accumulation of non-process elements (NPEs). This project attempted to verify the traditional rules of thumb regarding the chemical behavior of NPEs: magnesium (Mg), aluminum (Al), silicon (Si), phosphorus (P), zinc (Zn), manganese (Mn), iron (Fe), copper (Cu), barium (Ba), cadmium (Cd), and lead (Pb) in the causticizing reaction, and to investigate the reasons behind poor lime mud filterability. First, a standardized method for measuring filterability of lime mud was developed. Next, a series of recausticizing experiments, followed by immediate filtration trials, was conducted using mill green liquors, laboratory-made synthetic green liquor, reburned lime/makeup mix, and extra NPE additions. It was found that sodium (Na), potassium (K), and sulfur (S) followed the liquid phase, as expected, while Mg, P, and Ba, but also Pb, Cu, and Cd, showed low solubility and accumulated in the lime mud. The Si and Al accumulated in the lime mud even though the soluble content in liquor was high, while the behavior of Mn, Fe, and Zn was more complex. Based on these results, tentative solubility limits for NPEs were suggested as a first estimate for the maximum possible concentrations of NPEs in mill white liquor. The causticization-filtration experiments revealed that overliming and high content of Mg in green liquor clearly led to lower filterability, but our addition of Si did not have such an effect. As differences in particle size and size distribution have a certain impact on the filtration resistance, the lime mud sedimentation behavior, combined with other characterization methods, might be used as an indication for the filterability. Finally, a list of recommendations for pulp mills was formulated that starts with establishing a comprehensive standard for a lime mud with good filterability. This standard can be used as a benchmark for comparison any time a lime cycle runnability problem is identified.
Journal articles
Controlling sulfidity by recycling sulfur in CNCG, TAPPI Journal July 2026
ABSTRACT: Pulp and paper mills have faced a major dilemma. On one hand, mills should not dispose of the side streams by mixing them with effluent water. On the other hand, there has been no other way to dispose of excess sulfur than getting rid of recovery boiler electrostatic precipitator (ESP) ash and buying sodium hydroxide to replace lost sodium. A new, yet old, process has been introduced to alleviate the problem. An alternative is the onsite production of sulfuric acid (H2SO4) to significantly reduce, or to even eliminate, the need for recovery boiler fly ash dumping. A sulfuric acid plant produces concentrated commercial quality H2SO4 from concentrated non-condensable gases (CNCGs). Up to 99.9% of the sulfur in CNCGs can be converted into concentrated sulfuric acid with this wet-gas sulfuric acid (WSA) process. There are already references on pulp mills highlighting that the process is straightforward to use. Mills can increase the amount of sulfur in CNCGs by controlling the heavy back liquor storage time and temperature. This opens up a new way to control the mill sulfidity by recycling sulfur. The effect of recycling sulfur is highlighted with reference mills. Due to integrated paper production, the Northern Mill is a large energy consumer, producing mostly softwood-based end products. The Eucalyptus Mill is a large standalone hardwood (eucalyptus) pulp mill where electricity is produced substantially in excess of its own use. As a sample case, lignin production with and without sulfur recycling is presented.
Journal articles
Black liquor spray properties in-furnace conditions for swirl cone nozzles, TAPPI Journal July 2026
ABSTRACT: Recovery boiler furnace operation is controlled for high chemical recovery, high steam production, and low emissions. Good control allows long runs with minimum cleaning without expensive shutdowns. An essential variable affecting boiler operation is black liquor spraying into the furnace. Poorly controlled black liquor spraying causes difficulties, e.g., in chemical recovery, fouling of heat transfer surfaces, and decreased energy production. A challenging measurement strategy with three different swirl cone nozzles . types A, C, and T . was carried out at a mill in the United States. Black liquor spray properties were measured under in-furnace conditions for flow rates of 2.0 L/s to 3.0 L/s. Three spraying temperatures of 119™‹C, 122™‹C, and 126™‹C, which were 2™‹C, 5™‹C, and 9™‹C above the boiling point (ƒ¢Te), were tested. These flow rates and temperatures are typical for industrial nozzle sizes with exit orifice sizes of 17 mm and 22 mm. An imaging method to measure droplet size in a highly challenging furnace environment was developed. Droplet volume median diameter (Dv50) for nozzles A, C, and T varied between 7 mm to 4 mm, 7 mm to 5 mm, and 8 mm to 6 mm, depending on the flow rate and temperature. The high number of droplets detected by the analysis program enabled data fitting into statistical correlations. The size and width parameters for the Rosin™]Rammer droplet size distribution function could be defined. The droplet size distribution was found to be surprisingly wide, probably because of swollen droplets. Spray velocity was measured in two locations, 5 cm from the nozzle and 1.8 m from the nozzle. Near the nozzle, the average velocity increased from 7.3 m/s to 13 m/s when the flow rate was increased from 2 L/s to 3 L/s. Increase of black liquor temperature increased spray velocity in most of the cases. At the distance of 1.8 m from the nozzle, average spray velocities varied between 4.0 m/s to 11 m/s, depending on nozzle geometry, flow rate, and temperature. The opening angles of the spray for nozzles A and C varied between 57™‹ to 78™‹. The opening angle of nozzle T with flow guide varied between 48™‹ to 56™‹. The highest penetration of the spray was estimated for nozzle T because of the narrow spray and large droplets.
Journal articles
Image classification of the furnace bed height in recovery boilers, TAPPI Journal July 2026
ABSTRACT: The goal of this study is to develop an approach for classifying char bed height in a recovery boiler during operation. The resulting classified images form a dataset that can be used by the mill to support operational improvements. The study integrates data from the digester, evaporation plant, recovery boiler, and recausticizing plant, along with the classified image data. A convolutional neural network (CNN) was trained on bed camera images that were manually annotated to classify furnace bed height. The model was then used to generate a binary bedheight parameter over a 16-month period, and an extreme gradient boosting (XGBoost) model was applied to identify relationships with operating parameters across the recovery cycle. The outcomes of this research may offer deeper insights into the processes underlying bed dynamics. Ultimately, the developed system may serve as a tool for optimizing bed conditions and supporting stable combustion.
Journal articles
Guest Editorial: Carrying forward the tradition of fundamental research, TAPPI Journal June 2026
Since its first symposium in 1957, the Fundamental Research Symposium has evolved around fundamental research themes aimed at scientifically understanding papermaking. The symposium is organized by the Fundamental Research Committee (FRC), which is operated by the Fundamental Research Society (FRS). The unique format of the symposium, held at universities such as Oxford and Cambridge where participants stay together, fosters intensive academic exchange and collegial interaction.
Journal articles
Development and Application of a Real-Time Recovery Boiler E
Development and Application of a Real-Time Recovery Boiler Expert System, 1991 Engineering Conference Proceedings
Journal articles
Recovery of Sulfur from Spent Semichemical Pulping Liquors,
Recovery of Sulfur from Spent Semichemical Pulping Liquors, 1991 Engineering Conference Proceedings