Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Tetraethyl orthosilicate-containing dispersion coating — water vapor and liquid water barrier properties, TAPPI Journal September 2021
ABSTRACT: An aqueous styrene-butadiene latex dispersion coating containing in-situ processed tetraethyl orthosilicate (TEOS) applied on paperboard demonstrated improved water barrier performance. Coatings containing TEOS equivalent to 0.8% silicon dioxide (SiO2; dry basis) exhibited water vapor performance of < 25 g/m2/day (23°C, 50% relative humidity [RH]) and liquid water barrier performance Cobb 1800 s of < 6 g/m2, when applied as a single-layer 18 g/m2 coating. Cobb 1800 s barrier performance was still good (< 11 g/m2) at coat weights of 7•10 g/m2. The use of filler materials such as kaolin improved the vapor barrier properties of the coating, but this was not critical to the liquid water barrier properties.
Journal articles
Magazine articles
Web instability in the open draw and the impact on paper machine efficiency, TAPPI Journal May 2022
ABSTRACT: Paper is most likely to break in the first open draw on a paper machine where it is unsupported, wettest, and weakest. Tension is applied to peel the web from the roll surface, as well as minimize web flutter in the open draw. The average tension is well below the breaking point and is often set by adjusting the speed difference between the press and the next machine element by visually observing the behavior of the web. However, machine direction variations caused by instabilities in the paper machine can cause tension swings that exceed the strength of the web. Measurement of the web’s release point from press rolls on pilot and commercial paper machines was used to identify the cause of tension instabilities. Variations in the speed of the paper machine drives and the work of adhesion from the press roll surface were identified as key factors. Fluctuations of paper moisture, which affects the elastic modulus and strength of the web, appear to be less important.
Journal articles
Magazine articles
Improvements in oil and grease resistance (OGR) test methodology for waterborne barrier coatings, TAPPI Journal November 2022
ABSTRACT: Paper-based food packaging is becoming more popular due to consumer demands for sustainable packaging options. Waterborne paper coatings that provide performance properties (i.e., resistance to oil and grease) not inherent to paper and board substrates offer improved sustainability profiles over earlier paper treatment options, including fluorocarbon treatment and coating with extruded plastics. The continued development of new paper coating technologies requires re-evaluation of current test methods and development of new methods to ensure lab evaluations can serve as accurate predictors of real-world performance. This paper provides an overview of commonly used oil and grease resistance (OGR) test methods within the paper coatings industry, and then describes improvements and developments made to two key methods: the 3M Kit test and an internally developed oil breakthrough test. The combined use of these adapted methods provides a more efficient testing workflow and a more complete understanding of the OGR performance of barrier coatings.
Journal articles
A method to produce paperboard with a lightweight low-density coating, TAPPI Journal November 2025
ABSTRACT: In this work, a method is described in which a coating layer is produced that consists of a network of bubble-shaped air-filled voids within the coating. This is accomplished by instantaneously flash-drying all the water in the coating as it exits the application nip. The nip is formed between a polished chrome drum and a deformable press roll. The combination of the drum temperature, nip pressure, and nip width allow for sufficient energy to be transferred to the coating to completely flash-dry the coating material. The pressure within the nip is sufficient to allow the coating to superheat within the nip, then flash boil as it exits the nip. This boiling effect and resulting expansion are constrained by the roll surface, resulting in a coated surface that mirrors the polished chrome surface. The coating immobilizes while in the process of boiling, which preserves the bubble structure. With a coat weight of 5 g/m2, a flat, smooth surface is produced. This process was scaled up to a mill production machine layout and run at speeds as high as 450 m/min.
Journal articles
Magazine articles
Rewet in wet pressing of paper, TAPPI JOURNAL September 2018
Rewet in wet pressing of paper, TAPPI JOURNAL September 2018
Journal articles
Magazine articles
Citrus-based hydrocolloids: A water retention aid and rheology modifier for paper coatings, TAPPI Journal July 2019
ABSTRACT: The rheological and dewatering behavior of an aqueous pigmented coating system not only affects the machine runnability but also affects the product quality. The current study describes the use of natural hydrocol-loids derived from citrus peel fibers as a rheology modifier in paper coating applications. The results were compared with carboxymethyl cellulose (CMC) in a typical paper coating system. Water retention of the coating formulation was increased by 56% with citrus peel fibers compared to a default coating, and it also was higher than a CMC-containing coating. The Brookfield viscosity of paper coatings was found to increase with citrus peel fibers. Compared to CMC, different citrus peel fibers containing coating recipes were able to achieve similar or higher water retention values, with no change or a slight increase in viscosity. Coatings were applied on linerboard using the Mayer rod-coating method, and all basic properties of paper were measured to assess the impact of citrus peel fiber on the functional value of the coatings. Paper properties were improved with coated paper containing citrus peel fibers, including brightness, porosity, smoothness, surface bonding strength, and ink absorption.
Journal articles
Magazine articles
The evolution of reel statistical methods, TAPPI Journal June 2019
ABSTRACT: Multiple statistical methods for calculating the variance partition analysis (VPA) of reel data have existed for decades. In the paper industry, VPA is also commonly known as reel statistics. VPA commonly consists of total variance (TOT) that is then divided into three components: cross direction (CD), machine direction (MD), and residual (RES). A common mathematical procedure is referred to as ANOVA (analysis of variance). TAPPI Standard Test Method T 545 “Cross-machine grammage profile measurement (gravimetric method)” addresses paper testing and includes the ANOVA equations that have also been used to analyze scanning data.In the 1990s, TAPPI published TIP 1101-01 “Calculation and partitioning of variance using paper machine scanning sensor measurements,” which contained simple formulas that were easy to implement and could be used by a nov-ice to generate statistics on a spreadsheet. All involved quality control system (QCS) suppliers agreed to support this common method in their QCS. TIP 1101 was recently revised, and this paper concerns the analysis of data collected from a scanning sensor in a QCS and the creation of a common method for the calculation of reel statistics by TAPPI’s Process Control Division.
Journal articles
Magazine articles
Contrasting underlying mechanisms of different barrier coating types, TAPPI Journal January 2018
Contrasting underlying mechanisms of different barrier coating types, TAPPI Journal January 2018
Journal articles
Analysis of wrinkle formation and propagation during paperboard deep drawing, TAPPI Journal October 2026
ABSTRACT: Paper-based packaging is becoming increasingly important as a sustainable alternative to plastics. Among forming processes, deep drawing is particularly promising due to its high cost-effectiveness, short processing times, and suitability for large-scale production. A major challenge, however, lies in the formation of wrinkles, which impair the visual quality, functional performance, and dimensional stability of the packaging, thereby affecting subsequent processes such as filling, printing, and sealing. This study focuses on analyzing the occurrence and propagation of wrinkles during the deep drawing of paperbased materials to derive fundamental insights and strategies for prevention. The wrinkles arise from tangential compressive stresses in the flange and the material’s limited thickening, leading to local stability failures once a critical stress threshold is exceeded. A combined approach of experimental investigations, numerical simulations, and analytical considerations was used to examine a rotationally symmetrical part. A transparent die enabled spatial observation of wrinkle initiation and growth. First, wrinkles were found to typically initiate in the cross direction (CD), while most wrinkles develop in the machine direction (MD). By comparing analytically and numerically determined stress distributions, the mechanisms of wrinkle formation can be understood both locally and temporally, thereby enabling the prediction of wrinkle occurrence.
Journal articles
Aqueous polymer dispersions from long chain cellulose fatty acid ester for coating of paperboard, TAPPI Journal October 2026
ABSTRACT: Fiber-based substrates are coated with aqueous polymer dispersions to obtain the necessary barrier properties for, e.g., food service, takeaway, and other packaging applications. There is interest to replace non-renewable substances driven by the concerns over the price stability and depletion of fossil resources, environmental and safety issues, and legislative actions. In this study, we demonstrated that stable aqueous polymer dispersions with solids content of at least 35% can be prepared from a long chain cellulose fatty acid ester (cellulose octanoate) using both solvent-based and thermomechanical processes. In the solvent-based process, water and additives were mixed with a polymer dissolved in chloroform followed by solvent removal. In the thermomechanical method, water and stabilizers were added into polymer melt under mixing in a pressurized reactor. Dispersions were tested as coatings on paperboard and assessed for their grease resistance and water and oil barrier. Oil barrier was clearly improved with most of the dispersions. In addition, proper film formation was necessary for achieving improved water barrier. However, the stabilizing system had a clear impact on the dispersion stability and the water barrier performance of these coatings.