Search

Co-pulping of Trewia nudiflora and Trema orientalis, TAPPI Journal June 2023

ABSTRACT: Trewia nudiflora, a fast-growing species, was evaluated as a pulpwood. The a-cellulose content of this species was 40.4% with a Klason lignin of 21.5%. It was characterized by shorter fibers with a thin cell wall. The pulp yield was 40% with a kappa number of 16 at the conditions of 18% active alkali charge and 30% sulfidity for 2 h cooking at 170°C. T. nudiflora was similar to Trema orientalis in anatomical, morphological, and chemical composition; therefore, mixed chips at a 50:50 mixture ratio were cooked under optimum conditions. The pulp yield of mixed chip cooking was 45.4% with a kappa number of 19.4. The tensile and tear index of T. nudiflora pulps were 64.8 Nœm/g and 11.5 kPaœm2/g at 35 °SR, respectively. The mixed chips, T. nudiflora, and T. orientalis pulps showed above 81% brightness when bleached by D0(EP)D1 sequence using 20 kg chlorine dioxide (ClO2)/ton of pulp.

Editorial: Shaping industry and career success with TAPPI Standards involvement, TAPPI Journal May 2023

ABSTRACT: Within TAPPI, there are many ways to help advance our industry and make sure it thrives for years to come. Writing a research paper for publication or acting as peer reviewer for TAPPI Journal, presenting at a conference or helping to organize one, and becoming involved in the many committees that are part of TAPPI Divisions are just some of the ways. One other very important way to contribute to our industry is through the standards development process.

Dissolution of wood components during hot water extraction of spruce, TAPPI Journal May 2023

ABSTRACT: The purpose of this study was to investigate the autohydrolysis of softwood, which is the main chemical operation in both hot water extraction and steam explosion. Control of the process and monitoring its course were ensured by the careful choice of experimental setup and conditions: a milled spruce material was extracted in a small flow-through reactor to minimize degradation of the dissolved material and to enable analysis of the resulting liquors extracted at selected time points. The obtained liquid and solid fractions were analyzed for sugar composition and acetic acid concentration. The results showed that partially degraded hemicelluloses were extracted; hemicelluloses side chains were cleaved off and detected as monomers, while deacetylation was limited. Chain scissions of cellulose were observed as a result of autohydrolysis.

Information Learned from the Genetic Engineering of Recalcitrant Monocot Species: Applicability to Problems in Forest Biotechnology, 1997 Biological Sciences Symposium Proceedings

Information Learned from the Genetic Engineering of Recalcitrant Monocot Species: Applicability to Problems in Forest Biotechnology, 1997 Biological Sciences Symposium Proceedings

Influence of base sheet properties on barrier coating performance, TAPPI Journal November 2025

ABSTRACT: Paper packaging offers a sustainable alternative to standard plastic-based materials, particularly for food and beverage applications. With reduced fiber treatment options like fluorochemicals, uncoated base stock often provides little-to-no effective barrier against liquid water, oil/grease, or moisture transmission. Despite the lack of natural barrier performance, base sheet properties can significantly influence the efficiency of applied waterbased barrier coatings. In this study, various base stock properties, such as caliper, porosity, roughness, and ash content, are reported to influence the barrier performance of styrene-acrylic and a copolymer of styrene-butadiene/styrene-acrylate based barrier coatings. These findings will help paper and board producers design better, more cost-effective, purposebuilt substrates for barrier applications in the packaging industry.

A laboratory-scale automated vacuum-assisted device for coating of cellulose nanofibrils onto paper, TAPPI Journal November 2025

ABSTRACT: An automated vacuum-assisted coating system was developed to deposit cellulose nanofibril (CNF) layers onto paper substrates, simulating potential industrial geometries while allowing precise control of web speed (10•20 m/min), vacuum time (up to 30 s), and applicator gap (0.5•0.9 mm). Vacuum assistance makes it possible to obtain coat weights over 5 g/m2 in a single pass and increases solids after coating from less than 10% to over 28%• 30%, reducing drying demand by more than 60%. Coat weights were tuned from 6 to over 11 g/m² by varying suspension solids (0.4•0.6 wt%), line speed, and filtration length (20•40 mm), with strong agreement between experimental data and model predictions. Barrier testing showed Kit test values for double folded samples of 9•12 and Gurley air resistances above 4 × 104 s once coat weights exceeded 7 g/m². Comparable performance was achieved with lower fines content CNF (60%) by increasing coat weight, providing technical flexibility and cost advantages for industrial scale-up.

The industry is entering a pivotal moment in which many of us find ourselves engaged in deep soul searching. Since the days of Francis Bacon when the illustrious triumvirate of gunpowder, the compass, and paper were the drivers of civilizations, our commu

The industry is entering a pivotal moment in which many of us find ourselves engaged in deep soul searching. Since the days of Francis Bacon when the illustrious triumvirate of gunpowder, the compass, and paper were the drivers of civilizations, our community has enjoyed a noble place at the table. Indeed, especially over the last 100 years, pulp and paper has quietly powered communication, commerce, and, more than ever today, packaging, thus representing a steady backbone for the continued stability of many global industries.

Paper360°’s 2025 Power List, Paper360º September/October 2025

Qualifying novel bio-based materials for the market: EHS, sustainability and beyond, TAPPICon25

Advancing Decarbonization in Pulp and Paper Manufacturing: A Cell-Free Enzyme Process for Enhanced Dewatering and Drying, TAPICon25