Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
On the design of corrugated boards: A new FEM modeling and experimental validation, TAPPI Journal August 2025
ABSTRACT: This study presents a simplified finite element modeling (FEM) approach suitable for large structures made of corrugated boards, such as customized packages, based on a homogenization method, which is combined with correction factors for internal mechanisms. The homogenization process reduces computational time by transforming flute geometries into equivalent elastic models. In large deformations and in the presence of contact for a given geometry, the effective elastic modulus in the thickness direction, as well as the effective thickness of the structure, are corrected by two statistical Weibull distributions representing the contact and buckling mechanisms in a corrugated board. The Weibull parameters are obtained via experimental analysis, and such a process is then validated. The results demonstrate that the statistical parameters (â1 = 0.14, â2 = 1.31) can be used for the simplistic representation of corrugated boards, being computationally efficient. This research contributes to the optimization of corrugated packaging design, specifically by simplifying FEM models for faster, yet equally accurate, simulations.
Journal articles
Reinforcing folding boxboard ply stock with refined pulp and its effect on dewatering potential, TAPPI Journal February 2025
ABSTRACT: The folding boxboard (FBB) filler ply typically contains a significant amount of mechanical pulp such as bleached thermomechanical pulp (BTMP), bleached chemi-thermomechanical pulp (BCTMP), and chemi-thermomechanical pulp (CTMP), etc. It is usually reinforced with either refined broke from the same paper machine line and converting process or by utilizing traditional bleached kraft pulp (BKP). In response to the drive for improved/increased ply bond (to avoid undesired delamination), increased bulk, reduced basis weight, and minimized energy consumption, papermakers have experimented with various options and strategies. In between the common approaches, choices have been made between reducing the refining of the mechanical pulp, increasing the broke refining (more frequently practiced on the production scale), or increasing the BKP refining (a potentially superior choice). This study focused on a simplified approach to assess the impact of three reinforcement pulps with different refining levels on the dewatering of the filler ply. The reinforcement pulp was added to the core stock for the FBB filler ply — a mechanical pulp, BCTMP, with a drainability of 25 °SR. The proportions of the reinforcement pulp, hardwood bleached kraft pulp (HWBKP), were 20% of 30-35 °SR, 10% of HWBKP 50-55 °SR, and 5% of HWBKP 70-75 °SR. The intention behind using varying percentages of reinforcement pulp was to attain a controlled internal bond while enhancing bulk through increased mechanical pulp content. The dewatering potential of the stock mixtures was assessed at three vacuum levels — 4, 10, and 25 kPa — that can be found in progressive stages within production- scale forming sections. Our goal was to find an optimal reinforcement strategy for filler ply that would minimize the use of the reinforcement pulp, give better strength, retain bulk, and lower basis weight. The success of this strategy was verified with an actual FBB machine.
Journal articles
Filtration performance of face masks and facepiece respirators used during COVID-19 pandemic, TAPPI Journal February 2025
ABSTRACT: The rapid spread of SARS-CoV-2 has created challenges for societies, healthcare settings, businesses, and institutions. To curb virus transmission, various measures like lockdown, social distancing, hand hygiene, and using appropriate personal protective equipment (PPEs), including face masks, have been recommended. Face masks and facepiece respirators are considered to act as barriers against microbial transmission from person to person. In this study, we selected barrier materials used during the COVID-19 pandemic that included four non-medical face masks and three facepiece respirators. Facepiece respirators were distributed by the U.S. Administration through pharmacy outlets. Results showed that facepiece respirator R95 has the highest filtration efficiency (above 99%), which remains more or less the same over different particle sizes. The N95 respirator’s filtration efficiency was lower than that of R95, but its barrier resistance was lower than that of the R95, indicating that it can be comfortably used over longer duration. Face masks were evaluated using ASTM F 3502-24 for their barrier performance. At 0.1 and 0.3 ìm particle size, domestically manufactured masks met the standard for higher performance. Interestingly, the results indicate that quality of raw materials and manufacturing standards play important roles, as is evident in domestically manufactured face mask and facepiece respirators.
Journal articles
Comparison of the application of polysaccharide-based barrier coatings on paper using film press and spray coating, TAPPI Journal January 2025
The growing demand for sustainable packaging has spurred research into biopolymer-based solutions and their application to paper substrates. This study compares the application of low solids, high viscous aqueous solutions of alginate and chitosan on two different paper substrates using a laboratory film press coater and a purpose-built spray coating unit, with a focus on barrier performance and practical industry considerations. Key parameters investigated are air flow rate, water vapor transmission rate, and grease resistance. Results showed that due to the low solids content of the applied biopolymer solutions, film press coating required a double-layer application for coat weights exceeding 4 g/m², making it less viable for industrial application. In contrast, spray coating allowed for higher application weights in a single step. The barrier properties of spray coated samples, compared to film press coatings, varied with the paper substrate: spray coating performed better on one substrate and worse on the other. Contact angle measurement of the substrates suggested that spray coating is more suitable for a more hydrophilic substrate because of improved surface wetting. The study also identified issues with drying conditions and pinholes affecting the quality of spray coated samples, indicating a need for further research to optimize these parameters.
Journal articles
Water-based adhesive penetration into paperboard and coated paperboard, TAPPI Journal January 2025
The setting of water-based adhesives in contact with paperboard is important in the production of boxes and other packaging, but the topic has received little attention in the literature. The penetration of the adhesive into the paper surface is important to get good bond strength through mechanical interlocking. The influence of the process conditions and the paper properties on this penetration is lacking. A water-based adhesive was applied to an uncoated and coated paperboard. The coating layer had two latex levels. Samples were characterized in terms of air permeability, void fraction, average pore size, and coat weight. The adhesive was applied to the samples in a mechanical press, squeezing a drop between two samples. The penetration of the adhesive was characterized with a silicone oil absorption method that measured the decrease in pore volume after the adhesive had been applied to approximate the pore volume taken up by the adhesive. The bond strength was measured with a peeling test. The penetration depth into uncoated paper did not depend on the application method parameters such as pressing time, pressure, or initial solids of the adhesive. The penetration depth ranged from 35•40 mm. The penetration into 10 pph latex content coated paper was similar to the uncoated samples, but reduced penetration was observed into the 40 pph latex content coatings. The results were compared to the limiting amount of adhesive that was obtained from the weight gain of the samples and to a simple model that is based on flow in porous media. Peel tests revealed that good penetration was needed, as well as a strong coating layer to obtain high peel forces.
Journal articles
Editorial: Design considerations for developing high-quality flexible packaging laminates, TAPPI Journal July 2025
ABSTRACT: The global flexible packaging industry has constantly evolved by developing new materials, film design, polymer processing techniques, and machinery to overcome challenges posed by consumer demands, regulation, and societal pressure. While achieving superior quality and improved mechanical film attributes has always been the cornerstone for new technical developments in this industry, the end-of life shortcoming for most plastic films has driven the value chain to strive harder to design and develop sustainable packaging structures.
Journal articles
19th European PLACE Conference highlights challenges of balancing sustainability with product protection, TAPPI Journal July 2025
ABSTRACT: The European PLACE (Polymers, Laminates, Adhesives, Coatings and Extrusion) Committee was founded in 2023 with the goal of continuing a biennial conference for the flexible packaging and converting industry, including converters, OEMs, raw materials suppliers, and academia. Previous iterations of the PLACE Conference were organized by TAPPI, but the new European Place Committee has now found a home within bdvi e.V. (Bund Deutscher Verpackungsingenieure), which is the Association of German Packaging Engineers, a registered nonprofit organization.
Journal articles
Data-efficient determination of machine-specific process windows in thermoforming using the example of PCR materials, TAPPI Journal July 2025
ABSTRACT: In an industrial context, process windows for thermoplastics in thermoforming processes are still often determined through time-consuming trial-and-error approaches. This results in increased effort when commissioning new machines, implementing new technologies, or substituting sheet materials. One key reason is the lack of methods that allow for efficient, process-related assessment of material behavior and a quantitative definition of a “target state” of the heated sheet in relation to geometry and process conditions. In this study, we present the In-Situ Thermoforming Characterization (ITC) method as an application-oriented approach that enables format-independent evaluation of material behavior directly within the forming station of a thermoforming system. The method was successfully applied to a material substitution case, replacing conventional virgin polypropylene (PP) with post-consumer recyclate (PCR) — in this case, recycled PP (rPP) — in the production of a defined cup geometry. The results enabled the transfer of existing process knowledge from the virgin material to the recyclate, thereby accelerating material qualification. Based on the collected data, material behavior under process conditions could be mapped within the design space, making it possible to identify machine settings that deliver equivalent forming results in our test setup. Overall, the method shows strong potential for efficient and precise determination of machine-specific process windows.
Journal articles
Editorial: Investing in Amercian advanced manufacturing, TAPPI Journal June 2025
ABSTRACT: American manufacturing is seeing a renewal, which is needed to boost jobs in America, particularly in the middle and manufacturing base of the country. The ongoing tariff situation emphasizes the importance of protecting domestic manufacturing. There is U.S. congressional agreement, in principle, to bring back manufacturing to the United States. However, given how the global trade and manufacturing space has shifted in the last four decades, it may not be a comparative advantage to manufacture low margin and labor-intensive products. Officials in the current U.S. Administration have stated that manufacturing of socks and T-shirts is not necessarily in the interest of the United States, but focusing on value-added products is essential. While silicon chips, solar panels, and batteries are key items of interest, advanced textile materials such as those that find applications in industrial products and composites, products that can save human lives, and products for protecting the environment are highly-valued items that cater to national security.
Journal articles
Materials performance considerations in hydrothermal liquefaction conversion of biomass, TAPPI Journal June 2025
ABSTRACT: Hydrothermal liquefaction (HTL) is a promising thermochemical route developed to convert woody biomass and biowaste to biochemicals and bio-oils. However, the operating conditions are rather harsh to biorefinery structural metallic components. These conditions include alkaline catalysts such as potassium carbonate (K2CO3); hot, pressurized (sub-critical) water reaction; and medium and aggressive anions chlorine (Cl•) and hydrogen sulfide (H•) released from biomass feedstocks. Thus, selection of suitable structural alloys for biorefinery components involves striking a balance between mechanical properties, corrosion resistance, and cost. Alloys currently being considered for this application include ferritic-martensitic steels and austenitic stainless steels. From a corrosion perspective in hot pressurized water, the former typically exhibits higher stress corrosion cracking resistance, whereas the latter exhibits higher corrosion resistance. This study reviews cost-effective corrosion control strategies aimed at increasing the chromium (Cr) content for protective surface oxide formation, as screened by testing in simulated HTL alkaline water, to support materials selection and design. Corrosion control strategies include surface modification (increasing surface Cr content), alloying (increasing bulk Cr content), and stainless-steel type (ferritic vs. austenitic). Of the alloys considered (including those subjected to surface modification), ferritic stainless steels exhibit a promising balance between corrosion and stress corrosion cracking resistance, adding another family of candidate alloys for structural biorefinery component materials selection and design.