Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Event Type
Collections
Journal articles
Pilot-made, highly extensible paper for dry 3D forming, TAPPI Journal May 2025
Cellulose fiber-based packaging materials must perform well in demanding three dimensional (3D) forming process conditions. On the other hand, the development of manufacturing concepts is required for improved competitiveness of bio-based materials. This study covers some key factors that influence the extensibility of cellulose fiber-based structures and presents a pilot-scale development study of a 3D formable material concept. Bleached softwood kraft (BSK) pulp from a Nordic pulp mill was used in the pilot trials. Cellulose-based webs were formed using water-laid and foam-laid web forming using a pilot paper machine. For the water-laid forming, the BSK pulp was refined by applying a high consistency (HC) phase at over 40% consistency, followed by a low consistency (LC) refining at 4% consistency. The BSK pulp was refined for the foam-laid forming by only applying lowconsistency refining. In the foam-laid web forming, anionic sodium dodecyl sulfate (SDS), two foamable latexes, and polyvinyl alcohol (PVA) were used as foaming agents. The pilot rolls were dried at a separate steam cylinder dryer pilot and compacted in-plane in the machine direction (MD) at a separate pilot machine. Tensile properties of the treated paper webs were measured and evaluated with respect to achieved web shrinkage. The same dimensional contraction brought by shrinkage was almost strained out in tensile testing. The results indicated that the shrinkage that occurred by drying and in-plane compaction depended on the pulp furnish. The water-laid material achieved about 30% elongation, whereas the foam-laid material achieved significantly above 50% elongation. The 3D forming performance of the dry materials was tested using fixed and sliding blank methods. The dry paper sheets performed well enough in 3D forming for application to many consumer package applications according to their extensibility.
Journal articles
Magazine articles
Study on the effect of aluminum diethyl phosphinate in synergy with ammonium polyphosphate on the flame retardancy of cellulose paper, TAPPI Journal April 2025
ABSTRACT: This paper involved the synergistic incorporation of ammonium polyphosphate (APP) and diethyl aluminum phosphinate (AlPi) as flame-retardant fillers for producing flame-retardant paper. The research revealed that APPs were square particles with a smooth surface, and their solubility was 0.29 g/100 mL at 20°C, which increased to 4.12 g/100 mL at 60°C. The surfaces of AlPis were rough and irregular. The solubility of AlPi was 0.023 g/100 mL at 20°C, and the solubility remained stable when the temperature increased. The addition of AlPi had a minor influence on the pulp beating degree. The tensile strength of kraft/APP/AlPi decreased with the increase of the AlPi addition. For a paper with 20 wt% APP and 0 wt% AlPi, the limiting oxygen index (LOI) value was 27.2%, and it burned completely at the eighth second during vertical combustion. When the AlPi additive content increased to 20 wt%, its LOI value increased to 32.2%, and the vertical combustion self-extinguished as soon as the flame was removed. Scanning electron microscopy (SEM) showed that the char residue of the kraft/APP/AlPi had a more complete fiber network structure than that of kraft/APP. The Raman spectroscopy indicated that the area ratio of the D (amorphous phase; disordered graphite vibration) band to the G (crystal phase; graphite carbon vibration) band (ID/ IG) ratio of kraft/APP/AlPi was lower than that of kraft/APP, meaning that the graphitization degree of the char residue of kraft/APP/AlPi was higher than that of kraft/APP, which indicated the kraft/APP/AlPi had better flame retardancy.
Journal articles
Controllable conversion of cellulose nanocrystals to cellulose microspheres: Insight on the effect of parameters during spray drying, TAPPI Journal February 2025
ABSTRACT: Cellulose microspheres, which have mainly been produced via the sol-gel method up until now, exhibit a promising potential for broad applications due to their regular microstructure and renewability. However, some issues with production of cellulose microspheres, such as the recycling of involved organic solvents and the removal of the residual solvents, should be solved. In this study, a cellulose nanocrystals (CNCs) suspension was used to produce cellulose microspheres via spray drying in order to avoid the use of organic solvents. The effects of CNCs particle size, CNCs concentration, and inlet temperature of spray drying on microstructure and particle size of cellulose microspheres were investigated. The results indicated that the optimal average particle size and concentration of CNCs used for obtaining cellulose microspheres were 106 nm and 0.1 wt%, respectively. Under the optimal conditions, cellulose microspheres with a regular spherical morphology and an average particle size of ca. 3 ìm were obtained. The sulfuric acid hydrolysis and spray drying process barely affected the crystalline structure of cellulose. However, the introduced sulfhydryl groups, which were confirmed by Fourier transform infrared spectroscopy results, degraded the thermostability of cellulose. Generally speaking, converting CNCs to cellulose microspheres via spray drying is beneficial for promoting the controllable and continuous production of cellulose microspheres.
Journal articles
Reinforcing folding boxboard ply stock with refined pulp and its effect on dewatering potential, TAPPI Journal February 2025
ABSTRACT: The folding boxboard (FBB) filler ply typically contains a significant amount of mechanical pulp such as bleached thermomechanical pulp (BTMP), bleached chemi-thermomechanical pulp (BCTMP), and chemi-thermomechanical pulp (CTMP), etc. It is usually reinforced with either refined broke from the same paper machine line and converting process or by utilizing traditional bleached kraft pulp (BKP). In response to the drive for improved/increased ply bond (to avoid undesired delamination), increased bulk, reduced basis weight, and minimized energy consumption, papermakers have experimented with various options and strategies. In between the common approaches, choices have been made between reducing the refining of the mechanical pulp, increasing the broke refining (more frequently practiced on the production scale), or increasing the BKP refining (a potentially superior choice). This study focused on a simplified approach to assess the impact of three reinforcement pulps with different refining levels on the dewatering of the filler ply. The reinforcement pulp was added to the core stock for the FBB filler ply — a mechanical pulp, BCTMP, with a drainability of 25 °SR. The proportions of the reinforcement pulp, hardwood bleached kraft pulp (HWBKP), were 20% of 30-35 °SR, 10% of HWBKP 50-55 °SR, and 5% of HWBKP 70-75 °SR. The intention behind using varying percentages of reinforcement pulp was to attain a controlled internal bond while enhancing bulk through increased mechanical pulp content. The dewatering potential of the stock mixtures was assessed at three vacuum levels — 4, 10, and 25 kPa — that can be found in progressive stages within production- scale forming sections. Our goal was to find an optimal reinforcement strategy for filler ply that would minimize the use of the reinforcement pulp, give better strength, retain bulk, and lower basis weight. The success of this strategy was verified with an actual FBB machine.
Journal articles
Optimizing Water and water vapor barrier properties of water-based barrier coatings
Functional coatings are applied to paper and paperboard substrates to provide resistance, or a barrier, against media such as oil and grease (oil and grease resistance; OGR), water, water vapor (moisture vapor transmission rate; MVTR), and oxygen, for applications such as food packaging, food service, and other non-food packaging. Typical functional barrier coatings can be created by applying a solid coating or extruded film, a solvent-based coating, or a water-based coating to the paper substrate using various means of coating applicators. Today, there is increasing interest in developing recyclable and more sustainable approaches to producing these types of packages. This paper focuses on water-based barrier coatings (WBBC) for water resistance and MVTR for medium barrier performance. The main goal was to improve the performance of existing barrier polymers using additives such as waxes. Barrier coated systems were evaluated in single layer laboratory coating studies. This paper reviews examples of improving the performance of barrier polymers studied, including styrene butadiene and styrene acrylate, using wax additives. Regulatory challenges with paraffin waxes have resulted in the focus on bio-waxes. The results showed that small amounts of bio-wax can significantly improve barrier properties, especially for water resistance and MVTR. The choice of the best combination of binder and wax is essential. The influence of the bio-wax additive on blocking tendency, coldset glue strength, or heat seal strength is negligible.
Journal articles
The influence of precoating layers on the performance of water-based barrier coatings, TAPPI Journal January 2025
Cellulose nanofibrils (CNF) on paper have been demonstrated to be an effective barrier against oxygen and grease and have been shown to improve the barrier performance of dispersion-based barrier coatings. The potential to produce paper grades that have good oxygen, grease, and moisture barrier properties is clear, but a better understanding of the synergies between CNF, other coating layers, and water-based barrier coatings (WBBC) is needed to optimize these systems. Different coat weights of a commercial WBBC were applied to papers that have a range of different qualities and thicknesses of CNF precoating layers. The same WBBC was also applied to pigmented coated paper, with various types of pigments and latex levels. Samples were characterized in terms of grease resistance, water vapor transmission rate (WVTR), and oxygen transmission rate (OTR) before and after folding. The results were contrasted to cases where the WBBC was applied to the paper with no precoating layer. When the WBBC is applied on a CNF layer or the pigmented coating layer, the performance of the WBBC for the water vapor barrier improves a significant amount compared to when the WBBC is applied to the base paper with no precoating layer. This improvement likely comes from these precoating layers filling in the large paper pores, which leads to the WBBC forming a continuous layer at low coat weights. Folding decreases the moisture barrier performance to some degree, but the grease resistance is not influenced by folding when a CNF precoating layer is involved. Oxygen barrier properties are moderate for the CNF layer alone and are less than 5 cm3/m2/day when WBBC is coated on the CNF layer. This result likely comes from the barrier coating’s ability to repair defects in the CNF layer to stop the easy passage of oxygen in defect regions of the sample.
Journal articles
Magazine articles
CFD and predictive modeling of temperature and calcination in a rotary lime kiln • Potential for steadier kiln operation, TAPPI Journal October 2024
ABSTRACT: Rotary lime kilns are used in the pulp and paper industry to calcine lime mud to lime. Lime kiln models provide a means to understand the complex phenomena occurring within the kiln to aid in problem-solving during operation. A two-dimensional (2D) computational fluid dynamics (CFD) and one-dimensional (1D) bed model was previously developed for steady-state and transient analysis. This study explores data extracted from the model over a longer time period. The simulated outlet gas and shell temperature are compared to measured data for validation. The capability of using the model to estimate the production rate, accounting for the residence time within the kiln, is discussed. The maximum refractory wall temperature is analyzed during operation. Fluctuations in the calcination location are compared to outer shell heat-map data to correlate the calcination location and ring formation and growth. The model results to date indicate that fluctuations in the calcination zone may contribute to problematic ring growth, though a direct correlation has yet to be established. Additionally, a method for steadier kiln control is introduced and discussed. A machine learning model is also developed to predict the calcination start location from industrial data and is compared to the CFD model for validation. This model can generate results quickly and without the need for knowledge in CFD software and theory. Good agreement is found between the CFD and machine learning model during operation, with a mean absolute error (MAE) of 0.46 m, a mean absolute percentage error (MAPE) of 0.92%, and a root mean square error (RMSE) of 1.17 m.
Journal articles
Magazine articles
Model development for real oxygen delignification processes, TAPPI Journal October 2024
ABSTRACT: Previous extensive work has been done on modeling the oxygen delignification process, based on how the basic parameters, i.e., temperature, kappa number, concentration of alkali, and concentration of oxygen, affect the delignification rate. However, these models are not used extensively to evaluate the performance of real processes, primarily because they have not been able to properly consider all the essential issues affecting delignification in practice. Such issues include the mass transfer and consumption of oxygen, which defines the concentration of dissolved oxygen in the process, and the effect of that concentration on the delignification rate. In this paper, a new way to model the oxygen delignification process is used in which these parameters, among other smaller matters, are taken into account. The basic model and its parameters were defined by the information obtained from the literature, delignification made in the laboratory tests, and mill processes and mill tests. An essential aspect of these studies was the information obtained from the oxygen concentration measured in the residual gas obtained from the top of the reactor. With the aid of this measurement, it was possible to define more accurately the consumption of oxygen and partial pressure of oxygen that define the concentration of dissolved oxygen in the reactor. Using mill experiments, a model was formed that predicts the operation of the oxygen delignification process. The model was used to show how much the process could be improved by optimizing the charge of the oxygen. The mill experiments also confirmed that mass transfer of oxygen is modeled correctly enough, except when the charge of oxygen is very low and/or the mixing is not efficient enough. In that case, there is variation in the concentration of oxygen in the process that should be taken into account in the modeling.
Journal articles
Magazine articles
Colloid chemical aspects of paper formation in the presence of nanofibrillated cellulose and cationic starch, TAPPI Journal September 2024
ABSTRACT: A series of experimental tests were carried out to examine colloidal-scale consequences of optionally treating nanofibrillated cellulose (NFC) with cationic starches of different charge density and dosage (0.5% or 2.0% by weight), adding that material to a furnish prepared from 100% recycled copy paper, and then subjecting the mixture to very different levels of hydrodynamic shear. Tests included optical microscopy, sediment volume tests, sediment velocity tests, and “percent fines” assessment by means of a fiber quality analyzer (FQA). In addition, the zeta potential and charge demand of the studied materials were evaluated. Optical imaging revealed that cationic starch treatment of the NFC tended to agglomerate it into multiparticle clusters, which sometimes could be mostly redispersed by hydrodynamic shear. Subsequent addition of the starch-treated NFC to the default furnish resulted in much of the colloidal material becoming attached to fibers. Subsequent shearing of the mixtures was at least partly effective in separating the clusters of NFC from the fiber surface, resulting in essentially a two-component mixture. Multiparticle NFC clusters coexisted with the fiber suspension, sometimes attached and sometimes not, depending on the details of treatments. Sediment volume tests showed that systems containing cationic starch-treated NFC tended to have a higher density after settling in comparison to untreated NFC; these findings are consistent with the cationic starch acting as a stabilizer on the solid surfaces, allowing them to slide past each other during the settling process. Application of intense hydrodynamic shear tended to result in denser sediment. Results of tests with the sediment velocity messurement and the FQA percent fines assessment did not correlate well with changes in test conditions considered in this study.
Journal articles
Magazine articles
Sulfur makeup in an unbleached kraft pulp mill, TAPPI Journal August 2024
ABSTRACT: Sodium sesquisulfate or “sesqui” (Na3H(SO4)2) is a by-product of chlorine dioxide production at kraft pulp mills. It is typically used for sodium and sulfur makeup in the liquor loop. Mondi Hinton Inc. (MHI) in Hinton, AB, Canada, was converting from bleached to unbleached kraft pulp production and was thus losing this source of makeup. The only option that was readily available as a substitute was sodium hydrosulfide (NaHS), which was cost prohibitive. Other options such as sodium sulfate (Na2SO4), emulsified sulfur, sulfuric acid (H2SO4), and sodium bisulfite (NaHSO3) were compared. The mill concluded that pelletized sulfur plus sodium hydroxide or “caustic soda” (NaOH) was the best option. Laboratory-scale experiments showed that pelletized sulfur dissolved in white liquor (WL). A mill-scale trial revealed that pelletized sulfur added to a causticizer had no adverse impacts on the downstream pressure filters or kiln operation. The sulfur reacted to produce polysulfide upstream of the WL storage tank, giving the liquor an orange hue. This polysulfide appeared to partially degrade into thiosulfate before being fed to the digester. The heavy black liquor (HBL) sulfur:sodium (S:Na) ratio did not change significantly, even though the sulfur/soda addition location was upstream of the original one. In addition, other properties such as liquor heating value and elemental analysis did not significantly change. Due to polysulfide/thiosulfate concentration in the white liquor, it was determined that the carbon steel equipment was at risk for corrosion. During the annual turnaround that occurred eight months after the addition of sulfur was started, the wash zone of the digester showed no signs of thinning/damage. The mill has been running exclusively with pelletized sulfur for 22 months (as of August 2024), realizing significant cost savings compared to the use of NaHS or other sulfur/soda addition options.