Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Peracetate/singlet oxygen chemistry used in post-bleaching of kraft pulp as a practical oxidant for paper machines, TAPPI Journal May 2021
ABSTRACT: The use of a novel sodium peracetate/singlet oxygen chemistry for brightening bleached kraft pulp shows exciting potential for technical performance, supply logistics, safety, and cost reduction. Potential chemical carryover to the paper machine raises questions about whether peracetate will impact paper machine performance, such as metal corrosion, useful press felt life, and interference with existing biocide programs or paper machine chemistry. Sodium peracetate/singlet oxygen chemistry can be used in high-density storage chests for brightening/whitening and to increase color stability. Any oxidant used directly before the paper machine has the possibility of impacting paper machine operations. Traditional oxidants used in bleaching, such as chlorine dioxide and hydrogen peroxide, are known to cause corrosion on machinery metals and press felts. Hydrogen peroxide residuals can interfere with common biocide programs. Traditional oxidants used in biocide treatments themselves significantly degrade press felt life when the rule-of-thumb concentration thresholds are exceeded. Sodium peracetate is evaluated in this paper for its impact on nylon press felt fiber degradation, metal corrosion, and interference with typical biocide programs.Laboratory results indicate that sodium peracetate/singlet oxygen chemistry is less corrosive than chlorine, bromine, and hydrogen peroxide on press felt nylon fiber and can therefore be used at higher levels than those chemistries to increase brightness without increasing negative downstream impact. Sodium peracetate can also be used with current biocide programs without negative impacts such as consumptive degradation. Higher residuals of peracetate going to the paper machine may be useful as a biocide itself and can complement existing programs, allowing those programs to stay within their safe operating levels and thereby extend press felt useful life.
Journal articles
Magazine articles
Gas dispersion in the oxygen delignification process, TAPPI Journal May 2021
ABSTRACT: There has been very little knowledge about the state of gas dispersion in the oxygen delignification process, even though this has a major impact on the performance of the reactor. This paper presents a new continu-ous inline method for measuring oxygen bubble size distribution in the reactor, as well as results from studies con-ducted in softwood and hardwood lines. This new measurement worked well, and new information about oxygen bubble size, as well as how different reactor conditions affected the distribution, was obtained. For example:œ In the softwood line, the mean volume-weighted bubble size was about 0.1 mm, whereas in the hardwood line, this size was almost 10 times higher. For both lines, there was considerable variation in the measured bubble size over the long term.œ For both lines, an increase in mixer rotation speed caused a discernible decrease in the bubble size, and an increase in oxygen charge caused a discernible increase in the bubble size.œ In the softwood line, no coalescence of the bubbles in the reactor was observed, but in the hardwood line, some coalescence of the larger bubbles occurred.œ In the test conducted in the hardwood line, the use of brownstock washer defoamer caused a discernible increase in oxygen bubble size.œ In the hardwood line, reactor pressure had a noticeable effect on the amount of delignification, which indicated that improving mass transfer of oxygen (e.g., by decreasing the oxygen bubble size, in this case) should also have an increasing effect on the delignification.
Journal articles
Magazine articles
The role of gas dispersion in the oxygen delignification process, TAPPI Journal May 2021
ABSTRACT: Oxygen delignification is an essential part of the pulp production process. Delignification occurs with the aid of alkali and dissolved oxygen. Dissolved oxygen is obtained by dispersing oxygen gas into the pulp suspension by using efficient mixers. Little is known about the state of oxygen gas dispersion and its effect on oxygen delignification kinetics and efficiency. This paper will present the results for the effect of gas bubble size on the performance of oxygen delignification. The results are mainly based on detailed studies made in a Finnish hardwood mill where the oxygen bubble size distribution could be altered at the feed of the reactor. An essential aspect of these studies was the use of a new continuous inline gas bubble size measurement system to simultaneously determine the bubble size distribution at the feed and top of the reactor. Information about oxygen consumption in the reactor could also be obtained through the bubble size measurements. Accordingly, these studies quantify the effect of oxygen bubble size on the kappa reduction of the pulp. The effect of different chemical factors on the oxygen bubble size is also studied.Finally, the relationship between the gas bubble size and the liquid phase oxygen mass transfer coefficient (kLa) is presented. This connects the bubble size to the kappa reduction rate. Based on the presented modeling approach and the evaluation of practical factors that are not taken into account in the modeling, it was concluded that the volumetric average oxygen bubble size should preferably be smaller than 0.2 mm in practice.The information obtained with the new gas bubble size measurement system and the presented modeling approach give a very new basis for understanding, monitoring, adjusting, and designing oxygen delignification processes.
Journal articles
Magazine articles
Mechanical modification of softwood pulp fibers using a novel lightweight vertical bar plate, TAPPI Journal April 2021
ABSTRACT: Refiner plates made using sand casting have a draft angle, which results in a trapezoidal bar shape. These trapezoidal bar plates have a limited throughput compared to the vertical bar plates, and eventually the edges of the bars become dull, resulting in longer time to reach the target freeness and shorter service life. The new light-weight refiner plate with a bar insertion method into a plate base was developed by selecting an aluminium-based alloy as the plate base material and a stainless steel alloy with high wear resistance as the bar material. The light-weight plate with sharp bar edges was very effective in reducing refining energy by reaching the target freeness faster than the sand-cast bar plate. Finally, the lightweight sharp bar plate, which weighed only about half the weight of the cast bar plate, was expected to significantly contribute to easy replacement, improved paper quality, and larger throughput without excessive loss of fiber length.
Journal articles
Comparative evaluation of conical and double disk refiners: Effects of operating mode, refining intensity, and device geometry on energy consumption and paper properties, TAPPI Journal August 2026
ABSTRACT: This study investigates the effects of refiner operating mode and refining intensity adjusted via pulp flow rate, applied power, and refiner speed on the refining characteristics of high-yield southern softwood. We compared Valmet’s OptiFiner PRO (conical) and DD6700 (double disk) refiners under matched specific edge load (SEL) conditions. Batch and one-pass modes were evaluated for their impact on energy efficiency and physical paper properties. The results showed that while SEL provides a useful baseline, it does not fully account for differences in refiner geometry, particularly angular parameters. With the chosen plate sets, C-factor analysis revealed that the OptiFiner PRO delivers a lower number of fiber impacts at a higher intensity per impact compared to DD6700 at similar SEL, influencing fiber length, short-span compression test (STFI) index, and tear strength development. These findings offer actionable insights for mills seeking to optimize refining efficiency and cost. In summary, conical refiners may provide advantages in compression strength at mid-range energies, while double disk refiners maintain higher tear strength at elevated energies due to better fiber length preservation.
Journal articles
Simplified modeling of a complete rotary lime kiln at a pulp mill, TAPPI Journal February 2026
ABSTRACT: Rotary lime kilns are essential and complex components in pulp mills using the kraft process. They are primarily used to produce lime (CaO), which is then employed to make white liquor, the reagent used to separate wood fibers. To understand and improve the performance of the kiln, modeling its behavior is essential. However, the kiln operates through a complex combination of thermal and chemical phenomena. That is why a simplified approach was used to tackle this challenge. A zero/one-dimensional steady-state analysis was performed based on first principles to simplify the modeling process and reduce the need for experimental data. Additional assumptions, such as steady-state operation and the absence of a refractory lining, were introduced to further simplify the model so that it can be used for daily analysis. Moreover, the auxiliary equipment of the plant, such as the intercooler and preheat cyclone, is also modeled. The final model was validated using data from the literature and a two-month analysis of experimental measure-ments from the Burgo Ardennes lime kiln in Virton, Belgium. It shows good agreement with the available data, with a 6% deviation for the adiabatic flame temperature and a 17% average error in predicting the kiln shell outside temperature. For the fuel and lime flow rate predictions, also validated over the same two-month period, the errors were -6.6% and 0.6%, respectively.
Journal articles
Magazine articles
Utilization of Areca leaf residues for sustainable production of greyboard, TAPPI Journal May 2024
ABSTRACT: This study primarily focused on the production of greyboard using waste materials from small scale industries, and specifically using Areca leaf waste fibers as a sustainable and environmentally friendly resource. Areca leaf waste fibers were employed as the primary raw material for greyboard manufacturing. The resulting greyboard exhibited commendable properties, including a tear index of 7.53 mN·m2/g, tensile index of 18.34·N·m/g (i.e., breaking length of 1870 m), burst factor of 9.24 (gf/cm2)/(g/m2) and stiffness factor of 33.1. This greyboard was created through a series of steps, including hydrothermal treatment of the material at 155°C and mechanical pulping refinement. The produced greyboard met the specifications outlined in the Indian Standard 2617 (1967) for greyboard. The key objective of this work was to leverage agricultural waste resources to develop a chemical-free greyboard, resulting in reduced waste disposal in open fields and a decrease in chemical usage within the greyboard manufacturing industry. Various characterization techniques, including field emission scanning electron microscopy (FE-SEM), attenuated total reflection•Fourier transform infrared (ATR-FTIR) analysis, and X-ray diffraction (XRD), were used to assess the fiber quality, including aspects such as functional groups, morphology, and crystallinity for the materials used in the manufacturing process.
Journal articles
Magazine articles
Kinetics of sulfur dioxide-alcohol-water (SAW) pulping of su
Kinetics of sulfur dioxide-alcohol-water (SAW) pulping of sugarcane straw (SCS), TAPPI JOURNAL June 2017
Journal articles
Controlling sulfidity by recycling sulfur in CNCG, TAPPI Journal July 2026
ABSTRACT: Pulp and paper mills have faced a major dilemma. On one hand, mills should not dispose of the side streams by mixing them with effluent water. On the other hand, there has been no other way to dispose of excess sulfur than getting rid of recovery boiler electrostatic precipitator (ESP) ash and buying sodium hydroxide to replace lost sodium. A new, yet old, process has been introduced to alleviate the problem. An alternative is the onsite production of sulfuric acid (H2SO4) to significantly reduce, or to even eliminate, the need for recovery boiler fly ash dumping. A sulfuric acid plant produces concentrated commercial quality H2SO4 from concentrated non-condensable gases (CNCGs). Up to 99.9% of the sulfur in CNCGs can be converted into concentrated sulfuric acid with this wet-gas sulfuric acid (WSA) process. There are already references on pulp mills highlighting that the process is straightforward to use. Mills can increase the amount of sulfur in CNCGs by controlling the heavy back liquor storage time and temperature. This opens up a new way to control the mill sulfidity by recycling sulfur. The effect of recycling sulfur is highlighted with reference mills. Due to integrated paper production, the Northern Mill is a large energy consumer, producing mostly softwood-based end products. The Eucalyptus Mill is a large standalone hardwood (eucalyptus) pulp mill where electricity is produced substantially in excess of its own use. As a sample case, lignin production with and without sulfur recycling is presented.
Journal articles
Magazine articles
Addressing production bottlenecks and brownstock washer optimization via a membrane concentration system, TAPPI Journal July 2021
ABSTRACT: Advancements in membrane systems indicate that they will soon be robust enough to concentrate weak black liquor. To date, the economic impact of membrane systems on brownstock washing in kraft mills has not been studied and is necessary to understand the viability of these emerging systems and their best utilization.This study investigated the savings that a membrane system can generate related to brownstock washing. We found that evaporation costs are the primary barrier for mills seeking to increase wash water usage. Without these additional evaporation costs, we showed that our hypothetical 1000 tons/day bleached and brown pulp mills can achieve annual savings of over $1.0 MM when operating at higher dilution factors and fixed pulp production rate. We then investigated the impact of increasing pulp production on mills limited by their equipment. In washer-limited mill examples, we calculated that membrane systems can reduce the annual operating cost for a 7% production increase by 91%. Similarly, in evaporator-limited mill examples, membrane systems can reduce the annual operating cost for a 7% production increase by 86%. These results indicated that membrane systems make a production increase significantly more feasible for these equipment-limited mills.