Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Recovery boiler back-end heat recovery, TAPPI Journal March 2023
ABSTRACT: Sustainability and efficient use of resources are becoming increasingly important aspects in the operation of all industries. Recently, some biomass-fired boilers have been equipped with increasingly complex condensing back-end heat recovery solutions, sometimes also using heat pumps to upgrade the low-grade heat. In kraft recovery boilers, however, scrubbers are still mainly for gas cleaning, with only simple heat recovery solutions. In this paper, we use process simulation software to study the potential to improve the power generation and energy efficiency by applying condensing back-end heat recovery on a recovery boiler. Different configurations are considered, including heat pumps. Potential streams to serve as heat sinks are considered and evaluated. Lowering the recovery boiler flue gas temperature to approximately 65°C significantly decreases the flue gas losses. The heat can be recovered as hot water, which is used to partially replace low-pressure (LP) steam, making more steam available for the condensing steam turbine portion for increased power generation. The results indicate that in a simple condensing plant, some 1%•4% additional electricity could be generated. In a Nordic mill that provides district heating, even more additional electricity generation, up to 6%, could be achieved. Provided the availability of sufficient low-temperature heat sinks to use the recovered heat, as well as sufficient condensing turbine swallowing capacity to utilize the LP steam, the use of scrubbing and possibly upgrading the heat using heat pumps appears potentially useful.
Journal articles
Magazine articles
Non-process elements in the recovery cycle of six Finnish kraft pulp mills, TAPPI Journal March 2023
ABSTRACT: In this work, the aim was to study the distribution and accumulation of the non-process elements (NPEs) in the recovery cycle of Finnish pulp mills and look at whether the geographical location (North vs. South) correlates with the current Finnish NPE levels. In addition, a comparison to older similar Finnish measurements was made with an attempt to analyze the reasons behind differences in the most typical non-process elements, aluminum (Al), silicon (Si), calcium (Ca), phosphorus (P), magnesium (Mg), manganese (Mn), chlorine (Cl), and potassium (K), taking into account the main elements in the white liquor, sodium (Na) and sulfur (S). The extensive laboratory results gained in this study are from seven sampling points at six pulp mills and present analytical data of metal concentrations. The data obtained presents an update to previous NPE studies. The levels found did not statistically differ between North and South Finland. The NPE levels, apart from phosphorus, found in Finnish pulp mills today have not changed considerably compared to the levels in earlier investigations in the 1990s. In the newest data, the phosphorus concentration was consistently higher in the as fired black liquor, electrostatic precipitator (ESP) ash, lime mud, and green liquor than in the previous results. In addition, the levels of Al, Si, Ca, P, and Mg in recovery boiler ESP ash were consistently higher compared to the older results. As the mills start to close their systems more, a stronger accumulation of NPEs can be expected, increasing the likelihood of more operational problems in the process. Further understanding of where the NPEs accumulate and how they can be most effectively removed will be valuable knowledge in the future.
Journal articles
Alternative disposal methods for pulp mill biosludge
ABSTRACT: The chemical pulp production process produces notable amounts of biosludge, mostly in the wastewater treatment system. Biosludge is a problematic waste stream due to its properties, and recently, its amounts have been on the increase. The most used disposal processes are incineration in a bark boiler or a recovery boiler now that landfilling is no longer permitted by legislation in many countries. Incineration of wet sludges with poor drying characteristics decreases the energy efficiency of the process. Biosludge is typically mixed with black liquor in the evaporation plant before feeding to the recovery boiler. Although the recovery boiler is designed to handle challenging fuels, biosludge disposal requires consideration of its behavior during evaporation and accumulation of non-process elements in the recovery cycle. This study discusses the currently used sludge handling methods and presents two novel methods, hydrothermal carbonization and anaerobic digestion, to convert sludge into a usable form. Production of hydrochar or biogas offers new usage possibilities for biosludge and improves the energy efficiency of the mill when the new methods replace incineration. The processes are still developing, and thus their economic feasibility is uncertain; however, depending on the case details, they can be considered promising alternatives to be implemented in the future.
Journal articles
Effects of calcium on sodium salt scaling with the presence of resin acids and fatty acids, TAPPI Journal June 2026
ABSTRACT: Reintroducing tall oil soap or its related products into high dry solids black liquor has been found to reduce sodium salt scaling in falling film evaporators. Aside from resin acids and fatty acids, which are the likely scale inhibitors, calcium is reintroduced into black liquor because of the relatively high calcium content of tall oil soap. One concern is that this increase in calcium content might lead to the formation of additional calcium and sodium scales in evaporators. In this work, we investigated the relationship among trace amounts of calcium, sodium salts, resin acids, and fatty acids in a controlled system using a model salt solution and a benchtop setup. We studied the effects of the calcium carbonate addition and calcium carbonate scales on sodium salt scaling in the presence of resin acids and fatty acids. We found that some calcium carbonate is incorporated in the precipitated sodium crystals, and the suspended sodium crystals become larger and more compact with increasing calcium carbonate concentration. Experiments in the benchtop setup show that precipitating calcium carbonate scale on the heat exchanger does not lead to a higher rate of sodium salt scaling. The solubility of calcium carbonate is not affected by the addition of resin acids and fatty acids. These findings indicate that the reduction in sodium salt scaling through the addition of tall oil soap is primarily related to resin acids and fatty acids, rather than to calcium or to interactions between calcium and mixtures of resin and fatty acids.
Journal articles
Preparation of a vegan leather from mycelium with papermaking method, TAPPI Journal June 2026
ABSTRACT: With growing concern over the environmental impacts of both natural leather and conventional synthetic leathers, the development of sustainable and eco-friendly leather alternatives has become an urgent research priority. In this study, an innovative wet papermaking strategy is proposed to fabricate continuous, homogeneous mycelial sheets from chitin-rich fungal mycelium, mimicking the matrix structure of genuine leather. These mycelial sheets were chemically modified to meet the performance requirements of leather foam layers. Subsequently, the modified mycelial sheets were combined with a substrate fabric to produce a novel mycelium-based leather composite (myco-paper leather) that achieves an excellent balance of mechanical properties and tactile qualities. Experimental results demonstrate that the mycelium-sheet-based leather substitute exhibits remarkable mechanical performance, with a tensile strength of approximately 45 MPa and an elongation at break of about 10.5%. After lamination with the substrate fabric, the composite material shows a tear strength of approximately 16 N, along with a desirable hand feel and surface texture. Following tannic acid tanning, the mycelial sheets also exhibit significant antimicrobial and antifungal properties, forming an inhibition zone of approximately 2 mm against Staphylococcus aureus. Through reinforcement with plant fibers, the developed material attains both strength and flexibility, indicating that the wet papermaking of mycelial sheets is a feasible and scalable approach for producing sustainable leather alternatives. This work not only employs a simple and mature papermaking process to process fungal mycelium but also provides a new conceptual and practical foundation for the large-scale production of bio-based leather substitutes. The findings have significant implications for advancing a low-carbon, sustainable leather industry.
Journal articles
Investigation of the factors contributing to malodorous gases emission during secondary fiber reuse, TAPPI Journal June 2026
ABSTRACT: Malodorous gases are commonly produced during secondary fiber reuse, which is harmful to human health and causes environmental pollution. This paper investigated the influence of fiber type and concentration, temperature, and whitewater concentration on the malodorous gases. The results indicated that, in pulp prepared with fresh water, bleached hardwood kraft pulp (LBKP) did not produce malodorous gases after standing for five days. In contrast, the secondary fiber began to release substantial amounts of total volatile organic compounds (TVOC) on the third day and hydrogen sulfide (H2S) and ammonia (NH3) on the sixth day, and black substances began to appear in the pulp, which proved that the microorganisms began to proliferate. With the increase of the secondary fiber concentration, the release amounts of TVOC, H2S, and NH3 gradually rose, along with the black substances in the pulp. With increased temperature, the release of TVOC increased steadily, while the release of H2S and NH3 reached the maximum at about 45°C, and then began to decline. The decrease of the pulp freeness accelerated the generation of the malodorous gases, but the total release amounts of TVOC, H2S, and NH3 were basically the same. With the increase of white water concentration, the release of TVOC, H2S, and NH3 increased rapidly. When the white water/fresh water was 20 mL/80 mL, the slurry changed from pale yellow to aterrimus on the sixth day. Therefore, microorganisms in the secondary fiber caused pulp deterioration, while white water was the main reason for generating a large amount of malodorous gases.
Journal articles
Magazine articles
Online monitoring of the size distribution of lime nodules in a full-scale operated lime kiln using an in-situ laser triangulation camera, TAPPI Journal June 2024
ABSTRACT: To maximize efficiency of the recausticizing process in a pulp mill, producing a reburned lime with high and consistent reactivity is process critical. Prior investigations have demonstrated a correlation between the reactivity of lime and its nodule size, as well as the dusting behavior of the kiln. Therefore, monitoring the nodule size produced in the lime kiln could be a promising indirect method to measure the performance of the lime kiln. The objective of this investigation was to evaluate the utility of a laser triangulation camera for online monitoring of nodule size distribution for the lime kiln. A series of full-scale trials were performed in a lime kiln of a kraft pulp mill in which a camera was installed at the exit conveyor to analyze the lime discharging from the kiln. The nodule size distribution was analyzed for correlation with the lime temperature, flue gas temperature, and rotational speed of the kiln. The monitoring demonstrated temporal stability, and the results showed that the lime temperature had the most significant effect on the nodule size. The rotational speed of the lime kiln and the flue gas temperature showed limited effect on nodule size, but they had significant impact on the specific energy demand. The overall conclusion of the study is that the camera methodology effectively correlates lime temperature with nodule size distribution, and it advocates for the methods of implementation in automating lime temperature control, facilitating the production of consistently reactive lime at a lower specific energy consumption.
Journal articles
Magazine articles
Modeling the dynamics of evaporator wash cycles, TAPPI Journal July 2024
ABSTRACT: Kraft pulping is a process that utilizes white liquor, composed of sodium sulfide (Na2S) and sodium hydroxide (NaOH), for wood delignification and pulp production. This process involves washing the dissolved organics and spent chemicals from the pulp, resulting in the generation of black liquor. Prior to its use as fuel in the recovery boiler, the black liquor is concentrated in multiple-effect evaporators. During the evaporation process, the inorganic salts present in the liquor become supersaturated and undergo crystallization. Fluctuations in sodium, carbonate, sulfate, and oxalate can give rise to severe sodium salt scaling events, which significantly impact the thermal efficiency of the evaporators, and ultimately, pulp production. Dynamic modeling provides insights into fluctuations in liquor chemistry in the evaporators. The primary objective of this study was to employ dynamic modeling to evaluate the effects of wash liquor recovery from evaporator wash cycles. The dynamics associated with wash cycles encompass variations in the concentrations of salts and solids in the recovered wash liquor, changes in the flow rate of wash liquor recovery, and fluctuations in liquor volume within the liquor tanks. The dynamic model was developed using Matlab Simulink and applied to the evaporation plant of a pulp mill in South America. By utilizing one month of mill process data, the model enabled the evaluation of fluctuations in liquor chemistry due to evaporator wash cycles. The developed model has demonstrated the potential to estimate the concentration of key ions responsible for scaling and to contribute to enhancements in evaporator washing strategies.
Journal articles
Magazine articles
Editorial: TAPPI Standards development: Authors and reviewers are welcome, TAPPI Journal July 2021
ABSTRACT: Readers of TAPPI Journal (TJ) and those involved with R&D and process and product quality will be familiar with TAPPI Standard Test Methods. These test methods are necessary for validating research and ensuring the quality of end products. In addition to test methods, TAPPI also publishes information that isn’t directly related to test methods, such as technical information and definitions, which include specifications, guidelines, and glossaries. All Standards information is developed with the consensus of a technical working group that adheres to set procedures.
Journal articles
Magazine articles
In-situ green synthesis and adsorption on methylene blue of copper-based metal organic framework/cellulose/chitosan (CCTSA/HKUST-1) composite aerogel, TAPPI Journal October 2024
ABSTRACT: In order to explore the application of metal-organic frameworks (MOFs) in environmental and water treatment fields, a new composite aerogel of HKUST-1/cellulose/chitosan (CCTSA/HKUST-1) with better hydrostability was synthesized by an in-situ synthesis method combining covalent cross-linking and solvothermal methods as an efficient adsorbent for methylene blue (MB). The composite aerogel (CCTSA) obtained by covalent cross-linking of cellulose (CE) and chitosan (CTS) exhibited excellent stability under strong acid and solvent-thermal conditions. With the increase of CTS content, it was beneficial to the in-situ synthesis of HKUST-1, as well as to increase the mass loading rate of HKUST-1 to 37.06%, while the Brunauer-Emmett-Teller (BET) specific surface area of CCTSA/HKUST-1 composite aerogel reached 945.123 m2·g-1, which was much higher than that of the CCTSA composite aerogel (14.489 m2·g-1). The CCTSA/ HKUST-1 composite aerogel exhibited excellent adsorption capacity (537.6 mg·g-1) on MB solution, and cyclic adsorption could be achieved. This study proposes a concept of valorization of alkaline peroxide mechanical pulping (APMP) waste liquor to hemicellulose-based hydrogel. This hemicellulose-based hydrogel exhibits a sensitive temperature/pH dual response. Hemicellulose-based hydrogels swell or shrink through the change of hydrogen bond/electrostatic repulsion/charge screening. They also show good water absorption and water retention properties.