Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Impact of fiber structure on edge-wicking of highly-sized paperboard, TAPPI JOURNAL August 2018
Impact of fiber structure on edge-wicking of highly-sized paperboard, TAPPI JOURNAL August 2018
Journal articles
CFD-Based Modeling of Kraft Char Beds â?¢ Part 1: Char Bed Burning Model, TAPPI JOURNAL February 2010
CFD-Based Modeling of Kraft Char Beds • Part 1: Char Bed Burning Model, TAPPI JOURNAL February 2010
Magazine articles
Editor's Note: Bright future for coating at ACFS, TAPPI JOUR
Editor's Note: Bright future for coating at ACFS, TAPPI JOURNAL November 2010
Journal articles
A novel approach to quantify spatial coating-layer formation, TAPPI JOURNAL November 2010
A novel approach to quantify spatial coating-layer formation, TAPPI JOURNAL November 2010
Journal articles
Experimental and theoretical study of the manifold flow in a curtain coater, TAPPI JOURNAL November 2010
Experimental and theoretical study of the manifold flow in a curtain coater, TAPPI JOURNAL November 2010
Journal articles
Use of confocal laser scanning microscopy and a computer model to understand ink cavitation and filamentation, TAPPI JOURNAL October 2010
Use of confocal laser scanning microscopy and a computer model to understand ink cavitation and filamentation, TAPPI JOURNAL October 2010
Journal articles
Influence of oxidation and cationization on the properties of thermomechanical pulp fibers, TAPPI JOURNAL October 2010
Influence of oxidation and cationization on the properties of thermomechanical pulp fibers, TAPPI JOURNAL October 2010
Journal articles
Characterization of spruce thermomechanical pulps at the fiber cell wall level: a method for quantitatively assessing pulp fiber development using Simonsâ?? stain, TAPPI JOURNAL October 2010
Characterization of spruce thermomechanical pulps at the fiber cell wall level: a method for quantitatively assessing pulp fiber development using Simons’ stain, TAPPI JOURNAL October 2010
Journal articles
Editorial: TJ editorial board members review 2013 PEERS, IBBC and Research Forum on Recycling, TAPPI JOURNAL September 2013
Editorial: TJ editorial board members review 2013 PEERS, IBBC and Research Forum on Recycling, TAPPI JOURNAL September 2013
Journal articles
Magazine articles
A novel unit operation to remove hydrophobic contaminants, TAPPI Journal April 2020
ABSTRACT: For mills making paper with recovered fiber, removal of hydrophobic contaminants is essential for trouble-free operation of paper machines. Significant cost savings on paper machine operation can be achieved by reducing deposits, which results in better quality, reduced downtime, increased fiber yield, and reduced energy consumption. Bubble nucleation separation (BNS) is a relatively new process for removing hydrophobic particles. When vacuum is applied to a slurry, dissolved gas bubbles nucleate on hydrophobic particles and drag them to the surface for easy removal. We constructed a 16-L batch unit to evaluate the effect of operating parameters on removal of hydrophobic particles, using statistical design of experiments. These results were used to guide our design of a 16-L continuous unit. We tested this unit on laboratory and mill samples. The removal of 60%•80% of hydrophobic particles was achieved with a low reject rate of < 2%.Following on this success, we built a 200-L pilot unit and tested it in our pilot plant. With promising results there, we installed the pilot unit at a commercial paper recycling mill. Over the course of several mill trials, we showed that it was possible to remove a considerable amount of suspended solids from paper machine white water with less than 2% rejects. Unfortunately, due to the unit only treating 50 L/min and the mill flow being 12000 L/min, we were not able treat a sufficient portion of the white water to know whether a large-scale implementation of BNS would improve paper machine runnability.