Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Kraft recovery boiler operation with splash plate and/or beer can nozzles — a case study, TAPPI Journal Octobr 2021
ABSTRACT: In this work, we study a boiler experiencing upper furnace plugging and availability issues. To improve the situation and increase boiler availability, the liquor spray system was tuned/modified by testing different combinations of splash plate and beer can nozzles. While beer cans are typically used in smaller furnaces, in this work, we considered a furnace with a large floor area for the study. The tested cases included: 1) all splash plate nozzles (original operation), 2) all beer can nozzles, and 3) splash plate nozzles on front and back wall and beer cans nozzles on side walls. We found that operating according to Case 3 resulted in improved overall boiler operation as compared to the original condition of using splash plates only. Additionally, we carried out computational fluid dynamics (CFD) modeling of the three liquor spray cases to better understand the furnace behavior in detail for the tested cases. Model predictions show details of furnace combus-tion characteristics such as temperature, turbulence, gas flow pattern, carryover, and char bed behavior. Simulation using only the beer can nozzles resulted in a clear reduction of carryover. However, at the same time, the predicted lower furnace temperatures close to the char bed were in some locations very low, indicating unstable bed burning. Compared to the first two cases, the model predictions using a mixed setup of splash plate and beer can nozzles showed lower carryover, but without the excessive lowering of gas temperatures close to the char bed.
Journal articles
Magazine articles
Corrosion damage and in-service inspection of retractable sootblower lances in recovery boilers, TAPPI Journal October 2021
ABSTRACT: Several reports of accidents involving serious mechanical failures of sootblower lances in chemical recovery boilers are known in the pulp and paper industry. These accidents mainly consisted of detachment and ejection of the lance tip, or even of the entire lance, to the inside of the furnace, towards the opposite wall. At least one of these cases known to the author resulted in a smelt-water explosion in the boiler.In other events, appreciable damage or near-miss conditions have already been experienced. The risk of catastrophic consequences of the eventual detachment of the lance tip or the complete lance of a recovery boiler soot-blower has caught the attention of manufacturers, who have adjusted their quality procedures, but this risk also needs to be carefully considered by the technical staff at pulp mills and in industry committees.This paper briefly describes the failure mechanisms that prevailed in past accidents, while recommending inspection and quality control policies to be applied in order to prevent further occurrences of these dangerous and costly component failures. Digital radiography, in conjunction with other well known inspection techniques, appears to be an effective means to ensure the integrity of sootblower lances in chemical recovery boilers used in the pulp and paper industry.
Journal articles
Magazine articles
Black liquor evaporator upgrades— life cycle cost analysis, TAPPI Journal March 2021
ABSTRACT: Black liquor evaporation is generally the most energy intensive unit operation in a pulp and paper manufacturing facility. The black liquor evaporators can represent a third or more of the total mill steam usage, followed by the paper machine and digester. Evaporator steam economy is defined as the unit mass of steam required to evaporate a unit mass of water from black liquor (i.e., lb/lb or kg/kg.) The economy is determined by the number of effects in an evaporator train and the system configuration. Older systems use four to six effects, most of which are the long tube vertical rising film type. Newer systems may be designed with seven or even eight effects using falling film and forced circulation crystallization technology for high product solids. The median age of all North American evaporator systems is 44 years. Roughly 25% of the current North American operating systems are 54 years or older. Older systems require more periodic maintenance and have a higher risk of unplanned downtime. Also, older systems have chronic issues with persistent liquor and vapor leaks, shell wall thinning, corrosion, and plugged tubes. Often these issues worsen to the point of requiring rebuild or replacement. When considering the age, technology, and lower efficiency of older systems, a major rebuild or new system may be warranted. The intent of this paper is to review the current state of black liquor evaporator systems in North America and present a basic method for determining whether a major rebuild or new installation is warrant-ed using total life cycle cost analysis (LCCA).
Journal articles
Magazine articles
Impact and feasibility of a membrane pre-concentration step in kraft recovery, TAPPI Journal May 2021
ABSTRACT: Emerging robust membrane systems can perform the first section of black liquor (BL) concentration by separating clean water from the black liquor stream using only mechanical pressure. By doing so, they can reduce the steam and energy required for BL concentration. Because of the high osmotic pressure of strong BL, a membrane system would not replace evaporators but would operate in series, performing the first section of BL concentration. In this work, we use a multi-effect evaporator (MEE) model to quantify the steam and energy savings associated with installing membrane systems of different sizes. When maintaining a constant BL solids throughput, we find that a pulp mill could reduce steam usage in its evaporators by up to 65%. Alternatively, a membrane system could also serve to increase BL throughput of the recovery train. We find that a membrane system capable of concentrating BL to 25% could double the BL solids throughput of a mill’s evaporators at the same steam usage. We also demonstrate that installing a membrane system before an MEE would minimally affect key operating parameters such as steam pressures and BL solids concentrations in each effect. This indicates that installing a membrane pre-concentration system would be nonintrusive to a mill’s operations.
Journal articles
Magazine articles
Recovery boiler back-end heat recovery, TAPPI Journal March 2023
ABSTRACT: Sustainability and efficient use of resources are becoming increasingly important aspects in the operation of all industries. Recently, some biomass-fired boilers have been equipped with increasingly complex condensing back-end heat recovery solutions, sometimes also using heat pumps to upgrade the low-grade heat. In kraft recovery boilers, however, scrubbers are still mainly for gas cleaning, with only simple heat recovery solutions. In this paper, we use process simulation software to study the potential to improve the power generation and energy efficiency by applying condensing back-end heat recovery on a recovery boiler. Different configurations are considered, including heat pumps. Potential streams to serve as heat sinks are considered and evaluated. Lowering the recovery boiler flue gas temperature to approximately 65°C significantly decreases the flue gas losses. The heat can be recovered as hot water, which is used to partially replace low-pressure (LP) steam, making more steam available for the condensing steam turbine portion for increased power generation. The results indicate that in a simple condensing plant, some 1%•4% additional electricity could be generated. In a Nordic mill that provides district heating, even more additional electricity generation, up to 6%, could be achieved. Provided the availability of sufficient low-temperature heat sinks to use the recovered heat, as well as sufficient condensing turbine swallowing capacity to utilize the LP steam, the use of scrubbing and possibly upgrading the heat using heat pumps appears potentially useful.
Journal articles
Magazine articles
Non-process elements in the recovery cycle of six Finnish kraft pulp mills, TAPPI Journal March 2023
ABSTRACT: In this work, the aim was to study the distribution and accumulation of the non-process elements (NPEs) in the recovery cycle of Finnish pulp mills and look at whether the geographical location (North vs. South) correlates with the current Finnish NPE levels. In addition, a comparison to older similar Finnish measurements was made with an attempt to analyze the reasons behind differences in the most typical non-process elements, aluminum (Al), silicon (Si), calcium (Ca), phosphorus (P), magnesium (Mg), manganese (Mn), chlorine (Cl), and potassium (K), taking into account the main elements in the white liquor, sodium (Na) and sulfur (S). The extensive laboratory results gained in this study are from seven sampling points at six pulp mills and present analytical data of metal concentrations. The data obtained presents an update to previous NPE studies. The levels found did not statistically differ between North and South Finland. The NPE levels, apart from phosphorus, found in Finnish pulp mills today have not changed considerably compared to the levels in earlier investigations in the 1990s. In the newest data, the phosphorus concentration was consistently higher in the as fired black liquor, electrostatic precipitator (ESP) ash, lime mud, and green liquor than in the previous results. In addition, the levels of Al, Si, Ca, P, and Mg in recovery boiler ESP ash were consistently higher compared to the older results. As the mills start to close their systems more, a stronger accumulation of NPEs can be expected, increasing the likelihood of more operational problems in the process. Further understanding of where the NPEs accumulate and how they can be most effectively removed will be valuable knowledge in the future.
Journal articles
Assessing lignin content in Nordic hardwood and softwood species using models based on near-infrared (NIR) spectral data and partial least squares regression (PLSR), TAPPI Journal September 2025
ABSTRACT: Continuous kraft cooking digesters face challenges affecting product quality, making it valuable to improve control through advanced techniques like near-infrared (NIR) spectroscopy, model predictive control, and machine learning models. The primary goal of this study was to use NIR spectra to predict the amount of lignin in hardwood and softwood samples. This study investigated the correlation of NIR derivative spectra with the amounts of lignin relative to other constituents, namely cellulose, hemicellulose, and water, in wood chip samples of varying chip sizes and shapes from six Nordic wood species. It employed partial least squares regression (PLSR) on the NIR data to construct a model that predicted the lignin fraction and the relative fraction of acid-soluble lignin. When trained on a group of five wood species, the model achieved a satisfactory predictive ability, striking a balance between a wide range of lignin content and a consistent chemical environment. The accuracy increased further when the model was restricted only to spruce and pine, reflecting the benefits of a more homogenous dataset. Additionally, the optimal number of latent variables was identified as two, indicating that three distinct chemical components — cellulose, lignin and water — can be effectively differentiated using NIR.
Journal articles
Biphasic 1-butanol/water delignification of miscanthus for manufacturing papermaking pulp, TAPPI Journal August 2026
ABSTRACT: Miscanthus has emerged as a promising nonwoody fiber source for papermaking and fiber molding as the world has sought alternatives to wood-based products. A diverse range of chemistries have been explored at the laboratory scale to turn nonwoody biomass into fibers; however, few have been successful at pilot or commercial scales. An emerging organosolv delignification chemistry that has demonstrated previous technical success is butanol/water, having been shown to produce papers with similar properties to other, more conventional chemistries, but offering the benefit of a built-in sugar and lignin coproduct separation. While a range of fiber lengths were achieved (0.45•0.95 mm), addition of sodium hydroxide (NaOH) to the butanol/water delignification chemistry resulted in fiber lengths comparable to commercially available hardwood pulps (0.7•1.0 mm). Lignin concentration was reduced from 19.1 wt% in the raw miscanthus to under 3.5 wt% for most trials. The lowest lignin concentration (2.5 wt%) was achieved at 180°C for 180 min with 50:50 butanol:water and 2 wt% acetic acid. Yet, the high severity of this condition (and similar ones) resulted in a significant truncation of fiber length, which is detrimental for papermaking applications. The highest quality pulp for papermaking was generated at 180°C for 180 min with 50:50 butanol:water and 10 wt% NaOH. This pulp had one of the longest fiber lengths, the highest brightness, and the highest hemicellulose concentration. Thus, butanol/water delignification, especially with NaOH addition, resulted in the successful production of cellulose-rich pulps that have potential in commercial papermaking and fiber molding applications.
Journal articles
Effects of calcium on sodium salt scaling with the presence of resin acids and fatty acids, TAPPI Journal June 2026
ABSTRACT: Reintroducing tall oil soap or its related products into high dry solids black liquor has been found to reduce sodium salt scaling in falling film evaporators. Aside from resin acids and fatty acids, which are the likely scale inhibitors, calcium is reintroduced into black liquor because of the relatively high calcium content of tall oil soap. One concern is that this increase in calcium content might lead to the formation of additional calcium and sodium scales in evaporators. In this work, we investigated the relationship among trace amounts of calcium, sodium salts, resin acids, and fatty acids in a controlled system using a model salt solution and a benchtop setup. We studied the effects of the calcium carbonate addition and calcium carbonate scales on sodium salt scaling in the presence of resin acids and fatty acids. We found that some calcium carbonate is incorporated in the precipitated sodium crystals, and the suspended sodium crystals become larger and more compact with increasing calcium carbonate concentration. Experiments in the benchtop setup show that precipitating calcium carbonate scale on the heat exchanger does not lead to a higher rate of sodium salt scaling. The solubility of calcium carbonate is not affected by the addition of resin acids and fatty acids. These findings indicate that the reduction in sodium salt scaling through the addition of tall oil soap is primarily related to resin acids and fatty acids, rather than to calcium or to interactions between calcium and mixtures of resin and fatty acids.
Journal articles
Preparation of a vegan leather from mycelium with papermaking method, TAPPI Journal June 2026
ABSTRACT: With growing concern over the environmental impacts of both natural leather and conventional synthetic leathers, the development of sustainable and eco-friendly leather alternatives has become an urgent research priority. In this study, an innovative wet papermaking strategy is proposed to fabricate continuous, homogeneous mycelial sheets from chitin-rich fungal mycelium, mimicking the matrix structure of genuine leather. These mycelial sheets were chemically modified to meet the performance requirements of leather foam layers. Subsequently, the modified mycelial sheets were combined with a substrate fabric to produce a novel mycelium-based leather composite (myco-paper leather) that achieves an excellent balance of mechanical properties and tactile qualities. Experimental results demonstrate that the mycelium-sheet-based leather substitute exhibits remarkable mechanical performance, with a tensile strength of approximately 45 MPa and an elongation at break of about 10.5%. After lamination with the substrate fabric, the composite material shows a tear strength of approximately 16 N, along with a desirable hand feel and surface texture. Following tannic acid tanning, the mycelial sheets also exhibit significant antimicrobial and antifungal properties, forming an inhibition zone of approximately 2 mm against Staphylococcus aureus. Through reinforcement with plant fibers, the developed material attains both strength and flexibility, indicating that the wet papermaking of mycelial sheets is a feasible and scalable approach for producing sustainable leather alternatives. This work not only employs a simple and mature papermaking process to process fungal mycelium but also provides a new conceptual and practical foundation for the large-scale production of bio-based leather substitutes. The findings have significant implications for advancing a low-carbon, sustainable leather industry.