Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Kraft pulp viscosity as a predictor of paper strength: Its uses and abuses, TAPPI Journal October 2023
ABSTRACT: For bleached kraft pulps, two factors govern paper strength: the individual fiber strength, and the bond strength that adheres the individual fibers together in the paper matrix. Inherent fiber strength is related to the length of the carbohydrate polymers, also known as the degree of polymerization (DP). Average DP (DP) is inferred by performing pulp viscosity measurements. Under certain circumstances during kraft pulping and bleaching, the average polymer lengths can be shortened, resulting in lower pulp viscosity, and may indicate fiber damage. Fiber damage typically manifests itself as a reduction in tear strength for well-bonded handsheets.This paper will review the literature on how pulp viscosity can predict paper/fiber strength and how it can be used as a diagnostic tool. It can be a means to monitor pulp quality during pulping and bleaching, as well as to alert when such operations approach a critical threshold. However, viscosity losses must be carefully and judiciously analyzed. Like most diagnostic tools, viscosity measurements can be misused and abused, which can lead to incorrect inferences about intrinsic fiber strength. This review will also cover these misuses. The overall goal is to provide the papermaker a better understanding of what pulp viscosity is, how it correlates to potential sheet strength, and what its limitations are. It will be illustrated that when pulp viscosity drops below a critical value, it will indicate an appreciable deterioration in the paper’s tear and tensile strength.
Journal articles
Magazine articles
Preparing prehydrolyzed kraft dissolving pulp via phosphotungstic acid prehydrolysis from grape branches, TAPPI Journal January 2022
ABSTRACT: Dissolving pulp was successful prepared via phosphotungstic acid (PTA) prehydrolysis kraft (PHK) cooking followed by an elementary chlorine-free (ECF) bleaching process from grape branches. The effects of prehydrolysis temperature, reaction time, and PTA concentration that potentially affect the quality of dissolving pulp product on chemical components of pulp were studied via an orthogonal experiment. The structure of lignin was activated during the PTA prehydrolysis phase, and lignin was easily removed during the following cooking process. Thus, relatively mild conditions (140°C, 100 min) can be used in the cooking process. During the prehydrolysis phase, temperature exhibited the most significant influence on the cellulose purity of the obtained pulp fiber, followed by reaction time and PTA concentration. The optimized prehydrolysis conditions were as follows: prehydrolysis temperature, 145°C; reaction time, 75 min; and PTA concentration, 1 wt%. Whether the excessively high prehydrolysis temperature or prolonging the reaction time did not favor the retention of long chain cellulose, the delignification selectivity for the cooking process could not be further improved by excessive PTA loading. Under these prehydrolysis conditions, 94.1% and 29.0% for a-cellulose content and total yield could be achieved after the given cooking and bleaching conditions, respectively. Moreover, the chemical structure and crystal form of cellulose were scarcely changed after PTA prehydrolysis, which could be confirmed by results from Fourier transform infrared (FTIR) spectroscopy and X-ray diffraction (XRD). PTA prehydrolysis could be considered as an alternative method for preparing PHK dissolving pulp under relatively mild cooking conditions.
Journal articles
Magazine articles
Can carbon capture be a new revenue opportunity for the pulp and paper sector?, TAPPI Journal August 2021
ABSTRACT: Transition towards carbon neutrality will require application of negative carbon emission technologies (NETs). This creates a new opportunity for the industry in the near future. The pulp and paper industry already utilizes vast amounts of biomass and produces large amounts of biogenic carbon dioxide. The industry is well poised for the use of bioenergy with carbon capture and storage (BECCS), which is considered as one of the key NETs. If the captured carbon dioxide can be used to manufacture green fuels to replace fossil ones, then this will generate a huge additional market where pulp and paper mills are on the front line. The objective of this study is to evaluate future trends and policies affecting the pulp and paper industry and to describe how a carbon neutral or carbon negative pulp and paper production process can be viable. Such policies include, as examples, price of carbon dioxide allowances or support for green fuel production and BECCS implementation. It is known that profitability differs depending on mill type, performance, energy efficiency, or carbon dioxide intensity. The results give fresh understanding on the potential for investing in negative emission technologies. Carbon capture or green fuel production can be economical with an emission trade system, depending on electricity price, green fuel price, negative emission credit, and a mill’s emission profile. However, feasibility does not seem to evidently correlate with the performance, technical age, or the measured efficiency of the mill.
Journal articles
Magazine articles
Recovery boiler back-end heat recovery, TAPPI Journal March 2023
ABSTRACT: Sustainability and efficient use of resources are becoming increasingly important aspects in the operation of all industries. Recently, some biomass-fired boilers have been equipped with increasingly complex condensing back-end heat recovery solutions, sometimes also using heat pumps to upgrade the low-grade heat. In kraft recovery boilers, however, scrubbers are still mainly for gas cleaning, with only simple heat recovery solutions. In this paper, we use process simulation software to study the potential to improve the power generation and energy efficiency by applying condensing back-end heat recovery on a recovery boiler. Different configurations are considered, including heat pumps. Potential streams to serve as heat sinks are considered and evaluated. Lowering the recovery boiler flue gas temperature to approximately 65°C significantly decreases the flue gas losses. The heat can be recovered as hot water, which is used to partially replace low-pressure (LP) steam, making more steam available for the condensing steam turbine portion for increased power generation. The results indicate that in a simple condensing plant, some 1%•4% additional electricity could be generated. In a Nordic mill that provides district heating, even more additional electricity generation, up to 6%, could be achieved. Provided the availability of sufficient low-temperature heat sinks to use the recovered heat, as well as sufficient condensing turbine swallowing capacity to utilize the LP steam, the use of scrubbing and possibly upgrading the heat using heat pumps appears potentially useful.
Journal articles
Magazine articles
Non-process elements in the recovery cycle of six Finnish kraft pulp mills, TAPPI Journal March 2023
ABSTRACT: In this work, the aim was to study the distribution and accumulation of the non-process elements (NPEs) in the recovery cycle of Finnish pulp mills and look at whether the geographical location (North vs. South) correlates with the current Finnish NPE levels. In addition, a comparison to older similar Finnish measurements was made with an attempt to analyze the reasons behind differences in the most typical non-process elements, aluminum (Al), silicon (Si), calcium (Ca), phosphorus (P), magnesium (Mg), manganese (Mn), chlorine (Cl), and potassium (K), taking into account the main elements in the white liquor, sodium (Na) and sulfur (S). The extensive laboratory results gained in this study are from seven sampling points at six pulp mills and present analytical data of metal concentrations. The data obtained presents an update to previous NPE studies. The levels found did not statistically differ between North and South Finland. The NPE levels, apart from phosphorus, found in Finnish pulp mills today have not changed considerably compared to the levels in earlier investigations in the 1990s. In the newest data, the phosphorus concentration was consistently higher in the as fired black liquor, electrostatic precipitator (ESP) ash, lime mud, and green liquor than in the previous results. In addition, the levels of Al, Si, Ca, P, and Mg in recovery boiler ESP ash were consistently higher compared to the older results. As the mills start to close their systems more, a stronger accumulation of NPEs can be expected, increasing the likelihood of more operational problems in the process. Further understanding of where the NPEs accumulate and how they can be most effectively removed will be valuable knowledge in the future.
Journal articles
Assessing lignin content in Nordic hardwood and softwood species using models based on near-infrared (NIR) spectral data and partial least squares regression (PLSR), TAPPI Journal September 2025
ABSTRACT: Continuous kraft cooking digesters face challenges affecting product quality, making it valuable to improve control through advanced techniques like near-infrared (NIR) spectroscopy, model predictive control, and machine learning models. The primary goal of this study was to use NIR spectra to predict the amount of lignin in hardwood and softwood samples. This study investigated the correlation of NIR derivative spectra with the amounts of lignin relative to other constituents, namely cellulose, hemicellulose, and water, in wood chip samples of varying chip sizes and shapes from six Nordic wood species. It employed partial least squares regression (PLSR) on the NIR data to construct a model that predicted the lignin fraction and the relative fraction of acid-soluble lignin. When trained on a group of five wood species, the model achieved a satisfactory predictive ability, striking a balance between a wide range of lignin content and a consistent chemical environment. The accuracy increased further when the model was restricted only to spruce and pine, reflecting the benefits of a more homogenous dataset. Additionally, the optimal number of latent variables was identified as two, indicating that three distinct chemical components — cellulose, lignin and water — can be effectively differentiated using NIR.
Journal articles
Optimization of energy efficiency and condensate production in evaporation plants for a modern softwood pulp mill, TAPPI Journal April 2026
ABSTRACT: To meet the need to further improve thermal efficiency and environmental performance of kraft pulp mills, new systems and techniques have been developed within the evaporation plant. This paper describes these novel approaches and how they were implemented in a project completed in 2018 for a new evaporator and condensate treatment system supplied by Valmet at the SCA Östrand market pulp mill in Sweden. This project was part of a stepwise upgrade of the complete mill to increase the production capacity of the mill from 430,000 to 900,000 air-dried metric tons/year (ADt/y). As part of this upgrade, the mill had the objectives to increase the energy efficiency of the pulp mill and to minimize the air emissions as much as possible, the effluent volume, and the water usage in the mill. The mill also wanted to have the disposal of the biosludge in the black liquor, and the production of tall oil from black liquor soap, liquid methanol, and turpentine. This required that the new evaporation and condensate treatment system be very closely integrated into the other process departments of the mill, including integration of the hot weak black liquor flash vapor from the digester directly into the evaporator train and the production of multiple streams of clean evaporation plant condensate at the correct temperature for the bleach plant. Heat and mass balance calculation values, which were found to do very well in predicting the effect on actual mill operation, are also presented in this paper.
Journal articles
Biphasic 1-butanol/water delignification of miscanthus for manufacturing papermaking pulp, TAPPI Journal August 2026
ABSTRACT: Miscanthus has emerged as a promising nonwoody fiber source for papermaking and fiber molding as the world has sought alternatives to wood-based products. A diverse range of chemistries have been explored at the laboratory scale to turn nonwoody biomass into fibers; however, few have been successful at pilot or commercial scales. An emerging organosolv delignification chemistry that has demonstrated previous technical success is butanol/water, having been shown to produce papers with similar properties to other, more conventional chemistries, but offering the benefit of a built-in sugar and lignin coproduct separation. While a range of fiber lengths were achieved (0.45•0.95 mm), addition of sodium hydroxide (NaOH) to the butanol/water delignification chemistry resulted in fiber lengths comparable to commercially available hardwood pulps (0.7•1.0 mm). Lignin concentration was reduced from 19.1 wt% in the raw miscanthus to under 3.5 wt% for most trials. The lowest lignin concentration (2.5 wt%) was achieved at 180°C for 180 min with 50:50 butanol:water and 2 wt% acetic acid. Yet, the high severity of this condition (and similar ones) resulted in a significant truncation of fiber length, which is detrimental for papermaking applications. The highest quality pulp for papermaking was generated at 180°C for 180 min with 50:50 butanol:water and 10 wt% NaOH. This pulp had one of the longest fiber lengths, the highest brightness, and the highest hemicellulose concentration. Thus, butanol/water delignification, especially with NaOH addition, resulted in the successful production of cellulose-rich pulps that have potential in commercial papermaking and fiber molding applications.
Journal articles
Alternative disposal methods for pulp mill biosludge
ABSTRACT: The chemical pulp production process produces notable amounts of biosludge, mostly in the wastewater treatment system. Biosludge is a problematic waste stream due to its properties, and recently, its amounts have been on the increase. The most used disposal processes are incineration in a bark boiler or a recovery boiler now that landfilling is no longer permitted by legislation in many countries. Incineration of wet sludges with poor drying characteristics decreases the energy efficiency of the process. Biosludge is typically mixed with black liquor in the evaporation plant before feeding to the recovery boiler. Although the recovery boiler is designed to handle challenging fuels, biosludge disposal requires consideration of its behavior during evaporation and accumulation of non-process elements in the recovery cycle. This study discusses the currently used sludge handling methods and presents two novel methods, hydrothermal carbonization and anaerobic digestion, to convert sludge into a usable form. Production of hydrochar or biogas offers new usage possibilities for biosludge and improves the energy efficiency of the mill when the new methods replace incineration. The processes are still developing, and thus their economic feasibility is uncertain; however, depending on the case details, they can be considered promising alternatives to be implemented in the future.
Journal articles
Effects of calcium on sodium salt scaling with the presence of resin acids and fatty acids, TAPPI Journal June 2026
ABSTRACT: Reintroducing tall oil soap or its related products into high dry solids black liquor has been found to reduce sodium salt scaling in falling film evaporators. Aside from resin acids and fatty acids, which are the likely scale inhibitors, calcium is reintroduced into black liquor because of the relatively high calcium content of tall oil soap. One concern is that this increase in calcium content might lead to the formation of additional calcium and sodium scales in evaporators. In this work, we investigated the relationship among trace amounts of calcium, sodium salts, resin acids, and fatty acids in a controlled system using a model salt solution and a benchtop setup. We studied the effects of the calcium carbonate addition and calcium carbonate scales on sodium salt scaling in the presence of resin acids and fatty acids. We found that some calcium carbonate is incorporated in the precipitated sodium crystals, and the suspended sodium crystals become larger and more compact with increasing calcium carbonate concentration. Experiments in the benchtop setup show that precipitating calcium carbonate scale on the heat exchanger does not lead to a higher rate of sodium salt scaling. The solubility of calcium carbonate is not affected by the addition of resin acids and fatty acids. These findings indicate that the reduction in sodium salt scaling through the addition of tall oil soap is primarily related to resin acids and fatty acids, rather than to calcium or to interactions between calcium and mixtures of resin and fatty acids.