Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Non-process elements in the lime cycle: New findings regarding NPE distribution and lime mud filterability, TAPPI Journal July 2026
ABSTRACT: Proper functioning of the recausticizing cycle is crucial for securing a stable white liquor supply for a pulp mill. Common runnability problems in the modern lime cycle, such as low filterability and poor dewatering of lime mud, high dead load, or ring formation in the lime kiln, are often caused by accumulation of non-process elements (NPEs). This project attempted to verify the traditional rules of thumb regarding the chemical behavior of NPEs: magnesium (Mg), aluminum (Al), silicon (Si), phosphorus (P), zinc (Zn), manganese (Mn), iron (Fe), copper (Cu), barium (Ba), cadmium (Cd), and lead (Pb) in the causticizing reaction, and to investigate the reasons behind poor lime mud filterability. First, a standardized method for measuring filterability of lime mud was developed. Next, a series of recausticizing experiments, followed by immediate filtration trials, was conducted using mill green liquors, laboratory-made synthetic green liquor, reburned lime/makeup mix, and extra NPE additions. It was found that sodium (Na), potassium (K), and sulfur (S) followed the liquid phase, as expected, while Mg, P, and Ba, but also Pb, Cu, and Cd, showed low solubility and accumulated in the lime mud. The Si and Al accumulated in the lime mud even though the soluble content in liquor was high, while the behavior of Mn, Fe, and Zn was more complex. Based on these results, tentative solubility limits for NPEs were suggested as a first estimate for the maximum possible concentrations of NPEs in mill white liquor. The causticization-filtration experiments revealed that overliming and high content of Mg in green liquor clearly led to lower filterability, but our addition of Si did not have such an effect. As differences in particle size and size distribution have a certain impact on the filtration resistance, the lime mud sedimentation behavior, combined with other characterization methods, might be used as an indication for the filterability. Finally, a list of recommendations for pulp mills was formulated that starts with establishing a comprehensive standard for a lime mud with good filterability. This standard can be used as a benchmark for comparison any time a lime cycle runnability problem is identified.
Journal articles
Black liquor spray properties in-furnace conditions for swirl cone nozzles, TAPPI Journal July 2026
ABSTRACT: Recovery boiler furnace operation is controlled for high chemical recovery, high steam production, and low emissions. Good control allows long runs with minimum cleaning without expensive shutdowns. An essential variable affecting boiler operation is black liquor spraying into the furnace. Poorly controlled black liquor spraying causes difficulties, e.g., in chemical recovery, fouling of heat transfer surfaces, and decreased energy production. A challenging measurement strategy with three different swirl cone nozzles . types A, C, and T . was carried out at a mill in the United States. Black liquor spray properties were measured under in-furnace conditions for flow rates of 2.0 L/s to 3.0 L/s. Three spraying temperatures of 119™‹C, 122™‹C, and 126™‹C, which were 2™‹C, 5™‹C, and 9™‹C above the boiling point (ƒ¢Te), were tested. These flow rates and temperatures are typical for industrial nozzle sizes with exit orifice sizes of 17 mm and 22 mm. An imaging method to measure droplet size in a highly challenging furnace environment was developed. Droplet volume median diameter (Dv50) for nozzles A, C, and T varied between 7 mm to 4 mm, 7 mm to 5 mm, and 8 mm to 6 mm, depending on the flow rate and temperature. The high number of droplets detected by the analysis program enabled data fitting into statistical correlations. The size and width parameters for the Rosin™]Rammer droplet size distribution function could be defined. The droplet size distribution was found to be surprisingly wide, probably because of swollen droplets. Spray velocity was measured in two locations, 5 cm from the nozzle and 1.8 m from the nozzle. Near the nozzle, the average velocity increased from 7.3 m/s to 13 m/s when the flow rate was increased from 2 L/s to 3 L/s. Increase of black liquor temperature increased spray velocity in most of the cases. At the distance of 1.8 m from the nozzle, average spray velocities varied between 4.0 m/s to 11 m/s, depending on nozzle geometry, flow rate, and temperature. The opening angles of the spray for nozzles A and C varied between 57™‹ to 78™‹. The opening angle of nozzle T with flow guide varied between 48™‹ to 56™‹. The highest penetration of the spray was estimated for nozzle T because of the narrow spray and large droplets.
Journal articles
Magazine articles
Evaluation of soap recovery efficiency from black liquor — analytical tools, TAPPI Journal April 2023
ABSTRACT: Soap skimmings (“soap”) are typically recovered from black liquor in kraft mills that process a high percentage of softwood. In many mills, the recovery of soap is inefficient, negatively impacting performance of evaporators and recovery boilers and resulting in loss of potential revenue. A thorough evaluation of soap recovery performance in a kraft mill requires measurement of soap content in black liquor at various sampling locations, especially around the soap skimmer.The standard laboratory method for evaluating soap content in black liquor is a complex, multi-step process that relies on solvent extraction and titration; most mills send these samples to an outside laboratory for this analysis. In this study, 100 black liquor samples, with a wide range of soap concentrations, were tested by the standard solvent extraction method. After additional dilution, each sample was also tested for surface tension with a bubble pressure tensiometer. The results were found to correlate very closely with the solvent extraction tests results. This alternate method, using surface tension measurements of diluted black liquor samples, produces rapid results and can be easily implemented in most kraft mills, which would facilitate much more frequent in-house evaluations of soap recovery performance.
Journal articles
Magazine articles
Advantages of lean duplex stainless steels in the pulp and paper industry, TAPPI Journal April 2023
ABSTRACT: The performance of lean duplex stainless steels has been utilized by the pulp and paper industry since their introduction to the market almost 20 years ago. Experience has shown that this group of stainless steels has exceptional performance in, for example, alkaline environments towards typical deterioration mechanisms, i.e., uniform corrosion and stress corrosion cracking. The chemistry of the “lean” duplex steels is designed so that the content of volatile and expensive elements like nickel and molybdenum can be reduced to an absolute minimum without sacrificing the technical performance. This reduces the raw material cost and most importantly provides predictability of the steel price, which is often challenging with conventional austenitic and duplex stainless steels.Thanks to a dual phase microstructure and high nitrogen content, lean duplex steels have at least two times higher strength compared to standard austenitic stainless steels. This is often a preferred feature in pulp and paper construction, as it enables lighter structures and less material to be utilized. Today, lean duplex steels are widely available in various dimensions, from thin cold rolled sheets up to thick hot rolled plates. Lean duplex steels are also fully recyclable after the decommissioning stage of the equipment, thereby contributing to the circular economy.
Journal articles
Magazine articles
Economic and competitive potential of lignin-based thermoplastics using a multicriteria decision-making method, TAPPI Journal September 2022
ABSTRACT: As a result of new lignin extraction plants hatching and increasing volumes of technical lignin becoming available, a variety of lignin derivatives, including phenolic resins and polyurethane (PU) foams, are reaching the marketplace or being used as intermediate products in many industrial applications. In the spectrum of possible lignin derivatives, thermoplastics appear particularly attractive due to a symbiosis of market, policy, and technology drivers. To assess the preferredness for lignin-based thermoplastics, this paper adapted a risk-oriented methodology formerly applied to assess lignin usage in various applications (phenol-formaldehyde [PF] resins, PU foams, and carbon fiber applications) to the case of lignin-based thermoplastics using hydroxypropylated lignin (HPL) and miscible blends of lignin and polyethylene oxide (PEO). The HPL is considered for garbage bags and agricultural films applications, while lignin-PEO blends are used as replacement for acrylonitrile butadiene styrene (ABS) in applications such as automotive parts. In the methodology, two phased-implementation strategies were defined for each thermoplastic derivative, considering perspectives for profit maximization (90 metric tons/day integrated units) and revenue growth (350 metric tons/day overall capacity), which were considered for implementation within a softwood kraft pulping mill. A set of six criteria representative of the main economic and market competitiveness issues were employed, and their respective importance weights were obtained in a multicriteria decision-making (MCDM) panel.Early-stage techno-economic estimates were done as a basis for the calculation of decision criteria. Compared to product derivatives previously assessed, capital investment for thermoplastic strategies appeared marginally higher due to the required lignin modification steps (on average 30% higher at similar capacity, and 6% for higher-scale revenue diversification strategies). Higher operating costs were also observed due to increased chemical expenses for all thermoplastic strategies, which are ultimately balanced by revenues associated with targeted thermoplastic products, leading to greater annual margins and cash flow generation over the project lifetime for thermoplastic strategies compared to other product applications (58% to 66% higher on average, at similar scale). Benefits of improved economics were reflected in economic criteria, internal rate of return (IRR), and cash flow on capital employed (CFCE), as well as in the price competitiveness criterion, CPC. Overall, the combination of relatively high lignin content in the plastic formulation and the less costly modification method contributed to lignin-PEO strategies, gaining the top two rankings. Based on their overall scores, both strategies defined for HPL would also integrate the group of “preferred” strategies, but are outranked by strategies that consider lignin positioning on PU foam applications.
Journal articles
Magazine articles
Understanding the risks and rewards of using 50% vs. 10% strength peroxide in pulp bleach plants,TAPPI Journal December 2024
Authors: Alan W. Rudie and Peter W. Hart | TAPPI J. 17(11): 601(2018) - ABSTRACT: The use of 50% concentration and 10% concentration hydrogen peroxide were evaluated for chemical and mechanical pulp bleach plants at storage and at point of use. Several dangerous occurrences have been documented when the supply of 50% peroxide going into the pulping process was not stopped during a process failure. Startup conditions and leaking block valves during maintenance outages have also contributed to explosions. Although hazardous events have occurred, 50% peroxide can be stored safely with proper precautions and engineering controls. For point of use in a chemical bleach plant, it is recommended to dilute the peroxide to 10% prior to application, because risk does not outweigh the benefit. For point of use in a mechanical bleach plant, it is recommended to use 50% peroxide going into a bleach liquor mixing system that includes the other chemicals used to maintain the brightening reaction rate. When 50% peroxide is used, it is critical that proper engineering controls are used to mitigate any risks.
Journal articles
Magazine articles
Experiments and visualization of sprays from beer can and turbo liquor nozzles, TAPPI Journal February 2022
ABSTRACT: Industrial scale swirl-type black liquor nozzles were studied using water as the test fluid. Simple water spraying experiments were found to be very beneficial for studying and comparing nozzles for black liquor spraying. These kinds of experiments are important for finding better nozzle designs. Three nozzle designs were investigated to understand the functional differences between these nozzles. The pressure loss of nozzle 1 (“tangential swirl”) and nozzle 3 (“turbo”) were 97% and 38% higher compared to nozzle 2 (“tan-gential swirl”). Spray opening angles were 75°, 60°, and 35° for nozzles 1, 2, and 3, respectively. Video imaging showed that the nozzles produced sprays that were inclined a few degrees from the nozzle centerline. Spray patter-nation showed all the sprays to be asymmetric, while nozzle 2 was the most symmetric. Laser-Doppler measure-ments showed large differences in spray velocities between nozzles. The spray velocity for nozzle 1 increased from 9 m/s to 15 m/s when the flow rate was increased from 1.5 L/s to 2.5 L/s. The resulting velocity increase for nozzle 2 was from 7 m/s to 11 m/s, and for nozzle 3, it was from 8 m/s to 13 m/s. Tangential flow (swirl) directed the spray 6°–12° away from the vertical plane. Liquid sheet breakup mechanisms and lengths were estimated by analyzing high speed video images. The liquid sheet breakup mechanism for nozzle 1 was estimated to be wave formation, and the sheet length was estimated to be about 10 cm. Sheet breakup mechanisms for nozzle 2 were wave formation and sheet perforation, and the sheet length was about 20 cm. Nozzle 3 was not supposed to form a liquid sheet. Nozzle geometry was found to greatly affect spray characteristics.
Journal articles
Magazine articles
Control of malodorous gases emission from wet-end white water with hydrogen peroxide, TAPPI Journal October 2021
ABSTRACT: White water is highly recycled in the papermaking process so that its quality is easily deteriorated, thus producing lots of malodorous gases that are extremely harmful to human health and the environment. In this paper, the effect of hydrogen peroxide (H2O2) on the control of malodorous gases released from white water was investigated. The results showed that the released amount of total volatile organic compounds (TVOC) decreased gradually with the increase of H2O2 dosage. Specifically, the TVOC emission reached the minimum as the H2O2 dosage was 1.5 mmol/L, and meanwhile, the hydrogen sulfide (H2S) and ammonia (NH3) were almost completely removed. It was also found that pH had little effect on the release of TVOC as H2O2 was added, but it evidently affect-ed the release of H2S and NH3. When the pH value of the white water was changed to 4.0 or 9.0, the emission of TVOC decreased slightly, while both H2S and NH3 were completely removed in both cases. The ferrous ions (Fe2+) and the copper ions (Cu2+) were found to promote the generation of hydroxyl radicals (HO•) out of H2O2, enhancing its inhibition on the release of malodorous gases from white water. The Fe2+/H2O2 system and Cu2+/H2O2 system exhibited similar efficiency in inhibiting the TVOC releasing, whereas the Cu2+/H2O2 system showed better perfor-mance in removing H2S and NH3.
Journal articles
Magazine articles
Production of antimicrobial paper using nanosilver, nanocellulose, and chitosan from a coronavirus perspective, TAPPI Journal July 2021
ABSTRACT: The pulp and paper industry has an opportunity to play a vital role in breaking the spread of the COVID-19 pandemic through production that supports widespread use of antimicrobial paper. This paper provides a brief review of paper and paper-related industries, such as those producing relevant additives, and R&D organizations that are actively engaged in developing antimicrobial papers. The focus here is on the potential of three nano-additives for use in production of antimicrobial papers that combat coronavirus: nanosilver, nanocellulose, and chitosan. Various recent developments in relevant areas and concepts underlining the fight against coronavirus are also covered, as are related terms and concepts.
Journal articles
Magazine articles
Addressing production bottlenecks and brownstock washer optimization via a membrane concentration system, TAPPI Journal July 2021
ABSTRACT: Advancements in membrane systems indicate that they will soon be robust enough to concentrate weak black liquor. To date, the economic impact of membrane systems on brownstock washing in kraft mills has not been studied and is necessary to understand the viability of these emerging systems and their best utilization.This study investigated the savings that a membrane system can generate related to brownstock washing. We found that evaporation costs are the primary barrier for mills seeking to increase wash water usage. Without these additional evaporation costs, we showed that our hypothetical 1000 tons/day bleached and brown pulp mills can achieve annual savings of over $1.0 MM when operating at higher dilution factors and fixed pulp production rate. We then investigated the impact of increasing pulp production on mills limited by their equipment. In washer-limited mill examples, we calculated that membrane systems can reduce the annual operating cost for a 7% production increase by 91%. Similarly, in evaporator-limited mill examples, membrane systems can reduce the annual operating cost for a 7% production increase by 86%. These results indicated that membrane systems make a production increase significantly more feasible for these equipment-limited mills.