Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Event Type
Collections
Journal articles
Magazine articles
Improving paper wet strength via increased lignin content and hot-pressing temperature, TAPPI JOURNAL October 2020
ABSTRACT: It is known that the strength properties of wood-based paper materials can be enhanced via hot-pressing techniques. Today, there is a desire not only for a change from fossil-based packaging materials to new sustainable bio-based materials, but also for more effective and eco-friendly solutions for improving the dry and wet strength of paper and board. Against this background, hot pressing of paper made from high yield pulp (HYP), rich in lignin, becomes highly interesting. This study investigated the influence of pressing temperature and native lignin content on the properties of paper produced by means of hot pressing. Kraft pulps of varied lignin content (kappa numbers: 25, 50, 80) were produced at pilot scale from the same batch by varying the cooking time. We then studied the effect of lignin content by evaluating the physical properties of Rapid Köthen sheets after hot pressing in the temperature range of 20°C•200°C with a constant nip pressure of 7 MPa. The pilot-scale cooked pulps were compared with reference samples of mill-produced northern bleached soft-wood kraft (NBSK) pulp and mill-produced chemithermomechanical pulp (CTMP).Generally, the results demonstrated that lignin content had a significant effect on both dry and wet tensile index. All of the pilot cooked pulps with increased lignin content had a higher tensile index than the reference NBSK pulp. To obtain high tensile index, both dry and wet, the pressing temperature should be set high, preferably at least 200°C; that is, well above the glass transition temperature (Tg) for lignin. Moreover, the lignin content should prefera-bly also be high. All kraft pulps investigated in this study showed a linear relationship between wet strength and lignin content.
Journal articles
Magazine articles
Crossflow filtration of green liquor for increased pulp production, improved green liquor quality, and energy savings, TAPPI JOURNAL October 2020
ABSTRACT: A new green liquor filtration system has been installed and commissioned at the Ence pulp mill in Pontevedra, Spain. The filtration system is based on microfiltration and was developed in collaboration with the KTH Royal Institute of Technology in Stockholm, Sweden. The patented method for efficient purification of green liquor decreases the non-process element (NPE) content by providing more efficient solids/liquid separation, reducing energy and chemical consumption in pulp mills and increasing production capacity by eliminating certain capacity bottlenecks. The process has been continuously tested at the Aspa Bruk Mill outside Askersund, Sweden, since 2013. The technology has proven to create nearly particulate-free green liquor during the purification process. The technology can also be used to polish white liquor to provide higher pulp quality.To provide for a simple and cost-effective installation, the system was designed as a skid-mounted unit that is pre-piped, instrumented, and tested before shipment. The system is modular and allows for easy expansion of capacity. This paper discusses the process design, process integration, and startup of the new system, along with experiences from the first months of operation.
Journal articles
Magazine articles
Mechanical modification of softwood pulp fibers using a novel lightweight vertical bar plate, TAPPI Journal April 2021
ABSTRACT: Refiner plates made using sand casting have a draft angle, which results in a trapezoidal bar shape. These trapezoidal bar plates have a limited throughput compared to the vertical bar plates, and eventually the edges of the bars become dull, resulting in longer time to reach the target freeness and shorter service life. The new light-weight refiner plate with a bar insertion method into a plate base was developed by selecting an aluminium-based alloy as the plate base material and a stainless steel alloy with high wear resistance as the bar material. The light-weight plate with sharp bar edges was very effective in reducing refining energy by reaching the target freeness faster than the sand-cast bar plate. Finally, the lightweight sharp bar plate, which weighed only about half the weight of the cast bar plate, was expected to significantly contribute to easy replacement, improved paper quality, and larger throughput without excessive loss of fiber length.
Journal articles
Magazine articles
Application of fuzzy TOPSIS in the Analyze phase of the DMAIC cycle to aid decision-making, TAPPI Journal April 2020
ABSTRACT: This paper reports the use of multicriteria analysis in the Analyze phase of the DMAIC (Define-Measure-Analyze-Improve-Control) cycle for continuous improvement. The research was carried out in a tissue paper factory located in southern Brazil. A sample of 64 parts of 16 different reels of recycled paper was used. A problem regarding paper quality variability was detected, presenting a scrap index ranging between 9% and 23%, compromising machine productivity and product sales. This motivated the implementation of a structured project supported by the application of the DMAIC cycle. The project team (machine operators, maintenance staff, supervisor, and data analyst) defined the evaluation criteria and determined the control intervals and their equivalence with linguistic variables to support the necessary evaluations for the application of fuzzy TOPSIS (Technique for Order of Preference by Similarity to Ideal Solution). The criteria were C1-Longitudinal Strength (Kgf), C2-Longitudinal Elongation (mm), C3-Cross-strength (kgf), C4-Cross-elongation (mm), C5-Weight (g/m²), and C6-Humidity (%). The results showed that samples with the same ranking had the lowest scrap indexes in the subsequent process. Also, the criterion C5 had a more significant impact on the quality of the product than the other criteria, which was determined from the DMAIC sequence. Improvements related to C5 should be prioritized. The fuzzy TOPSIS method presented is a flexible tool, adapting itself to the solution of the problem and contributing to the decision-making process.
Journal articles
Magazine articles
Guest Editorial: Still working (overtime): Life-saving nonwovens and continued innovation, TAPPI Journal August 2021
ABSTRACT: Recently, the United States federal government has recommended the need for a booster shot to combat COVID-19, highlighting the highly contagious nature of its Delta variant. This variant is surging in countries as far apart as Thailand, Brazil, and the United States. While the availability of the vaccine is not an issue in the United States, African, Latin American, and South Asian countries are in dire need of the vaccine. This scenario necessitates the need for continued safety measures. Among the recommended safety measures, use of face masks has been proven to be effective. Recent analysis showed that two-thirds of the 32 states in the United States with face mask mandates found them helpful for lowering infection rates.
Base Sheet Structures that Control Coating Uniformity: Effects of Length Scale, 2008 Advanced Coating Fundamentals Symposium
Base Sheet Structures that Control Coating Uniformity: Effects of Length Scale, 2008 Advanced Coating Fundamentals Symposium
Effects of the Partial Replacement of SB latex with Dextrin Starch on the Thickness Distribution of Coating Layers, 2008 Advanced Coating Fundamentals Symposium
Effects of the Partial Replacement of SB latex with Dextrin Starch on the Thickness Distribution of Coating Layers, 2008 Advanced Coating Fundamentals Symposium
PREDICTION OF COATING STRUCTURE CHANGE DURING CALENDERING, 2008 Advanced Coating Fundamentals Symposium
PREDICTION OF COATING STRUCTURE CHANGE DURING CALENDERING, 2008 Advanced Coating Fundamentals Symposium
MODELING THE COMPRESSION OF PARTICLE PACKINGS USING THE DISCRETE ELEMENT METHOD, 2008 Advanced Coating Fundamentals Symposium
MODELING THE COMPRESSION OF PARTICLE PACKINGS USING THE DISCRETE ELEMENT METHOD, 2008 Advanced Coating Fundamentals Symposium
Measurement and Modelling of Heat Transfer in Paper Coating Structures, 2008 Advanced Coating Fundamentals Symposium
Measurement and Modelling of Heat Transfer in Paper Coating Structures, 2008 Advanced Coating Fundamentals Symposium