Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Collections
Journal articles
Magazine articles
Kraft pulp bleaching with a P-stage catalyzed by both bicarbonate and TAED, TAPPI Journal July 2019
ABSTRACT: Peroxide bleaching of softwood and hardwood (eucalypt) kraft pulps was performed in solutions of sodium bicarbonate (NaHCO3), sodium carbonate (Na2CO3), and sodium hydroxide (NaOH). The conventional P stage (hydrogen peroxide + sodium hydroxide; H2O2 + NaOH) was the most effective brightening system without an additional activator. However, peroxide activation by bicarbonate anion (HCO3•) was obvious in all cases where NaHCO3 or Na2CO3 was used. When N,N,N’,N’-tetraacetylethylenediamine (TAED) was added to the bleaching sys-tem, Na2CO3 as the alkali source afforded equal or slightly higher bleached brightness compared to NaOH usage for both the softwood and hardwood pulps. This outcome is attributed to simultaneous peroxide activation by HCO3• and TAED. When applied to the eucalypt pulp, the H2O2/Na2CO3/TAED bleaching system also decreased the bright-ness loss due to thermal reversion.
Journal articles
Magazine articles
Enhancement of processability, surface, and mechanical properties of paper based on rice straw pulp using biopolymers for packaging applications, TAPPI Journal July 2019
ABSTRACT: wo biopolymers, chitosan and oxidized starch, were used as wet-end additives to improve the strength properties of the paper because of their biodegradable and non-hazardous qualities. The present study reports the improvement in surface and strength properties of packaging-grade paper made with rice straw pulp using biopolymers, chitosan, oxidized starch, and surface sizing added at the wet end of the paper machine.Use of chitosan at all doses from 0.5 to 10 kg/ton enhanced important surface and strength properties of paper. The breaking length, tear index, burst index, ring crush strength, stretch, tensile energy absorption index, and Taber stiff-ness of the paper with 10 kg/ton of chitosan as a wet-end additive showed 22%, 14%, 20%, 59%, 16%, 44%, and 48% improvement, respectively, in comparison to control, (i.e, without its addition). The Cobb60 was also reduced by 45%, showing better resistance to water in comparison to rice straw paper alone. The effects of chitosan added at the wet end on the paper surface were investigated using Fourier transform infrared spectroscopy (FTIR). The use of 10 kg/ton of chitosan at the wet end reduced the color and total suspended solids in the back water of the papermak-ing system by 55% and 51%, respectively. Further enhancement in the surface and strength properties of paper was observed following surface sizing with oxidized starch.
Journal articles
Magazine articles
Fundamental molecular characterization and comparison of the O, D0, and E stage effluents from hardwood pulp bleaching, TAPPI Journal 2019
ABSTRACT: The present study characterized effluents from the O, D0, and E stages using nuclear magnetic reso-nance (NMR) and gel permeation chromatography (GPC) techniques to better understand the chemical nature of the dissolved organics formed from the bleaching of a high-yield hardwood kraft pulp. Understanding the structures and molecular weight distribution of these organics is the first step in developing methods to mitigate these contam-inates in the discharged effluents. The results indicated that the molecular weight distribution (MWD) of the dis-solved organics from oxygen delignification effluent is broader than those from D0 and E stage effluents. In addition, the O stage filtrate contained considerable amounts of lignin and xylan fragments, which showed its efficiency in removing such materials. The effluent from the D0 stage contained a lower amount of high molecular weight frag-ments and a higher amount of low molecular weight fragments versus the O-stage filtrate. Aromatic structures were nearly absent in the D0 stage filtrate, but the degraded organic material, presumably from oxidized lignin, contained olefinic (C=C) and carbonyl (C=O) functional groups. Furthermore, higher molecular weight fragments were detected in the E-stage effluent, presumably due to the extensive solubilization and removal of the oxidized lignin generated from the D0 pulp.
Journal articles
Magazine articles
The sticky behavior of pulp and paper mill biosludge during drying, TAPPI Journal June 2019
ABSTRACT: Pulp and paper mill biosludge becomes sticky after being dried to a certain solids content. As bio-sludge becomes sticky, it agglomerates and adheres to the heat transfer surfaces of the dryer. This undesirable property can lower the dryer efficiency and cause the drying equipment to fail.A systematic study was conducted to examine the sticky behavior of biosludge. The stickiness was evaluated by measuring the adhesive force between a sludge cake and a stainless steel substrate, and the cohesive force between a sludge cake and a sludge substrate. The results show that: i) both adhesive and cohesive forces increase markedly as the solids content increases, reaching a maximum value at about 13% solids, and then decrease steadily at a high-er solids content; ii) cohesive force is stronger than adhesive force, implying that biosludge tends to agglomerate rather than adhere to smooth equipment surfaces; and iii) mixing wood fines or fly ash from a biomass boiler reduc-es the stickiness of the mixture. These findings may help mills improve the thermal efficiency of biosludge dryers and to turn biosludge into a more attractive fuel for burning in biomass boilers.
Journal articles
Magazine articles
Fabrication of cross-linked starch-based nanofibrous mat with optimized diameter, TAPPI JOURNAL June 2019
ABSTRACT: The design and synthesis of natural and synthetic polymer blends have received recent and wide attention. These new biomaterials exhibit progress in properties required in the field of medicine and healthcare. Herein, the aim of present study is to fabricate starch (ST)/polyacrylic acid (PAA) electrospun nanofibrous mat with a smooth and uniform morphology, lowest fiber diameter (below 100 nm) and the highest possible starch content. Starch itself is poor in process-ability, and its electrospinning could be quite a challenging process. To address this, we carried out the response surface methodology (RSM) technique for modelling the electrospinning process. In order to have ST/PAA nanofibers with the finest possible diameter, optimized processing parameters (applied volt-age, nozzle-collector distance and feed rate) obtained from RSM technique were applied. ST/PAA electrospun nano-fibers with an average diameter of 74±13 nm were successfully achieved via the electrospinning method for the first time. The structure, preparation and properties of the nanofibrous structure were discussed. Results indicated that drug loaded ST/PAA blend nanofibrous structure has a great potential to be used in controlled drug release systems.
Journal articles
Magazine articles
Large data set analysis to determine refiner plate total cost of ownership, TAPPI Journal June 2019
ABSTRACT: Efficient process data storage and its subsequent analysis are vital to the profitable operation of a paper mill. An evaluation of refiner plate performance was conducted for an integrated paper mill. Trials with two new plate patterns were compared with the incumbent pattern; the goal was to increase refiner plate life. Plate life increased with both new design patterns, and the mill selected one of the two new choices. However, addi-tional impacts to paper machine performance and mill maintenance costs were not considered in the selection deci-sion. A large data set analysis tool was used to identify unrealized savings of 1.5% with reduced fiber usage (basis weight) on the paper machine’s most prevalent grade. The large data analysis indicated that this unrealized benefit with the alternate plate design was not attainable with the chosen plate design.
Journal articles
Magazine articles
Editorial: TAPPI Journal 2018 Best Research Paper delves deeper into press section rewet to address drying efficiency, TAPPI Journal March 2019
ABSTRACT: TAPPI and the TAPPI Journal (TJ) Editorial Board would like to congratulate the authors of the 2018 TAPPI Journal Best Research Paper Award: J. David “Dave” McDonald and Richard J. “Dick” Kerekes. Their paper, “Rewet in wet pressing of pa-per,” appeared on p. 479 of the September 2018 issue. This research was recognized by the Editorial Board for its in-novation, creativity, scientific merit, and clear expression of ideas.
Journal articles
Magazine articles
Editorial: Snapshot from the pandemic: TAPPI Journal Editorial Board shares their experiences, TAPPI Journal April 2020
ABSTRACT: In this most serious time of the global COVID-19 pandemic, I and TAPPI staff have been fortunate to work remotely and practice social distancing. The same goes for our Editorial Board. Still, the business of papermaking has continued, and those on our Board who support the industry through their work and research have had to make adjustments. Here, members of the Editorial Board share their experiences of working during the pandemic. As we all anticipate returning to a new normal that once again allows face-to-face interaction, we hope our TAPPI Journal readers stay safe and healthy as we all personally and professionally navigate this challenging time.
Journal articles
Magazine articles
Papermaking properties of bacterial nanocellulose produced from mother of vinegar, a waste product after classical vinegar production, TAPPI Journal April 2020
ABSTRACT: Bacterial nanocellulose (BNC) has gained a lot of attention in recent years due to its nano-size-derived properties. Although it is essentially chemically similar to plant-derived cellulose, it has smaller size and is enriched in free hydroxyl groups, which greatly improve mechanical properties of reinforced paper. However, although BNC has some unique features, it comes at a high price. In this paper, we introduce a new solution for BNC production. We have isolated bacterial nanocellulose directly from agro-industrial waste—mother of vinegar—and used it in the production of paper sheets. We show here that paper sheets made with the addition of only 10% bacterial nanocellulose from mother of vinegar substantially improved basic mechanical as well as printing properties of paper.
Journal articles
Magazine articles
Creasing severity and reverse-side cracking, TAPPI Journal April 2020
ABSTRACT: Crease cracking can be detrimental to the functionality and appearance of paperboard-based packaging. The effect of creasing severity on the degree of reverse-side crease cracking (bead-side of the crease) of paperboard was investigated. Samples were creased with a range of rule and channel geometries, and the cracking degree was quantified as the percent of cracked length relative to the total length of the crease. The cracking degree was typically below 5% at low crease penetration depths, but was exponentially higher beyond a critical penetration depth. A rule and channel combination with a wider clearance shifted the critical depth to larger values. The creasing severity parameter, termed the creasing draw, converged the cracking degree data from different rule and channel combinations to a single curve. The creasing draw was derived from the same analytical expres-sions as the transverse shear strain and quantifies the length of paper that is drawn into the channel during creasing. The critical draw is defined as the draw at which cracking becomes greater than 5%, which corresponds with the point at which cracking becomes exponential. The critical draw is a material/system parameter that defines the level below which cracking is minimal.