Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Investigation of the factors contributing to malodorous gases emission during secondary fiber reuse, TAPPI Journal June 2026
ABSTRACT: Malodorous gases are commonly produced during secondary fiber reuse, which is harmful to human health and causes environmental pollution. This paper investigated the influence of fiber type and concentration, temperature, and whitewater concentration on the malodorous gases. The results indicated that, in pulp prepared with fresh water, bleached hardwood kraft pulp (LBKP) did not produce malodorous gases after standing for five days. In contrast, the secondary fiber began to release substantial amounts of total volatile organic compounds (TVOC) on the third day and hydrogen sulfide (H2S) and ammonia (NH3) on the sixth day, and black substances began to appear in the pulp, which proved that the microorganisms began to proliferate. With the increase of the secondary fiber concentration, the release amounts of TVOC, H2S, and NH3 gradually rose, along with the black substances in the pulp. With increased temperature, the release of TVOC increased steadily, while the release of H2S and NH3 reached the maximum at about 45°C, and then began to decline. The decrease of the pulp freeness accelerated the generation of the malodorous gases, but the total release amounts of TVOC, H2S, and NH3 were basically the same. With the increase of white water concentration, the release of TVOC, H2S, and NH3 increased rapidly. When the white water/fresh water was 20 mL/80 mL, the slurry changed from pale yellow to aterrimus on the sixth day. Therefore, microorganisms in the secondary fiber caused pulp deterioration, while white water was the main reason for generating a large amount of malodorous gases.
Journal articles
Moisture performance of silica-paper hybrids in the hygroscopic range, TAPPI Journal March 2026
ABSTRACT: Vapor retarders, crucial in building constructions, are traditionally made from plastic-based materials, raising environmental concerns due to the use of fossil materials. This study explores the potential of functionalized papers, particularly silica-paper hybrids, as sustainable alternatives. This work delves into the moisture properties of sol-gel coated linter papers, considering the water vapor permeability and physisorption behavior following DIN EN ISO 12572 and DIN EN ISO 12571. The study addresses hysteresis, noting the lower hysteresis of mesoporous coatings in comparison to dense coatings and implying benefits in moisture release. Findings underscore the need for a nuanced understanding of coating characteristics and their impact on sorption. In order to better assess the relationship between the coating content of the papers and their specific sorption properties, further investigations, such as the measurement of specific surface properties (e.g., specific surface area), are required. The findings of the water vapor diffusion resistance measurement study demonstrate a correlation between the observed resistance and the vapor levels. The results show that the water vapor diffusion resistance is elevated at lower vapor levels when compared to higher levels. This particular material behavior is typically employed within the construction industry for the utilization of moisture-variable water vapor retarders. The silica-paper hybrids exhibit a response that indicates the potential for advancement into a moisture-variable water vapor barrier.
Journal articles
Magazine articles
Modeling and parameter optimization of the papermaking processes by using regression tree model and full factorial design, TAPPI Journal February 2021
ABSTRACT: One of the major challenges in the pulp and paper industry is taking advantage of the large amount of data generated through its processes in order to develop models for optimization purposes, mainly in the papermaking, where the current practice for solving optimization problems is the error-proofing method. First, the multiple linear regression technique is applied to find the variables that affect the output pressure controlling the gap of the paper sheet between the rod sizer and spooner sections, which is the main cause of paper breaks. As a measure to determine the predictive capacity of the adjusted model, the coefficient of determination (R2) and s values for the output pressure were considered, while the variance inflation factor was used to identify and eliminate the collinearity problem. Considering the same amount of data available by using machine learning, the regression tree was the best model based on the root mean square error (RSME) and R2. To find the optimal operating conditions using the regression tree model as source of output pressure measurement, a full factorial design was developed. Using an alpha level of 5%, findings show that linear regression and the regression tree model found only four independent variables as significant; thus, the regression tree model demonstrated a clear advantage over the linear regression model alone by improving operating conditions and demonstrating less variability in output pressure. Furthermore, in the present work, it was demonstrated that the adjusted models with good predictive capacity can be used to design noninvasive experiments and obtain.
Journal articles
Magazine articles
Understanding wet tear strength at varying moisture content in handsheets, TAPPI Journal January 2021
ABSTRACT: A laboratory study was conducted looking at the effects of moisture content on wet tear strength in handsheets. Three different wetting techniques were used to generate the wet tear (Elmendorf-type) data at varying moisture levels, from TAPPI standard conditions (dry) to over 60% moisture content (saturated). Unbleached hardwood and softwood fiber from full-scale kraft pulp production were used. The softwood fiber was refined using a Valley beater to reduce freeness. Handsheets were made with a blend of hardwood and softwood and with refined softwood, without the addition of wet-end chemistry. The resulting grams-force tear data obtained from the test was indexed with basis weight and plotted versus both moisture content and dryness. As moisture content levels in the handsheets increased, the wet tear strength also increased, reaching a critical maximum point. This marked a transition point on the graph where, beyond a critical moisture content level, the tear strength began to decline linearly as moisture increased. This pattern was repeated in handsheets made from a blend of hardwood and softwood and from 100% refined softwood.
Journal articles
Magazine articles
The effect of microfibrillated cellulose on the wet-web strength of paper, TAPPI Journal January 2021
ABSTRACT: The wet-web strength of paper immediately after the press section of a paper machine is a critical factor in determining machine runnability. However, it is difficult to determine at commercial scale, because the web has to be broken and production interrupted in order to obtain a sample for measurement. The use of microfibrillated cellulose (MFC) is believed to increase wet-web strength, as it has allowed filler level increases of 10% or more on many commercial paper machines. In this paper, we describe a laboratory method for estimating the effect of MFC on wet sheet strength after press-ing, as well as actual measurements of wet-web strength from a pilot paper machine trial. These experiments have demonstrated the positive effect of MFC. At solids contents in the range typically observed after pressing, sheets with MFC at fixed filler content are significantly stronger, but also wetter, than those without it. When the use of MFC is combined with a typical increase in filler content, the wet web remains slightly stronger, but also becomes drier than the reference condition. These results are compatible with the theory put forward by van de Ven that wet-web strength is mainly a result of friction between entangled fibers, and they also suggest that the presence of MFC increases this friction.
Journal articles
Magazine articles
A guide to eliminating baggy webs, TAPPI Journal June 2021
ABSTRACT: Slack or baggy webs can cause misregistration, wrinkles, and breaks in printing and converting operations. Bagginess appears as non-uniform tautness in the cross direction (CD) of a paper web. The underlying cause is uneven CD tension profiles, for which there are few remedies once the paper is made. Precision measurements of CD tension profiles combined with trials on commercial paper machines have shown that uniform CD distribution of moisture, basis weight, and caliper profiles at the reel are key to avoiding bagginess. However, the most important but infrequently measured factor is the CD moisture profile entering the dryer section. Wetter areas entering the dryers are permanently elongated more than dry areas, leading to greater slackness in the finished paper. In storage, wound-in tension can amplify baggy streaks in paper near the surface of a roll and adjacent to the core. Unwrapped or poorly wrapped rolls exposed to low humidity environments may have baggy centers caused by moisture loss from the roll edges.All of the factors that impact bagginess have been incorporated in a mathematical model that was used to interpret the observations from commercial trials and can be used as a guide to solve future problems.
Journal articles
Magazine articles
Factors affecting the free shrinkage of handsheets: apparent density, fines content, water retention value, and grammage, TAPPI JOURNAL June 2018
Factors affecting the free shrinkage of handsheets: apparent density, fines content, water retention value, and grammage, TAPPI JOURNAL June 2018
Journal articles
Magazine articles
Polyvinyl alcohol as foaming agent in foam formed paper, TAPPI JOURNAL August 2019
ABSTRACT: The use of polyvinyl alcohol (PVOH or PVA) as a foaming agent in foam formed paper was investigated. Polyvinyl alcohol is a linear, nonionic water-soluble polymer. It has hydrophobic and hydrophilic parts that give it a surface-active character. PVOH is mainly characterized by degree of hydrolysis and molar mass. Degree of hydrolysis is given as mol-% hydroxyl groups on the polymer. Molar mass is measured indirectly by measuring the viscosity of a 4% PVOH solution. The results show that the degree of hydrolysis of PVOH had a strong effect on the foamability of PVOH. Foamability decreased strongly when the degree of hydrolysis increased from 88 to 98 mol-%. The effect of molar mass on foamability was weaker. We saw an increase in foam stability and bubble size with increasing molar mass, but we did not see any effect on maximum air content. PVOH dosage needed to reach >70% air content (F) varied from 2 g/l up to 10.5 g/l, and the lowest addition levels of PVOH needed were achieved with a low molar mass PVOH with a low degree of hydrolysis. The best strength properties were achieved when using fully hydrolyzed PVOH as the foaming agent. Strength properties (both in- and out-of-plane) of samples made using PVOH were better than those made using an anionic foaming agent (sodium dodecyl sulfate, SDS). By adding PVOH binder fibers to the pulp, we were able to further enhance the strength properties of paper and board.
Journal articles
Magazine articles
Creasing severity and reverse-side cracking, TAPPI Journal April 2020
ABSTRACT: Crease cracking can be detrimental to the functionality and appearance of paperboard-based packaging. The effect of creasing severity on the degree of reverse-side crease cracking (bead-side of the crease) of paperboard was investigated. Samples were creased with a range of rule and channel geometries, and the cracking degree was quantified as the percent of cracked length relative to the total length of the crease. The cracking degree was typically below 5% at low crease penetration depths, but was exponentially higher beyond a critical penetration depth. A rule and channel combination with a wider clearance shifted the critical depth to larger values. The creasing severity parameter, termed the creasing draw, converged the cracking degree data from different rule and channel combinations to a single curve. The creasing draw was derived from the same analytical expres-sions as the transverse shear strain and quantifies the length of paper that is drawn into the channel during creasing. The critical draw is defined as the draw at which cracking becomes greater than 5%, which corresponds with the point at which cracking becomes exponential. The critical draw is a material/system parameter that defines the level below which cracking is minimal.
Journal articles
Does kraft hardwood and softwood pulp viscosity correlate to
Does kraft hardwood and softwood pulp viscosity correlate to paper properties?, October 2016 TAPPI JOURNAL