Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Event Type
Collections
Journal articles
Magazine articles
Control of malodorous gases emission from wet-end white water with hydrogen peroxide, TAPPI Journal October 2021
ABSTRACT: White water is highly recycled in the papermaking process so that its quality is easily deteriorated, thus producing lots of malodorous gases that are extremely harmful to human health and the environment. In this paper, the effect of hydrogen peroxide (H2O2) on the control of malodorous gases released from white water was investigated. The results showed that the released amount of total volatile organic compounds (TVOC) decreased gradually with the increase of H2O2 dosage. Specifically, the TVOC emission reached the minimum as the H2O2 dosage was 1.5 mmol/L, and meanwhile, the hydrogen sulfide (H2S) and ammonia (NH3) were almost completely removed. It was also found that pH had little effect on the release of TVOC as H2O2 was added, but it evidently affect-ed the release of H2S and NH3. When the pH value of the white water was changed to 4.0 or 9.0, the emission of TVOC decreased slightly, while both H2S and NH3 were completely removed in both cases. The ferrous ions (Fe2+) and the copper ions (Cu2+) were found to promote the generation of hydroxyl radicals (HOœ) out of H2O2, enhancing its inhibition on the release of malodorous gases from white water. The Fe2+/H2O2 system and Cu2+/H2O2 system exhibited similar efficiency in inhibiting the TVOC releasing, whereas the Cu2+/H2O2 system showed better perfor-mance in removing H2S and NH3.
Journal articles
Magazine articles
Kraft recovery boiler operation with splash plate and/or beer can nozzles — a case study, TAPPI Journal Octobr 2021
ABSTRACT: In this work, we study a boiler experiencing upper furnace plugging and availability issues. To improve the situation and increase boiler availability, the liquor spray system was tuned/modified by testing different combinations of splash plate and beer can nozzles. While beer cans are typically used in smaller furnaces, in this work, we considered a furnace with a large floor area for the study. The tested cases included: 1) all splash plate nozzles (original operation), 2) all beer can nozzles, and 3) splash plate nozzles on front and back wall and beer cans nozzles on side walls. We found that operating according to Case 3 resulted in improved overall boiler operation as compared to the original condition of using splash plates only. Additionally, we carried out computational fluid dynamics (CFD) modeling of the three liquor spray cases to better understand the furnace behavior in detail for the tested cases. Model predictions show details of furnace combus-tion characteristics such as temperature, turbulence, gas flow pattern, carryover, and char bed behavior. Simulation using only the beer can nozzles resulted in a clear reduction of carryover. However, at the same time, the predicted lower furnace temperatures close to the char bed were in some locations very low, indicating unstable bed burning. Compared to the first two cases, the model predictions using a mixed setup of splash plate and beer can nozzles showed lower carryover, but without the excessive lowering of gas temperatures close to the char bed.
Journal articles
Magazine articles
Corrosion damage and in-service inspection of retractable sootblower lances in recovery boilers, TAPPI Journal October 2021
ABSTRACT: Several reports of accidents involving serious mechanical failures of sootblower lances in chemical recovery boilers are known in the pulp and paper industry. These accidents mainly consisted of detachment and ejection of the lance tip, or even of the entire lance, to the inside of the furnace, towards the opposite wall. At least one of these cases known to the author resulted in a smelt-water explosion in the boiler.In other events, appreciable damage or near-miss conditions have already been experienced. The risk of catastrophic consequences of the eventual detachment of the lance tip or the complete lance of a recovery boiler soot-blower has caught the attention of manufacturers, who have adjusted their quality procedures, but this risk also needs to be carefully considered by the technical staff at pulp mills and in industry committees.This paper briefly describes the failure mechanisms that prevailed in past accidents, while recommending inspection and quality control policies to be applied in order to prevent further occurrences of these dangerous and costly component failures. Digital radiography, in conjunction with other well known inspection techniques, appears to be an effective means to ensure the integrity of sootblower lances in chemical recovery boilers used in the pulp and paper industry.
Particulate Emissions from Char Bed Burning, 2004 International Chemical Recovery Conference
Particulate Emissions from Char Bed Burning, 2004 International Chemical Recovery Conference
Small Particle Migration Mechanisms in Consolidating Pigment Coating Layers, 2008 Advanced Coating Fundamentals Symposium
Small Particle Migration Mechanisms in Consolidating Pigment Coating Layers, 2008 Advanced Coating Fundamentals Symposium
A Roadmap for Reliability Excellence, 2008 Engineering, Pulping and Environmental Conference
A Roadmap for Reliability Excellence, 2008 Engineering, Pulping and Environmental Conference
BALANCING CHLORINE DIOXIDE AND PEROXIDE IN NORTH AMERICAN ECF BLEACHING SEQUENCES FOR SOFTWOOD KRAFT PULPS, 2008 Engineering, Pulping and Environmental Conference
BALANCING CHLORINE DIOXIDE AND PEROXIDE IN NORTH AMERICAN ECF BLEACHING SEQUENCES FOR SOFTWOOD KRAFT PULPS, 2008 Engineering, Pulping and Environmental Conference
Beyond RCM, 2008 Engineering, Pulping and Environmental Conference
Beyond RCM, 2008 Engineering, Pulping and Environmental Conference
Characterization of Lignin Gasification and Pyrolysis, 2008 Engineering, Pulping and Environmental Conference
Characterization of Lignin Gasification and Pyrolysis, 2008 Engineering, Pulping and Environmental Conference
CHLORATE REDUCTION IN EUCALYPTUS PULP BLEACHING, 2008 Engineering, Pulping and Environmental Conference
CHLORATE REDUCTION IN EUCALYPTUS PULP BLEACHING, 2008 Engineering, Pulping and Environmental Conference