Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Web instability in the open draw and the impact on paper machine efficiency, TAPPI Journal May 2022
ABSTRACT: Paper is most likely to break in the first open draw on a paper machine where it is unsupported, wettest, and weakest. Tension is applied to peel the web from the roll surface, as well as minimize web flutter in the open draw. The average tension is well below the breaking point and is often set by adjusting the speed difference between the press and the next machine element by visually observing the behavior of the web. However, machine direction variations caused by instabilities in the paper machine can cause tension swings that exceed the strength of the web. Measurement of the web’s release point from press rolls on pilot and commercial paper machines was used to identify the cause of tension instabilities. Variations in the speed of the paper machine drives and the work of adhesion from the press roll surface were identified as key factors. Fluctuations of paper moisture, which affects the elastic modulus and strength of the web, appear to be less important.
Journal articles
Using multi-method analysis to identify challenging paper machine deposits and defects, TAPPI Journal March 2025
ABSTRACT: Based on its speed and versatility, Fourier transform infrared (FTIR) spectroscopy is the industry’s common starting point for analysis of a paper machine deposit or defect sample. However, certain contaminants and papermaking process additives cannot be precisely identified solely by infrared spectral interpretation. This lack of specificity could lead to a misinterpretation of the composition of the deposit or defect. A multi-method analysis uses data from two or more analytical techniques, including FTIR spectroscopy, microbiological staining/phase contrast microscopy, pyrolysis-gas chromatography/mass spectrometry (Pyro-GC/MS), and scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDX), to produce a more specific assessment of a sample’s composition. This paper discusses the use of a multi-method analysis in deposit and defect analysis and presents several case studies that demonstrate how this comprehensive approach can often produce an interpretation result of greater conviction and value to the papermaker.
Journal articles
Magazine articles
Fate of phosphorus in the recovery cycle of the kraft pulping process, TAPPI Journal March 2020
ABSTRACT: The accumulation of nonprocess elements in the recovery cycle is a common problem for kraft pulp mills trying to reduce their water closure or to utilize biofuels in their lime kiln. Nonprocess elements such as magnesium (Mg), manganese (Mn), silicon (Si), aluminum (Al), and phosphorus (P) enter the recovery cycle via wood, make-up chemicals, lime rock, biofuels, and process water. The main purge point for these elements is green liquor dregs and lime mud. If not purged, these elements can cause operational problems for the mill. Phosphorus reacts with calcium oxide (CaO) in the lime during slaking; as a result, part of the lime is unavailable for slaking reactions. The first part of this project, through laboratory work, identified rhenanite (NaCa(PO4)) as the form of P in the lime cycle and showed the negative effect of P on the availability of the lime. The second part of this project involved field studies and performing a mass balance for P at a Canadian kraft pulp mill.
Journal articles
Magazine articles
The use of hollow sphere pigments as strength additives in paper and paperboard coatings—Part 2: Optimization in paperboard formulations for opacity and strength, TAPPI Journal November 2020
ABSTRACT: This report aims to summarize the efforts in testing the properties of coatings for paperboard utilizing hollow sphere pigments (HSPs). HSPs are known to effectively scatter light and replace titanium dioxide (TiO2) in architectural coating formulations. The effect of the particle size and void fraction was evaluated, along with many coating parameters, including level of addition, binder chemistry, and blends of two HSPs. The small HSPs that have optimized voids for scattering light showed equivalent strength to the TiO2-containing control. The strength data was surprising, particularly the improvement in strength for coatings containing large particle size HSPs. Because of this increase in strength, four parts of binder could be removed, which allowed for higher brightness while not compromising other properties, including hot melt glueability. These trends held true using different binder chemistries (styrene acrylic, vinyl acrylic, and styrene butadiene). Upon refining the formulations further, blends of two HSPs showed further benefit.
Journal articles
Magazine articles
Influence of pallet pattern on top-to-bottom compression performance of unitized loads, TAPPI Journal November 2021
ABSTRACT: Environmental scaling factors estimate a corrugated container’s ability to withstand various conditions it will encounter during the storage and distribution process. In this project, we examined the compressive resistance of unitized loads using differing pallet stacking patterns. To simulate real-world failure scenarios in our laboratory tests, we used two different nominal board grades of single-wall C-flute regular slotted containers loaded with a plywood panel and bagged salt to direct the failure location to the bottom of the stack. Our results showed that the columnar aligned pattern provided the greatest compressive resistance and the interlocked stacking arrangement yielded the lowest of the patterns evaluated. Based on the study results, we calculated box compression retention multipliers for each pattern and compared them to scaling factors published by the Fibre Box Association.
Journal articles
Acoustic analysis of recovery boiler dissolving tank operati
Acoustic analysis of recovery boiler dissolving tank operation and smelt shattering efficiency, TAPPI JOURNAL September 2016
Journal articles
Magazine articles
Characterization and evaluation of antioxidation of lignin from bamboo powder using a formic acid-catalyzed ethanol organosolv process, TAPPI JOURNAL January 2019
Characterization and evaluation of antioxidation of lignin from bamboo powder using a formic acid-catalyzed ethanol organosolv process, TAPPI JOURNAL January 2019
Journal articles
Magazine articles
Editorial: TAPPI Journal 2018 Best Research Paper delves deeper into press section rewet to address drying efficiency, TAPPI Journal March 2019
ABSTRACT: TAPPI and the TAPPI Journal (TJ) Editorial Board would like to congratulate the authors of the 2018 TAPPI Journal Best Research Paper Award: J. David “Dave” McDonald and Richard J. “Dick” Kerekes. Their paper, “Rewet in wet pressing of pa-per,” appeared on p. 479 of the September 2018 issue. This research was recognized by the Editorial Board for its in-novation, creativity, scientific merit, and clear expression of ideas.
Journal articles
Magazine articles
An effective method for determining the retention and distribution of cellulose nanofibrils in paper handsheets by dye labeling, TAPPI JOURNAL March 2018
An effective method for determining the retention and distribution of cellulose nanofibrils in paper handsheets by dye labeling, TAPPI JOURNAL March 2018
Journal articles
Magazine articles
Factors affecting particulate removal efficiency of kraft recovery boiler electrostatic precipitators: a technical review, TAPPI JOURNAL May 2018
Factors affecting particulate removal efficiency of kraft recovery boiler electrostatic precipitators: a technical review, TAPPI JOURNAL May 2018