Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
A novel unit operation to remove hydrophobic contaminants, TAPPI Journal April 2020
ABSTRACT: For mills making paper with recovered fiber, removal of hydrophobic contaminants is essential for trouble-free operation of paper machines. Significant cost savings on paper machine operation can be achieved by reducing deposits, which results in better quality, reduced downtime, increased fiber yield, and reduced energy consumption. Bubble nucleation separation (BNS) is a relatively new process for removing hydrophobic particles. When vacuum is applied to a slurry, dissolved gas bubbles nucleate on hydrophobic particles and drag them to the surface for easy removal. We constructed a 16-L batch unit to evaluate the effect of operating parameters on removal of hydrophobic particles, using statistical design of experiments. These results were used to guide our design of a 16-L continuous unit. We tested this unit on laboratory and mill samples. The removal of 60%•80% of hydrophobic particles was achieved with a low reject rate of < 2%.Following on this success, we built a 200-L pilot unit and tested it in our pilot plant. With promising results there, we installed the pilot unit at a commercial paper recycling mill. Over the course of several mill trials, we showed that it was possible to remove a considerable amount of suspended solids from paper machine white water with less than 2% rejects. Unfortunately, due to the unit only treating 50 L/min and the mill flow being 12000 L/min, we were not able treat a sufficient portion of the white water to know whether a large-scale implementation of BNS would improve paper machine runnability.
Journal articles
Magazine articles
Mill experience of calcium carbonate scale formation in green liquor pipelines, TAPPI Journal August 2020
ABSTRACT: Experience of hard calcite (CaCO3) scale formation in green liquor pipelines at four kraft pulp mills was systematically investigated to determine if there is any correlation between the severity of the scaling problem at each mill and the design and operating conditions of its causticizing plant. The results show that the high degree of supersaturation of calcium ions (Ca2+) in the liquor is the main contributing factor. Mills that operate at a lower green liquor total titratable alkali (TTA), higher causticity, and a larger liquor temperature drop are more likely to produce a green liquor that is supersaturated with Ca2+, and thus experience more severe scaling problems. In order to minimize CaCO3 scaling, the green liquor handling equipment should be operated as steady as possible to avoid conditions that allow Ca2+ to be supersaturated. The strategies include minimizing variations in liquor TTA, insulating the green liquor pipelines to reduce temperature gradients, and adding lime mud to weak wash to provide seeds for precipitation to occur on mud particles instead of on metal substrate.
Journal articles
Magazine articles
Standards
On-machine visible dirt measurement on moving sheets and the relationships to standard laboratory methods, TAPPI Journal August 2020
ABSTRACT: There has been a proliferation of new sensors to measure on-machine dirt specks that employ different technologies and methodologies to perform measurements. The differences in the on-machine technologies are discussed in terms of the TAPPI and ISO standard laboratory test methods with respect to dirt detection using light reflected from, or light transmitted through, the sheet. Also discussed are the requirements for measuring sta-tistically representative areas of the sheet; the difference between the dirt physical size and Equivalent Black Area (EBA) size; and the implication of these issues when specifying cleanliness acceptance criteria.This technical brief describes on-machine visible dirt measurement’s relationship to standard laboratory testing.
Journal articles
Magazine articles
Standards
Relating bending stiffness measurements across various free span lengths, TAPPI Journal August 2020
ABSTRACT: Bending stiffness should be an intrinsic property of a material, so it is puzzling that the TAPPI Standard Test Method T 836 “Bending stiffness, four point method” specifies span lengths when testing different types of corrugated fiberboard. These specified spans often limit the samples that can be measured with this method. To better understand the relationship between bending stiffness and span length, we performed measurements on a range of materials at different spans. The results provide a practical tool enabling comparison of bending stiffness measurements made at various span lengths. Additionally, this note discusses several areas that could serve as the foundation for more fundamental work exploring the bending behavior of corrugated board.
Journal articles
Editorial: Honghi Tran: A Prolific TAPPI Journal, TAPPI JOUR
Editorial: Honghi Tran: A Prolific TAPPI Journal, TAPPI JOURNAL July 2016
Journal articles
Estimation of the S/G Ratios of the Lignins in Three Widely
Estimation of the S/G Ratios of the Lignins in Three Widely used North American Hardwoods, TAPPI JOURNAL July 2016
Journal articles
Corrosion Mnitoring and Root Cause Identification in High So
Corrosion Mnitoring and Root Cause Identification in High Solids Concentrators, TAPPI JOURNAL July 2016
Journal articles
Evaluation of Near-Drum Thinning Data in Recovery Boiler Gen
Evaluation of Near-Drum Thinning Data in Recovery Boiler Generating Bank Tubes, TAPPI JOURNAL July 2016
Journal articles
A comparative study of enzymatic and Fenton pretreatment app
A comparative study of enzymatic and Fenton pretreatment applied to a birch kraft pulp used for MFC production in a pilot scale high-pressure homogenizer, TAPPI JOURNAL June 2016
Journal articles
Effects of cellulosic nanofibrils on papermaking properties
Effects of cellulosic nanofibrils on papermaking properties of fine papers, TAPPI JOURNAL June 2016