Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Corrosion Mnitoring and Root Cause Identification in High So
Corrosion Mnitoring and Root Cause Identification in High Solids Concentrators, TAPPI JOURNAL July 2016
Journal articles
Evaluation of Near-Drum Thinning Data in Recovery Boiler Gen
Evaluation of Near-Drum Thinning Data in Recovery Boiler Generating Bank Tubes, TAPPI JOURNAL July 2016
Journal articles
Magazine articles
Operational limits of blade coating associated with high aspect ratio pigments: Part I—bench top blade coater, TAPPI Journal February 2019
Operational limits of blade coating associated with high aspect ratio pigments: Part I—bench top blade coater, TAPPI Journal February 2019
Journal articles
Magazine articles
Operational limits of blade coating assocciated with high aspect ratio pigments: PartII—cylindrical laboratory coater, TAPPI Journal February 2019
Operational limits of blade coating assocciated with high aspect ratio pigments: PartII—cylindrical laboratory coater, TAPPI Journal February 2019
Journal articles
Magazine articles
Cracking at the fold in double layer coated paper: the influence of latex and starch composition, TAPPI Journal February 2019
Cracking at the fold in double layer coated paper: the influence of latex and starch composition, TAPPI Journal February 2019
Journal articles
Magazine articles
Synthesis and characterization of novel foams by pyrolysis of lignin, TAPPI Journal January 2019
Synthesis and characterization of novel foams by pyrolysis of lignin, TAPPI Journal January 2019
Journal articles
Magazine articles
Rheological characterization of tack and viscoelasticity of compositions of crepe coating used in the Yankee dryer, TAPPI Journal November 2019
ABSTRACT: The vast majority of tissue production uses creping to achieve the required set of properties on the base sheet. The Yankee coating helps to develop the desired crepe that in turn determines properties such as bulk and softness. The adhesion of the sheet to the Yankee surface is a very important characteristic to consider in achieving the desired crepe. The coating mix usually consists of the adhesive, modifier, and release. A good combination of these components is essential to achieving the desired properties of the tissue or towel, which often are determined by trials on the machine that can be time consuming and lead to costly rejects. In this paper, five compo-sitions of an industrial Yankee coating adhesive, modifier, and release were examined rheologically. The weight ratio of the adhesive was kept constant at 30% in all five compositions and the modifier and release ratios were varied. The normal force and work done by the different compositions have been shown at various temperatures simulating that of the Yankee surface, and the oscillatory test was carried out to explain the linear and nonlinear viscoelastic characteristic of the optimal coating composition.
Journal articles
Magazine articles
A novel predictive method for filler coflocculation with cellulose microfibrils, TAPPI Journal November 2019
ABSTRACT: Different strategies aimed at reducing the negative impact of fillers on paper strength have been the objective of many studies during the past few decades. Some new strategies have even been patented or commercialized, yet a complete study on the behavior of the filler flocs and their effect on retention, drainage, and formation has not been found in literature. This type of research on fillers is often limited by difficulties in simulating high levels of shear at laboratory scale similar to those at mill scale. To address this challenge, a combination of techniques was used to compare preflocculation (i.e., filler is flocculated before addition to the pulp) with coflocculation strategies (i.e., filler is mixed with a binder and flocculated before addition to the pulp). The effect on filler and fiber flocs size was studied in a pilot flow loop using focal beam reflectance measurement (FBRM) and image analysis. Flocs obtained with cationic polyacrylamide (CPAM) and benonite were shown to have similar shear resistance with both strategies, whereas cationic starch (CS) was clearly more advantageous when coflocculation strategy was used. The effect of flocculation strategy on drainage rate, STFI formation, ash retention, and standard strength properties was measured. Coflocculation of filler with CPAM plus bentonite or CS showed promising results and produced sheets with high strength but had a negative impact on wire dewatering, opening a door for further optimization.
Journal articles
Magazine articles
Lignin-based resins for kraft paper applications, TAPPI Journal November 2019
ABSTRACT: We investigated miscanthus (MS) and willow (W) lignin-furfural based resins as potential reinforce-ment agents on softwood and hardwood kraft paper. These resins might be sustainable alternatives to the commercial phenolformaldehyde (PF) resins. Phenol is a petrochemical product and formaldehyde has been classified as a carcinogen by the U.S. Environmental Protection Agency. The lignin used in this study was derived from hot water extraction (160ºC, 2 h) of MS and W biomass, and may be considered sulfur-free. These biorefinery lignins were characterized for their chemical composition and inherent properties via wet chemistry and instrumental techniques. The resin blends (MS-resin and W-resin) were characterized for their molecular weight, thermal behavior, and mechanical properties. Mechanical properties were measured by the resin’s ability to reinforce softwood and hard-wood kraft papers. The effect of adding hexamethylenetetramine (HMTA), a curing agent, to the resin was also examined. Mixtures of PF and lignin-based resins were investigated to further explore ways to reduce use of non-renewables, phenol, and carcinogenic formaldehyde. The results show that lignin-based resins have the potential to replace PF resins in kraft paper applications. For softwood paper, the highest strength was achieved using W-resin, without HMTA (2.5 times greater than PF with HMTA). For hardwood paper, MS-resin with HMTA gave the highest strength (2.3 times higher than PF with HMTA). The lignin-based resins, without HMTA, also yielded mechanical properties comparable to PF with HMTA.
Journal articles
Nonlinear modeling of batch digester discharge dynamics with rheology-driven hydraulic transport and drainability coupling, TAPPI Journal September 2026
ABSTRACT: Batch digester blowdown constitutes a strongly nonlinear transient transport process governed by the coupled evolution of pulp consistency, slurry density, hydraulic resistance, liquid inventory, and discharge line dynamics. A control-oriented nonlinear formulation is developed by coupling dry fiber and free liquor mass balances with phase volume reconstruction, consistency-dependent hydraulic resistance, channeling and drainability effects, and a power law head flow relationship derived within a lumped hydraulic inertance framework. A fixed-gain PI controller obtained from local linearization is employed as the conventional benchmark, whereas an integral sliding mode controller (SMC) explicitly compensates the nonlinear time-varying hydraulic structure and bounded disturbances. Both strategies are evaluated under identical actuator constraints and sequential perturbations involving opposing head, hydraulic resistance, channeling, drainability, and dilution. Numerical results demonstrate lower rootmean- square error, integral absolute error, and peak flow-tracking error for the SMC, with rapid recovery toward the prescribed sliding boundary layer and improved robustness to variations in the nonlinear flow exponent n. Cumulative electrical energy and batch-specific specific energy consumption remain comparatively similar, indicating that the principal SMC benefit is enhanced hydraulic regulation rather than substantial batch energy reduction. Specific energy consumption is an established metric for energetic assessment of slurry transport. Model-based hydraulic demand, electrical power, and sliding manifold surfaces further characterize the nonlinear operating domain. The resulting framework provides a computational proof-of-concept for modeling and control of transient batch digester discharge systems.