Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Effect of pressure and time on water absorption of coated paperboard based on a modified Cobb test method, TAPPI Journal April 2024
ABSTRACT: This manuscript presents the study of water absorption by paperboard subjected to water at high hydrostatic pressure based on a modified Cobb tester. The new tester is based on TAPPI Standard Test Method T 441; however, the water column can reach up to 550 mm. The evaluation consisted of measurements of water absorption for coated and uncoated paperboard at different exposure times from 5 s to 45 s and water column heights from 10 mm to 500 mm (corresponding to hydrostatic pressures 98 Pa and 4.9 kPa, respectively). The coatings were formulated as a combination of styrene acrylate (SA; two binder levels) and two types of ground calcium carbonates (differing particle sizes) to form the two pre-coating structures: open and closed. The coating weight was 6 g/m2 applied on 210 g/m2 solid bleached board (SBB). In addition, 210 g/m2 uncoated boards were studied. Characterization of the coatings was performed with scanning electron microscopy (SEM), mercury intrusion, and roughness. It was found that the new device properly mimics the conditions of the current Cobb tester. The characterization of the coating also confirmed the presence of more open/larger pores of open coatings, confirming the desired coating structure. The absorption of boards was mainly driven by exposure pressure by comparing with exposure time. This was already evident after shorter periods of exposure time at 5 s and also 15 s exposure time. Paperboards with open coatings showed slightly higher absorption than other boards.
Journal articles
Magazine articles
Compression refining: the future of refining? Application to Nordic bleached softwood kraft pulp, TAPPI Journal August 2024
ABSTRACT: A new compression refining technology based on the kneading of high consistency pulp has been selected and tested in various conditions with a model Nordic bleached softwood kraft (NBSK) pulp. The method uses a kneader mixer referred to as the ultra continuous mixer (UCM) to condition the pulp. Its performance levels were also compared with those obtained with traditional low consistency (LC) refining of the same pulp.Compression refining of the NBSK pulp with the UCM led to a much better °SR/strength compromise than conventional LC refining. High strength properties can also be achieved by compression refining, in a range similar to/or better than LC refining. The higher the strength required, the greater the advantages of this technology: for a given strength, a difference of up to 10°SR can be obtained as compared to LC refined pulp. Moreover, a higher tear index can be obtained with compression refining, since fiber cutting is greatly reduced.The lower °SR is due to the release of fewer cellulosic fines, which also results in the manufacturing of new papers combining a high strength and a high permeability that cannot be obtained with traditional LC refining. Indeed, with LC refining, a high strength is generally associated with a low permeability. Upscaling this technology seems to be possible since large production devices are already on the market for applications other than paper/pulp. With this new pulp behavior, papermakers will have to learn to think differently, as paper strength and °SR can now be decorrelated.
Journal articles
Magazine articles
Dynamic out-of-plane compression of paperboard — Influence of impact velocity on the surface, TAPPI Journal February 2024
ABSTRACT: Processes that convert paperboard into finished products include, for example, printing, where the paperboard is subjected to rapid Z-directional (ZD) compression in the print nip. However, measuring and evaluating the relevant properties in the thickness direction of paperboard are not necessarily straightforward or easy. Measuring at relevant, millisecond deformation rates further complicates the problem. The aim of the present work is to elucidate some of the influences on the compressive stiffness. Both the initial material response and the overall compressibility of the paperboard is studied. In this project, the effect on the material response from the surface structure and the millisecond timescale recovery is explored.The method utilized is a machine called the Rapid ZD-tester. The device drops a probe in freefall on the substrate and records the probe position, thus acquiring the deformation of the substrate. The probe is also allowed to bounce several times on the surface for consecutive impacts before being lifted for the next drop. To investigate the time dependent stiffness behavior, the probe is dropped several times at the same XY position on the paperboard from different heights, thus achieving different impact velocities. The material response from drops and bounces combined allows study of the short-term recovery of the material. The material in the study is commercial paperboard. The paperboard samples are compared to material where the surface has been smoothed by grinding it. Our study shows that there is a non-permanent reduction in thickness and a stiffening per bounce of the probe, indicating a compaction that has not recovered in the millisecond timescale. Additionally, a higher impact velocity has an initial stiffening effect on the paperboard, and this is reduced by smoothing the surface.
Journal articles
Magazine articles
Amphoteric dry strength chemistry approach to deal with low-quality fiber and difficult wet-end chemistry conditions in the Asian and North American markets, TAPPI Journal January 2024
ABSTRACT: With Japan’s high recycling rates and low access to fresh fiber sources, reaching strength targets in manufacturing packaging materials is a challenge. Declining quality of recycled fiber and minimal freshwater con-sumption results in difficult wet-end chemistry conditions in terms of high conductivity and elevated levels of dissolved and colloidal substances (DCS). These trends are somewhat typical of other Asian regions. Due to global trade, Asian packaging materials have become a part of the North American (NA) raw material pool. The gradual closing of mill water circuits for fresh water and energy savings results in more difficult wet-end chemistry conditions experienced in North America. China’s ban on the import of mixed paper and the consequent ban on all waste-paper imports triggered a significant price drop in recycled raw material, resulting in plans for increased manufacturing capacity in North America. Between increased demand, decreasing fiber quality, and movement towards more closed white water systems associated with packaging grade paperboard (even a virgin fiber mill uses a fair amount of recycled fiber), new methods to overcome strength reduction in raw materials must be proactively considered for North America. Reviewing the strategies currently used in the Asian industry regarding strength development is an excellent starting place for NA producers. A clear difference between Asian and NA wet-end chemistry is the dominant position of amphoteric dry strength agents. This paper reviews the fundamentals of dry strength development that explain the trend towards the increased application of amphoteric dry strength technology for poor-quality fiber and highly contaminated water circuits in Asian markets. This paper discusses the development and application perfor-mance of the novel 4th generation amphoteric polyacrylamide (AmPAM) dry strength technology, based on selected laboratory and mill case studies.
Journal articles
Magazine articles
Modeling the dynamics of evaporator wash cycles, TAPPI Journal July 2024
ABSTRACT: Kraft pulping is a process that utilizes white liquor, composed of sodium sulfide (Na2S) and sodium hydroxide (NaOH), for wood delignification and pulp production. This process involves washing the dissolved organics and spent chemicals from the pulp, resulting in the generation of black liquor. Prior to its use as fuel in the recovery boiler, the black liquor is concentrated in multiple-effect evaporators. During the evaporation process, the inorganic salts present in the liquor become supersaturated and undergo crystallization. Fluctuations in sodium, carbonate, sulfate, and oxalate can give rise to severe sodium salt scaling events, which significantly impact the thermal efficiency of the evaporators, and ultimately, pulp production. Dynamic modeling provides insights into fluctuations in liquor chemistry in the evaporators. The primary objective of this study was to employ dynamic modeling to evaluate the effects of wash liquor recovery from evaporator wash cycles. The dynamics associated with wash cycles encompass variations in the concentrations of salts and solids in the recovered wash liquor, changes in the flow rate of wash liquor recovery, and fluctuations in liquor volume within the liquor tanks. The dynamic model was developed using Matlab Simulink and applied to the evaporation plant of a pulp mill in South America. By utilizing one month of mill process data, the model enabled the evaluation of fluctuations in liquor chemistry due to evaporator wash cycles. The developed model has demonstrated the potential to estimate the concentration of key ions responsible for scaling and to contribute to enhancements in evaporator washing strategies.
Journal articles
Water and grease resistance of paperboard coated with long chain cellulose fatty acid esters using electrostatic powder coating, TAPPI Journal April 2026
ABSTRACT: Fiber-based materials used for foodservice, takeaway, and other packaging applications must typically provide water and grease resistance. Simultaneously, there is growing interest towards bio-based and renewable barrier coatings. In this study we applied thermoplastic long chain fatty acid cellulose esters onto paperboard using electrostatic powder coating to create barrier properties of interest. Electrostatic powder coating provides a water-free process to tackle moisture-induced quality issues and to provide an even coating layer. Cellulose octanoate and palmitate esters were produced in pilot scale. These were ground into fine particles using liquid nitrogen and applied onto paperboard sheets using an electrostatic powder gun. The loosely packed coatings were fixed and fused onto the paperboard by hot pressing. We characterized the coated sheets for coating thickness, contact angles with water, water absorption, grease resistance (KIT), and olive oil barrier. Two commercial polyethylene powders were used as references. Our results indicated that the long chain cellulose fatty acid ester coatings were thermoplastic and hydrophobic with contact angles above 100°. Water absorption was similar to the reference coatings. While grease resistance was lower than with the references, the cellulose ester coatings slowed down diffusion of olive oil through the paperboard. Cellulose octanoate ester with a lower melt viscosity already provided smooth coatings after the initial hot pressing step, while in most cases, the second post hot pressing step further improved the barrier properties.
Journal articles
Comparative evaluation of conical and double disk refiners: Effects of operating mode, refining intensity, and device geometry on energy consumption and paper properties, TAPPI Journal August 2026
ABSTRACT: This study investigates the effects of refiner operating mode and refining intensity adjusted via pulp flow rate, applied power, and refiner speed on the refining characteristics of high-yield southern softwood. We compared Valmet’s OptiFiner PRO (conical) and DD6700 (double disk) refiners under matched specific edge load (SEL) conditions. Batch and one-pass modes were evaluated for their impact on energy efficiency and physical paper properties. The results showed that while SEL provides a useful baseline, it does not fully account for differences in refiner geometry, particularly angular parameters. With the chosen plate sets, C-factor analysis revealed that the OptiFiner PRO delivers a lower number of fiber impacts at a higher intensity per impact compared to DD6700 at similar SEL, influencing fiber length, short-span compression test (STFI) index, and tear strength development. These findings offer actionable insights for mills seeking to optimize refining efficiency and cost. In summary, conical refiners may provide advantages in compression strength at mid-range energies, while double disk refiners maintain higher tear strength at elevated energies due to better fiber length preservation.
Journal articles
Simplified modeling of a complete rotary lime kiln at a pulp mill, TAPPI Journal February 2026
ABSTRACT: Rotary lime kilns are essential and complex components in pulp mills using the kraft process. They are primarily used to produce lime (CaO), which is then employed to make white liquor, the reagent used to separate wood fibers. To understand and improve the performance of the kiln, modeling its behavior is essential. However, the kiln operates through a complex combination of thermal and chemical phenomena. That is why a simplified approach was used to tackle this challenge. A zero/one-dimensional steady-state analysis was performed based on first principles to simplify the modeling process and reduce the need for experimental data. Additional assumptions, such as steady-state operation and the absence of a refractory lining, were introduced to further simplify the model so that it can be used for daily analysis. Moreover, the auxiliary equipment of the plant, such as the intercooler and preheat cyclone, is also modeled. The final model was validated using data from the literature and a two-month analysis of experimental measure-ments from the Burgo Ardennes lime kiln in Virton, Belgium. It shows good agreement with the available data, with a 6% deviation for the adiabatic flame temperature and a 17% average error in predicting the kiln shell outside temperature. For the fuel and lime flow rate predictions, also validated over the same two-month period, the errors were -6.6% and 0.6%, respectively.
Journal articles
Point load measurements on paperboard packages and bulging, TAPPI Journal March 2026
ABSTRACT: Paperboard packaging is made by processing board materials into sheets or rolls and shaping them through creasing, cutting, folding, and erecting. The conversion process generates residual moments at the folds that cause panel bulging. This study experimentally investigates how the bulging introduced during the converting processes influence the mechanical response of paperboard packages during point load testing within the elastic deformation range. The study shows that panel bulging may significantly affect packaging performance as-perceived strength and stiffness. Bulging, influenced by the board’s basis weight, can affect the package performance even more than packaging stiffness. Point load tests in the elastic region were performed on empty packages (78 mm × 50 mm × 110 mm) with force applied at specific points along their long sides. The packages evaluated in this study were made of two identically processed materials of different grammages. The heavier material showed more pronounced bulging than the lighter one, leading to overlapping force-displacement curves for the packages, and to that, a lower force and stiffness may be measured at a certain indentation depth for the package of heavier material. This complicates material choice according to functional requirements. The results show that a highly bulged package might resemble one with less bulging of another material. According to the results, it is not certain that a higher grammage package shows a higher indentation force and stiffness than a lower grammage package when measured at a certain indentation. This indicates that optimizing the creasing and folding processes can be a way to enhance performance rather than simply increasing board weight. The study underscores the importance of controlling converting parameters, especially creasing and folding behavior. Well-performed creasing and folding gives a low residual momentum, little bulging, and a high stiffness and compression strength at point loading in the elastic region. Proper optimization can improve packaging performance and manual handling user-friendliness.
Journal articles
Nonlinear modeling of batch digester discharge dynamics with rheology-driven hydraulic transport and drainability coupling, TAPPI Journal September 2026
ABSTRACT: Batch digester blowdown constitutes a strongly nonlinear transient transport process governed by the coupled evolution of pulp consistency, slurry density, hydraulic resistance, liquid inventory, and discharge line dynamics. A control-oriented nonlinear formulation is developed by coupling dry fiber and free liquor mass balances with phase volume reconstruction, consistency-dependent hydraulic resistance, channeling and drainability effects, and a power law head flow relationship derived within a lumped hydraulic inertance framework. A fixed-gain PI controller obtained from local linearization is employed as the conventional benchmark, whereas an integral sliding mode controller (SMC) explicitly compensates the nonlinear time-varying hydraulic structure and bounded disturbances. Both strategies are evaluated under identical actuator constraints and sequential perturbations involving opposing head, hydraulic resistance, channeling, drainability, and dilution. Numerical results demonstrate lower rootmean- square error, integral absolute error, and peak flow-tracking error for the SMC, with rapid recovery toward the prescribed sliding boundary layer and improved robustness to variations in the nonlinear flow exponent n. Cumulative electrical energy and batch-specific specific energy consumption remain comparatively similar, indicating that the principal SMC benefit is enhanced hydraulic regulation rather than substantial batch energy reduction. Specific energy consumption is an established metric for energetic assessment of slurry transport. Model-based hydraulic demand, electrical power, and sliding manifold surfaces further characterize the nonlinear operating domain. The resulting framework provides a computational proof-of-concept for modeling and control of transient batch digester discharge systems.