Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Effects of D0-stage temperature, pH, and kappa factor on chl
Effects of D0-stage temperature, pH, and kappa factor on chlorine dioxide decomposition and D0-(EP)-D1 bleaching performance for eucalypt pulps, TAPPI JOURNAL April 2016
Journal articles
Magazine articles
Use of fines-enriched chemical pulp to increase CTMP strength, TAPPI Journal April 2021
ABSTRACT: In this study, fines-enriched pulp (FE-pulp)—the fine fraction of highly-refined kraft pulp—was benchmarked against highly-refined kraft pulp (HRK-pulp) as a strength agent in eucalyptus chemithermomechanical pulp (CTMP). Both the FE-pulp and the HRK-pulp were produced from unbleached softwood kraft pulp, and equal amounts of those strength agents were added to the original CTMP, as well as to washed CTMP, where most of the fines had been removed. The effects of the added strength agents were evaluated with laboratory handsheets.The FE-pulp proved to be twice as effective as HRK-pulp. Both HRK-pulp and FE-pulp increased the strength of the CTMP handsheets. The bulk of the handsheets decreased, however, as well as the drainability. The addition of 5% FE-pulp resulted in the same strength increase as an addition of 10% HRK-pulp, as well as the same decrease in bulk and CSF. For the handsheets of washed CTMP, the strengths were not measurable; the CTMP lost the sheet strength when the CTMP-fines content was reduced through washing. The reduced strength properties were compensated for by the addition of chemical pulp fines that proved to be an efficient strength agent. The addition of 5% FE-pulp restored the strength values, and at a higher bulk and higher drainability.
Journal articles
Developing a New Paradigm for Linerboard Fillers, TAPPI JOURNAL March 2008
Developing a New Paradigm for Linerboard Fillers, TAPPI JOURNAL March 2008
Journal articles
Data driven modeling to reduce fossil fuel consumption in a lime kiln integrated with biomass gasifier, TAPPI Journal September 2026
ABSTRACT: Biomass gasification, although already known and applied, is currently being consolidated as a sustainable alternative in the pulp industry, contributing to the reduction of fossil carbon dioxide (CO2) emissions and to the utilization of forest residues. In this context, pulp mills are beginning to adopt biomass gasification within their chemical recovery cycles by integrating the technology with lime kilns. However, further process studies are still needed to support and optimize this application. Thus, the present study aimed to analyze lime mud feed temperature by applying an artificial neural network model to a gasification system integrated with a lime kiln. For this evaluation, 10 periods of system stability throughout 2024 were selected under different operational conditions. Data from 28 potential predictive variables were collected, a total of 348 observations. This dataset was then processed using R software, where data treatment and model dimensionality reduction were performed, resulting in 10 predictive variables between gasifier and kiln. Next, the dataset was randomly divided into training (70% of the observations) and testing data. The established neural network model (using “neuralnet” package) was optimized, resulting in a configuration containing one hidden layer with three neurons. This setup enabled optimal estimation of the flue gas kiln outlet temperature, with mean absolute error (MAE) = 3.0°C and root mean square error (RMSE) = 4.1°C, applying the resilient backpropagation algorithm with backtracking — both below the thermocouple’s measurement error (±5.0°C) for the evaluated average temperature range (668.2°C). When the same dataset was modeled using the resilient backpropagation algorithm without backtracking, even better results were achieved: MAE = 2.5°C and RMSE = 3.7°C. Thus, after evaluating these and other configurations, it was concluded that the best model required 10 predictive variables and the backpropagation algorithm without backtracking to determine flue gas kiln outlet temperature. These results provide a better understanding of how gasifier and kiln variables influence the temperature in the lime kiln, which is essential to improve control and optimize the calcination process, avoiding supplementary fossil fuel consumption.
Journal articles
Biomass gasification for green ammonia production in kraft mills, TAPPI Journal September 2026
ABSTRACT: As the global energy sector transitions toward net-zero emissions, kraft pulp mills present a compelling opportunity to produce green fuels and achieve net-negative emissions by capturing biogenic carbon, helping offset hard-to-abate sectors. This study explores the techno-economics of integrating biomass gasification for green ammonia production within kraft mills, using KraftSIM modeling to evaluate ammonia production, steam balance, emissions, and utility impacts. The proposed design enables energy and water system integration with the existing mill and allows for a gradual scale-up without disrupting the chemistry and operation of the recovery cycle. Across five scenarios representing different biomass gasification rates ranging from 100 to 1000 bone-dry metric tons per day (BDMT/d), the process yields ammonia at approximately 0.51 metric tons per bone-dry metric ton (t/ BDMT), while generating significant low- and medium-pressure steam and hot water that offset mill utility demands. The incineration of pressure swing adsorption tail gas and ammonia plant purge gas in the power boiler reduces biomass combustion and enhances power boiler efficiency. Economic analysis suggests a net revenue potential of approximately CA$380/BDMT, which could increase with the implementation of biogenic carbon pricing. Overall profitability is strongly influenced by biomass procurement costs, electricity prices, and prevailing green fuel and chemical market premium. This work outlines a practical, near-term decarbonization pathway for kraft mills by coupling green fuel production with potential opportunities for carbon removal.
Journal articles
Magazine articles
Corrosion damage and in-service inspection of retractable sootblower lances in recovery boilers, TAPPI Journal October 2021
ABSTRACT: Several reports of accidents involving serious mechanical failures of sootblower lances in chemical recovery boilers are known in the pulp and paper industry. These accidents mainly consisted of detachment and ejection of the lance tip, or even of the entire lance, to the inside of the furnace, towards the opposite wall. At least one of these cases known to the author resulted in a smelt-water explosion in the boiler.In other events, appreciable damage or near-miss conditions have already been experienced. The risk of catastrophic consequences of the eventual detachment of the lance tip or the complete lance of a recovery boiler soot-blower has caught the attention of manufacturers, who have adjusted their quality procedures, but this risk also needs to be carefully considered by the technical staff at pulp mills and in industry committees.This paper briefly describes the failure mechanisms that prevailed in past accidents, while recommending inspection and quality control policies to be applied in order to prevent further occurrences of these dangerous and costly component failures. Digital radiography, in conjunction with other well known inspection techniques, appears to be an effective means to ensure the integrity of sootblower lances in chemical recovery boilers used in the pulp and paper industry.
Journal articles
Magazine articles
Displacement washing of softwood pulp cooked to various levels of residual lignin content, TAPPI Journal September 2021
ABSTRACT: This study investigates the influence of the degree of delignification of kraft spruce pulp cooked at seven different kappa numbers, ranging from 18.1 to 50.1, on the efficiency of displacement washing under laboratory conditions. Although the pulp bed is a polydispersive and heterogeneous system, the correlation dependence of the wash yield and bed efficiency on the Péclet number and the kappa number of the pulp showed that washing efficiency increased not only with an increasing Péclet number, but also with an increasing kappa number. The linear dependence between the mean residence time of the solute lignin in the bed and the space time, which reflects the residence time of the wash liquid in the pulp bed, was found for all levels of the kappa number. Washing also reduced the kappa number and the residual lignin content in the pulp fibers.
Journal articles
Optimization of energy efficiency and condensate production in evaporation plants for a modern softwood pulp mill, TAPPI Journal April 2026
ABSTRACT: To meet the need to further improve thermal efficiency and environmental performance of kraft pulp mills, new systems and techniques have been developed within the evaporation plant. This paper describes these novel approaches and how they were implemented in a project completed in 2018 for a new evaporator and condensate treatment system supplied by Valmet at the SCA Östrand market pulp mill in Sweden. This project was part of a stepwise upgrade of the complete mill to increase the production capacity of the mill from 430,000 to 900,000 air-dried metric tons/year (ADt/y). As part of this upgrade, the mill had the objectives to increase the energy efficiency of the pulp mill and to minimize the air emissions as much as possible, the effluent volume, and the water usage in the mill. The mill also wanted to have the disposal of the biosludge in the black liquor, and the production of tall oil from black liquor soap, liquid methanol, and turpentine. This required that the new evaporation and condensate treatment system be very closely integrated into the other process departments of the mill, including integration of the hot weak black liquor flash vapor from the digester directly into the evaporator train and the production of multiple streams of clean evaporation plant condensate at the correct temperature for the bleach plant. Heat and mass balance calculation values, which were found to do very well in predicting the effect on actual mill operation, are also presented in this paper.
Journal articles
Examination of scoring parameters of corrugated fiberboard, TAPPI Journal August 2026
ABSTRACT: One of the less interrogated aspects of corrugated packaging are scoring and scoring profiles, the intentional localized crushing of flutes to accommodate package folding and closure. This study explores the effect of scoring parameters on box compression test strength (BCT) of two balanced corrugated boards. Scoring differences produced BCT that varied by 10% for one board and less for the other board. Parameters from 4-point bending of scored specimens showed some correlation with BCT, while eccentricity and torsion parameters had less correlation. Different scores produced BCT differences that were not strongly predicted by most standard tests in the current study, implying other tests may be needed to examine the actual boundary conditions on a box during compression. In a few cases, aggressive scoring produced cracked score lines, and those containers had lower BCT than containers with uncracked score lines.
Journal articles
Investigating the causes of severe economizer tube thinning in a spent sulfite liquor (SSL) boiler, TAPPI Journal August 2026
ABSTRACT: In this study, the causes of tube thinning in the economizer of an ammonia-based spent sulfite liquor (SSL) boiler in a Canadian pulp mill are investigated. The tube thinning was most severe in the upper tube rows of the lowest economizer sections where the tube surface temperature ranges between about 180°C and 210°C. The location, the temperature range, and the results of a tube failure analysis indicate that some form of corrosion- erosion is the main cause for the tube thinning. The process is likely initiated by the formation of potassium bisulfate in tube deposits. We hypothesize that some areas in the economizer, including gaps in tube shields, have allowed for temporary buildup of deposits that were not fully removed by sootblowing. Potassium bisulfate is highly hygroscopic, so it readily absorbs moisture, forming an acidic solution leading to corrosion. The corrosion products are removed by the erosive effects of high velocity gas movement, causing the tube thinning. The high-speed fluid flow may be a result of sootblower action and/or enhanced flue gas velocity due to channeling. The tube thinning eventually leads to perforation and leakage.