Search

The use of hollow sphere pigments as strength additives in paper and paperboard coatings—Part 2: Optimization in paperboard formulations for opacity and strength, TAPPI Journal November 2020

ABSTRACT: This report aims to summarize the efforts in testing the properties of coatings for paperboard utilizing hollow sphere pigments (HSPs). HSPs are known to effectively scatter light and replace titanium dioxide (TiO2) in architectural coating formulations. The effect of the particle size and void fraction was evaluated, along with many coating parameters, including level of addition, binder chemistry, and blends of two HSPs. The small HSPs that have optimized voids for scattering light showed equivalent strength to the TiO2-containing control. The strength data was surprising, particularly the improvement in strength for coatings containing large particle size HSPs. Because of this increase in strength, four parts of binder could be removed, which allowed for higher brightness while not compromising other properties, including hot melt glueability. These trends held true using different binder chemistries (styrene acrylic, vinyl acrylic, and styrene butadiene). Upon refining the formulations further, blends of two HSPs showed further benefit.

An analytical method to quantitatively determine the amount of polyamide epichlorohydrin (PAE) in paperboard and white water, TAPPI Journal February 2023

Editorial: Nonwovens sector provides opportunities for professional and advanced textiles growth, TAPPI Journal February 2023

Mechanistic aspects of nanocellulose–cationic starch–colloidal silica systems for papermaking, TAPPI Journal February 2023

A method to produce paperboard with a lightweight low-density coating, TAPPI Journal November 2025

ABSTRACT: In this work, a method is described in which a coating layer is produced that consists of a network of bubble-shaped air-filled voids within the coating. This is accomplished by instantaneously flash-drying all the water in the coating as it exits the application nip. The nip is formed between a polished chrome drum and a deformable press roll. The combination of the drum temperature, nip pressure, and nip width allow for sufficient energy to be transferred to the coating to completely flash-dry the coating material. The pressure within the nip is sufficient to allow the coating to superheat within the nip, then flash boil as it exits the nip. This boiling effect and resulting expansion are constrained by the roll surface, resulting in a coated surface that mirrors the polished chrome surface. The coating immobilizes while in the process of boiling, which preserves the bubble structure. With a coat weight of 5 g/m2, a flat, smooth surface is produced. This process was scaled up to a mill production machine layout and run at speeds as high as 450 m/min.

Editorial: The U.S. pulp & paper industry at a crossroads: Can it lead the bioeconomy

The industry is entering a pivotal moment in which many of us find ourselves engaged in deep soul searching. Since the days of Francis Bacon when the illustrious triumvirate of gunpowder, the compass, and paper were the drivers of civilizations, our community has enjoyed a noble place at the table. Indeed, especially over the last 100 years, pulp and paper has quietly powered communication, commerce, and, more than ever today, packaging, thus representing a steady backbone for the continued stability of many global industries.

Effects of water hardness (CaCl2 addition) on performance of papermaking additives for fine-particle, TAPPI Journal October 2025

Application: A practical take-away message, based on laboratory testing, is that cationic acrylamide-type retention aid is quite tolerant of different water hardness conditions. Such products can promote both retention and drainage in paper machine systems even when operating under very low or very high water hardness conditions, as are often found at mill sites in different regions.

Effect of pulp refining on thixotropy of cellulose fiber suspensions, TAPPI Journal September 2025

ABSTRACT: This paper presents results on the thixotropic behavior of low-consistency bleached eucalyptus fiber suspensions that had been mechanically treated. The pulps were refined in a PFI mill at different numbers of revolutions (0, 3000, and 6000) to study the effect of refining intensity on the viscosity time-response of fiber suspensions. In steady rheological tests, all the suspensions exhibited shear thinning behavior and no significant differences were observed after mechanical treatment. Stepwise experiments showed that viscosity continuously increased with time when shear rate was suddenly reduced. Additionally, a delay in time evolution of viscosity was observed as the pulp was more refined. A stretched exponential model was fitted to the experimental results of viscosity.

Wheat straw as an alternative pulp fiber, TAPPI Journal December 2024

Author: Peter W. Hart | TAPPI J. 19(1): 41(2020) - ABSTRACT: The desire to market sustainable packaging materials has led to an interest in the use of various fiber types as a raw material. It has been suggested that the use of annual crops for partial replacement of wood fiber would result in more sustainable products. Several life cycle analyses (LCA) have been performed to evaluate these claims. These LCAs provided conflicting and contradictory results because of the local conditions and the specific pulping processes investigated. Selected LCAs are reviewed and the underlying reasons for these conflicting results are analyzed.

Review of coating cracking and barrier integrity on paperboard substrates, TAPPI JournalDecember 2024

Authors: Joel C. Panek and Peter W. Hart | TAPPI J. 21(11): 589(2022) - ABSTRACT: Barrier packaging formats are major growth areas for the pulp and paper industry. It is technically challenging to maintain barrier properties during converting and end-use applications. Improved manufacturing capabilities and coating formulation knowledge will help maintain barrier integrity and enable growth of barrier products in challenging applications. These improvements will accelerate product development and commercialization, and allow faster response to product performance issues such as cracking. The literature on coating cracking provides knowledge mostly on the effects of coating formulations and to a lesser extent on substrate effects. Despite a large number of publications dedicated to coating failures, the approach to improve coating cracking remains empirical, and the transferability between studies and to real life applications has not been well established. Model development that successfully predicts commercial performance is in its infancy. However, some of these simplified models do a fairly good job predicting experimental data. The current work reviews the state of understanding as regards coating and barrier cracking and highlights the need for more research on cracking and barrier integrity.