Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Application of spruce wood flour as a cellulosic-based wood additive for recycled paper applications— A pilot paper machine study, TAPPI Journal October 2021
ABSTRACT: This study gives a first insight into the use of wood flour as a plant-based and cellulosic-based alter-native additive for newsprint and paperboard production using 100% recycled fibers as a raw material. The study compares four varieties of a spruce wood flour product serving as cellulosic-based additives at addition rates of 2%, 4%, and 6% during operation of a 12-in. laboratory pilot paper machine. Strength properties of the produced news-print and linerboard products were analyzed. Results suggested that spruce wood flour as a cellulosic-based additive represents a promising approach for improving physical properties of paper and linerboard products made from 100% recycled fiber content. This study shows that wood flour pretreated with a plant-based polysaccharide and untreated spruce wood flour product with a particle size range of 20 μm to 40 μm and 40 μm to 70 μm can increase the bulk and tensile properties in newsprint and linerboard applications.
Journal articles
Magazine articles
Corrosion damage and in-service inspection of retractable sootblower lances in recovery boilers, TAPPI Journal October 2021
ABSTRACT: Several reports of accidents involving serious mechanical failures of sootblower lances in chemical recovery boilers are known in the pulp and paper industry. These accidents mainly consisted of detachment and ejection of the lance tip, or even of the entire lance, to the inside of the furnace, towards the opposite wall. At least one of these cases known to the author resulted in a smelt-water explosion in the boiler.In other events, appreciable damage or near-miss conditions have already been experienced. The risk of catastrophic consequences of the eventual detachment of the lance tip or the complete lance of a recovery boiler soot-blower has caught the attention of manufacturers, who have adjusted their quality procedures, but this risk also needs to be carefully considered by the technical staff at pulp mills and in industry committees.This paper briefly describes the failure mechanisms that prevailed in past accidents, while recommending inspection and quality control policies to be applied in order to prevent further occurrences of these dangerous and costly component failures. Digital radiography, in conjunction with other well known inspection techniques, appears to be an effective means to ensure the integrity of sootblower lances in chemical recovery boilers used in the pulp and paper industry.
Journal articles
Corrosion Monitoring and Root Cause Identification in High Solids Concentrators
Black liquor high solids (about 80%) concentrators have often been found to suffer from aggressive corrosion. In particular, the first and second effect bodies are susceptible to corrosion attacks resulting in tube leaks and wall thinning, which limit the availability and lifetime of evaporator lines. Corrosion dynamics and construction materials have been studied extensively within the pulp and paper industry to understand the corrosion process. However, it has been challenging to identify root causes for corrosion, which has limited proactive measures to minimize corrosion damage. Corrosion of the first phase concentrator was studied by defining the potential regions for passive area, stress corrosion cracking, pitting corrosion, and general corrosion. This was achieved by using a technique called polarization scan that reveals ranges for the passive area in which the equipment is naturally protected against corrosion. The open circuit potential, also known as corrosion potential, and linear polarization resistance of the metal were monitored online, which allowed for definition of corrosion risks for stainless steel 304L and duplex stainless steels 2205 and SAF 2906. An online temperature measurement added insight to the analysis. A process diagnostics tool was used to identify root causes of the corrosion attacks. Many of the root causes were related to process conditions triggering corrosion. Once the metal surface was activated, it was difficult to repassivate the metal naturally unless a sufficient potential range was reached.
Journal articles
Black liquor spray properties in-furnace conditions for swirl cone nozzles, TAPPI Journal July 2026
ABSTRACT: Recovery boiler furnace operation is controlled for high chemical recovery, high steam production, and low emissions. Good control allows long runs with minimum cleaning without expensive shutdowns. An essential variable affecting boiler operation is black liquor spraying into the furnace. Poorly controlled black liquor spraying causes difficulties, e.g., in chemical recovery, fouling of heat transfer surfaces, and decreased energy production. A challenging measurement strategy with three different swirl cone nozzles . types A, C, and T . was carried out at a mill in the United States. Black liquor spray properties were measured under in-furnace conditions for flow rates of 2.0 L/s to 3.0 L/s. Three spraying temperatures of 119™‹C, 122™‹C, and 126™‹C, which were 2™‹C, 5™‹C, and 9™‹C above the boiling point (ƒ¢Te), were tested. These flow rates and temperatures are typical for industrial nozzle sizes with exit orifice sizes of 17 mm and 22 mm. An imaging method to measure droplet size in a highly challenging furnace environment was developed. Droplet volume median diameter (Dv50) for nozzles A, C, and T varied between 7 mm to 4 mm, 7 mm to 5 mm, and 8 mm to 6 mm, depending on the flow rate and temperature. The high number of droplets detected by the analysis program enabled data fitting into statistical correlations. The size and width parameters for the Rosin™]Rammer droplet size distribution function could be defined. The droplet size distribution was found to be surprisingly wide, probably because of swollen droplets. Spray velocity was measured in two locations, 5 cm from the nozzle and 1.8 m from the nozzle. Near the nozzle, the average velocity increased from 7.3 m/s to 13 m/s when the flow rate was increased from 2 L/s to 3 L/s. Increase of black liquor temperature increased spray velocity in most of the cases. At the distance of 1.8 m from the nozzle, average spray velocities varied between 4.0 m/s to 11 m/s, depending on nozzle geometry, flow rate, and temperature. The opening angles of the spray for nozzles A and C varied between 57™‹ to 78™‹. The opening angle of nozzle T with flow guide varied between 48™‹ to 56™‹. The highest penetration of the spray was estimated for nozzle T because of the narrow spray and large droplets.
Journal articles
Exploratory study on how sub-ply fiber orientation affects t
ABSTRACT: The transition to 100% biobased packaging presents considerable challenges, particularly in the development of a petroleum-free barrier. Generally, biobased barriers exhibit lower flexibility compared to traditional barriers, thereby increasing the risk of cracking during the converting process. The present study examines the possibility of optimizing the substrate to reduce cracking in brittle barriers. Five three-ply composites were fabricated using commercial paperboard to enable a composite with different fiber orientation in the individual plies. The different orientations achieved varying mechanical properties, including strain-atbreak and folding resistance, with a ranking that is comparable to a standard multi-ply paperboard. The composites were subjected to creasing at five distinct depths to assess the area percent of barrier cracks across the crease bead. Micro-cracks appeared on the surface before larger coating cracks were registered. As expected, the area percent of barrier cracks increased significantly with greater creasing depths. The orientation of the bulky middle ply showed little difference in the cracking propensity. However, by replacing the stiffer bottom ply with a ply of lower stiffness, the cracking propensity was significantly reduced without a substantial loss in mechanical properties. Hence, these findings indicate that it is possible to reduce the cracks in the barrier by modifying the fiber orientation in the different plies.
Journal articles
Improving barrier performance of coated paper and paperboard
ABSTRACT: Market demand for barrier coated packaging paper and paperboard has been on a steady rise and is forecasted to further increase. As a result, there is a continued interest in improving barrier coating functionalities, which is currently an active area of investigation. In this work, a multi-layer approach was adopted that involved applying a biowax emulsion, latex, or a combination of biowax and latex top coating layer onto the kaolin/latex (20/80, 50/50, 65/35, or 70/30) precoated solid bleached sulfate (SBS) paperboard. Our main objective was to demonstrate the effect of these top coating layers on various barrier properties, especially water vapor transmission rate (WVTR) at high relative humidity (RH) and high temperature (90% RH; 38°C), known as tropical/jungle test conditions. While the top coat with latex and/or biowax showed dramatic improvement in both water resistance (Cobb) and WVTR, the biowax coating increased contact angle significantly compared to the latex top coat. Contact angle increased from about 65° for the latex top coat to as high as 96° for the biowax top coat. Generally, it is much more difficult to improve WVTR at the jungle conditions below 100 g/m2/day, even with the high aspect ratio platy pigment. However, using the coating strategies adopted in this study, we were able to achieve WVTR values notably below 50 g/m2/day at the tropical test conditions, as well as significant improvements in regard to fold crack barrier integrity at high kaolin clay usage.
Journal articles
Prediction of residual calcium carbonate (CaCO3) in the lime
ABSTRACT: In a kraft pulp mill, the rotary lime kiln is responsible for converting calcium carbonate (CaCO3) into calcium oxide (CaO) to be reused in the causticizing plant. An important parameter of the calcination efficiency and the product quality is the amount of CaCO3 not converted to CaO, commonly defined as residual carbonate. This parameter is usually determined through laboratory analysis, which introduces delays in process control and limits the ability to make timely operational adjustments. This work presents a predictive model that functions as a soft sensor for the residual carbonate in a lime kiln of a Brazilian kraft pulp mill. This model was able to estimate residual CaCO3 every 30 min using routinely measured online process variables, which is a considerable reduction from the 6-h average laboratory measurement. The correlation coefficient (r) between the model predictions and the mill values was 0.83, with a mean absolute error (MAE) of 0.33%. Considering the effect of the residence time throughout the lime kiln proved to be decisive in obtaining a satisfactory prediction result. After model validation, a variable importance analysis showed that the carbon monoxide (CO) concentration in the stack flue gas (in ppm), secondary air temperature (in oC), and fan speed (in %) were the most influential variables in predicting the residual carbonate content. Combined with commonly used operation expertise, this subset of variables can serve as additional information to achieve smoother lime kiln operation.
Journal articles
Magazine articles
The use of minerals in fiber-based packaging and pulp molding, TAPPI Journal January 2024
ABSTRACT: Minerals are widely used in the pulp and paper industry for aiding the processing, economics, and final quality of fiber-based products. Among these, calcium carbonate, talc, and kaolin are widely used as fillers, and these can have varying brightness, particle size distributions, and aspect ratios. For the molded fiber area, these minerals can raise the solids content of the pulp mixture and improve throughput and lower energy requirements for drying. Talc is also widely used as a process control agent, picking up pitch and stickies and improving productivity by lowering machine cleaning time.The replacement of single use plastic with fiber-based replacements is a global trend; however, it does come with some significant challenges, such as grease and moisture proofing. Previously, per- and polyfluoroalkyl substances (PFAS) have been used to provide functions such as water and grease repellency, but regulatory demands have seen its demise in the packaging industry. Therefore, water holdout is now generally achieved by addition of alkyl ketene dimer (AKD) sizing. Wax additives are being developed and tested as PFAS replacements for oil and grease resistance. Rather than strongly repelling lipids from the fiber surface, these PFAS alternatives restrict flow pathways and react with food oils to alter their flow characteristics to prevent penetration through the substrate. During studies incorporating both PFAS substitutes and minerals, no detrimental interactions were observed. This paper addresses the different needs of the molded fiber market by including mineral fillers in molded fiber articles and will be presented as a series of different case studies. In all studies, we show that the trends observed when mineral filler is added to molded fiber are broadly similar to those seen in conventional paper and paperboard applications. Mineral addition in all studies gave improvements in productivity and optical appearance. With its organophilic surface, hydrophobic talc had the additional advantage of pitch and sticky control, and although a small decrease in strength was always observed when filler was added, the final articles still retained sufficient strength for their particular application. This small strength reduction should be balanced against the productivity gains.
Journal articles
Physico-mechanical and ethylene scavenging properties of active packaging from Bambusa fibers modified with TiO2 /Cu2O composite, TAPPI Journal February 2026
ABSTRACT: The physico-mechanical and ethylene scavenging properties of active packaging consisting of paper prepared from bamboo (Bambusa vulgaris) fibers loaded with varying concentrations of nano titanium dioxide/cuprous oxide (TiO2/Cu2O) composite was investigated for its ability to delay ripening of Philippine climacteric fruits. Tests of paper containing 1% to 5% TiO2/Cu2O showed no or limited negative impact on its physical, optical, and mechanical properties. Images from a field emission scanning electron microscope equipped with energy-dispersive X-ray spectroscopy (FESEM-EDS) showed dispersion and agglomeration of TiO2/Cu2O nanoparticles on the paper surface. The percent weight of titanium and copper increased with increasing metal oxide composite concentration used in this study. Attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy indicated small shifts in band intensity at 3330 cm-1 and 1100 cm-1 in the hydroxyl (O-H) and C-O regions, respectively, suggesting possible chemical or physical interactions between the metal oxide and paper. Contact angle measurement suggest- ed that TiO2/Cu2O nanoparticles may have imparted paper hydrophobicity at 3% & 5% concentration, possibly through increased microscale roughness. The ethylene scavenging experiment indicated that there was a significant delay in the ripening process of mango and tomato when packed in paper doped with 3% and 5% TiO2/Cu2O. The fruits were greener with a firmer texture compared with untreated control after three days of storage under natural light and ambient condition. The preliminary results suggested that 3% &5% TiO2/Cu2O active packaging modification can remove ethylene from the fruit's storage environment, extending shelf life and maintain quality for three days. This simple technique could have potential economic benefits for the fruit industry by directly reducing post-harvest waste, and the delayed ripening could provide flexibility in supply chain management.
Journal articles
Non-process elements in the lime cycle: New findings regarding NPE distribution and lime mud filterability, TAPPI Journal July 2026
ABSTRACT: Proper functioning of the recausticizing cycle is crucial for securing a stable white liquor supply for a pulp mill. Common runnability problems in the modern lime cycle, such as low filterability and poor dewatering of lime mud, high dead load, or ring formation in the lime kiln, are often caused by accumulation of non-process elements (NPEs). This project attempted to verify the traditional rules of thumb regarding the chemical behavior of NPEs: magnesium (Mg), aluminum (Al), silicon (Si), phosphorus (P), zinc (Zn), manganese (Mn), iron (Fe), copper (Cu), barium (Ba), cadmium (Cd), and lead (Pb) in the causticizing reaction, and to investigate the reasons behind poor lime mud filterability. First, a standardized method for measuring filterability of lime mud was developed. Next, a series of recausticizing experiments, followed by immediate filtration trials, was conducted using mill green liquors, laboratory-made synthetic green liquor, reburned lime/makeup mix, and extra NPE additions. It was found that sodium (Na), potassium (K), and sulfur (S) followed the liquid phase, as expected, while Mg, P, and Ba, but also Pb, Cu, and Cd, showed low solubility and accumulated in the lime mud. The Si and Al accumulated in the lime mud even though the soluble content in liquor was high, while the behavior of Mn, Fe, and Zn was more complex. Based on these results, tentative solubility limits for NPEs were suggested as a first estimate for the maximum possible concentrations of NPEs in mill white liquor. The causticization-filtration experiments revealed that overliming and high content of Mg in green liquor clearly led to lower filterability, but our addition of Si did not have such an effect. As differences in particle size and size distribution have a certain impact on the filtration resistance, the lime mud sedimentation behavior, combined with other characterization methods, might be used as an indication for the filterability. Finally, a list of recommendations for pulp mills was formulated that starts with establishing a comprehensive standard for a lime mud with good filterability. This standard can be used as a benchmark for comparison any time a lime cycle runnability problem is identified.