Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Modeling the influence of rheology on smooth rod coating systems, TAPPI Journal November 2022
ABSTRACT: Rod coating methods are of interest for the application of barrier coatings, especially at off-line facilities that may run at moderate speeds and narrow web widths. At lower line speeds and lower coating solids, it is difficult to achieve good coat weight control because of poor loading of the rod. While there is extensive literature available about blade and roll coating, there seems to be less reported on the rod loading of smooth rods to obtain various coat weights. Much of the work is around metering rods working on applicator rolls at high speeds that are associated with the metered size press, with a focus on ribbing instabilities. This work employs a simplified model, neglecting some complex features of rubber deformation and film split, to estimate the influence of the process parameters such as speed, rod diameter, viscosity, and rod loading on the coat weight obtained. As found in practice, at low speed and low viscosities, the coat weight-load curve is steep, leading to poor control of the coat weight and coat weight uniformity. If the viscosity is increased, the curve is modified, and control is possible with rod loading in a normal range. For shear thinning fluids described by the Carreau model, the power law index and other parameters need to be in the correct range to obtain the desired effect. Modeling predictions show a steeper dependence of coat weight with rod pressure when compared to pilot coater data. This may be caused by missing details in the mechanical loading of the rod related to tube pressure or from neglecting the impact of filter cake formation of the applied coating in the model.
Journal articles
Magazine articles
Boosting the elongation potential of paper by mechanical refining and additives, TAPPI JOURNAL September 2018
Boosting the elongation potential of paper by mechanical refining and additives, TAPPI JOURNAL September 2018
Journal articles
Magazine articles
Mineral/microfibrillated cellulose composite materials: High performance products, applications, and product forms, TAPPI JOURNAL September 2018
Mineral/microfibrillated cellulose composite materials: High performance products, applications, and product forms, TAPPI JOURNAL September 2018
Journal articles
Magazine articles
Black liquor evaporators upgrade — How many effects?, TAPPI Journal April 2023
ABSTRACT: Black liquor evaporation is generally the most energy intensive unit operation in a pulp and paper manufacturing facility. The black liquor evaporators can represent a third or more of the total mill steam usage, followed by the paper machine and digester. When considering an evaporator rebuild or a new system, the key design question is how many effects to include in the system. The number of effects is the main design feature that deter-mines the economy of the system and the steam usage for a given evaporation capacity. A higher number of effects increases steam economy and reduces energy cost to a point, but additional effects also have higher initial capital cost and increased power costs. This research paper uses life-cycle cost analysis (LCCA) as a method to determine the optimum number of evaporator effects for a new evaporator system. The same basic principles and method can also apply to existing evaporator rebuild projects.
Journal articles
Magazine articles
Dynamic CFD modeling of calcination in a rotary lime kiln with an external dryer, TAPPI Journal August 2023
ABSTRACT: Mid-kiln ring formation is a problem in lime kilns that may be related to fluctuations in the start location of calcination. To calculate fluctuations in bed and gas temperature profiles within a lime kiln with an external dryer, a dynamic two-dimensional (2D) axisymmetric computational fluid dynamics (CFD) gas model with a methane burner implemented in ANSYS Fluent, coupled by mass and heat balances to a one-dimensional (1D) bed model, was developed. The dynamic model was used to calculate changes in the location where calcination starts with fluctuations in operational conditions using pulp mill data. This model simulates radiative, convective, and conductive heat transfer between the gas, wall, and bed to determine the axial bed temperature in the kiln. The calcination reaction is described using a shrinking core model that allows for the prediction of the location at which calcination begins and the degree of calcination achieved. The solid motion within the kiln is modeled using Kramer’s equation modified for transient response. Steady-state and dynamic simulation results were compared to data from an industrial dry lime kiln, and good agreement was found. A sensitivity analysis was also performed to provide insight on how operating conditions and model variables impact the calcination location and degree of calcination. Of the variables examined, the fuel rate and the feed temperature had the largest impact on both the calcination location and degree of calcination in the kiln. Model predictions of a period of ring formation in the industrial kiln showed that the start location of calcination fluctuated by more than 2 m on either side of the mean of regular operation, warranting further investigation of the importance of these fluctuations on mid-kiln ring formation.
Journal articles
Magazine articles
Totally chlorine-free peracetic acid pulping for nanocellulose isolation from hemp and poplar, TAPPI Journal August 2023
ABSTRACT: Nanocellulose is a promising and sustainable feedstock for developing advanced and functional materials. However, the characteristics of nanocellulose, such as crystallinity, surface energy, and aspect ratio, can vary depending on biomass source and pretreatment methods, leading to variable performance of the nanocellulose-based materials. In this study, cellulose nanocrystals (CNCs) were isolated from hemp and poplar using totally chlorine free (TCF) peracetic acid and sodium chlorite delignification and bleaching pretreatments to probe the influences of biomass source and treatment methods on the isolation and characteristics of CNCs. Our results showed that hemp and poplar were almost completely delignified by peracetic acid treatment, whereas sodium chlorite treatment left 5%•6% lignin in the pulp. The yields of CNCs from raw hemp and poplar biomass ranged from 9.8% to 21.9% and 10.9% to 28.3%, respectively, depending on the treatment methods. The dimensions of CNCs from TCF-treated biomass generally maintained a larger width and aspect ratio than those from sodium chlorite-treated biomass. The poplar-derived CNCs exhibited slightly higher crystallinity of 53%•58% than hemp-derived CNCs of 49%•54%. The zeta potential of the CNCs, ranging from -20.1 mV to -31.1 mV, ensured a well-dispersed aqueous solution. The surface energy (dispersive energy of 40•80 mJ/m2 and specific energy of 2•10 mJ/m2), water interaction, and thermal stability of the CNCs were comparable, regardless of the biomass source and pretreatment methods. Our finding suggests that the TCF technique with peracetic acid treatment is a promising delignification and bleaching approach to obtain cellulose-rich pulps from herbaceous and hardwood biomass for nanocellulose isolation.
Journal articles
Optimization of energy efficiency and condensate production in evaporation plants for a modern softwood pulp mill, TAPPI Journal April 2026
ABSTRACT: To meet the need to further improve thermal efficiency and environmental performance of kraft pulp mills, new systems and techniques have been developed within the evaporation plant. This paper describes these novel approaches and how they were implemented in a project completed in 2018 for a new evaporator and condensate treatment system supplied by Valmet at the SCA Östrand market pulp mill in Sweden. This project was part of a stepwise upgrade of the complete mill to increase the production capacity of the mill from 430,000 to 900,000 air-dried metric tons/year (ADt/y). As part of this upgrade, the mill had the objectives to increase the energy efficiency of the pulp mill and to minimize the air emissions as much as possible, the effluent volume, and the water usage in the mill. The mill also wanted to have the disposal of the biosludge in the black liquor, and the production of tall oil from black liquor soap, liquid methanol, and turpentine. This required that the new evaporation and condensate treatment system be very closely integrated into the other process departments of the mill, including integration of the hot weak black liquor flash vapor from the digester directly into the evaporator train and the production of multiple streams of clean evaporation plant condensate at the correct temperature for the bleach plant. Heat and mass balance calculation values, which were found to do very well in predicting the effect on actual mill operation, are also presented in this paper.
Journal articles
A systems approach for process debottlenecking towards a sustainable pulp and paper industry, TAPPI Journal April 2026
ABSTRACT: Increasing the competitiveness of the pulp and paper industry requires an effective optimization of its existing assets in line with a long-term vision for process transformation, production upgrade, and product diversification. Currently, pulp production increase is one of the main sources of additional revenue for the kraft industry. Likewise, energy efficiency is often employed as a cost-effective approach to reduce operating costs, enhancing the possibilities to lower fossil fuel consumption and contributing to a low-carbon economy. On the other hand, reaching higher production targets and facilitating process transformation, such as biorefinery implementation, heavily depend on the status and performance of a mill’s current infrastructure; therefore, a system analysis is needed to assess the new production requirements, the bottlenecks, and the interactions across departments. In order to obtain practical improvement solutions, direct and indirect impacts on process performance and resource utilization should be considered. This work provides an overview of the key challenges that need to be addressed for production increase and energy efficiency improvement. The methodology starts by a scope analysis for debottlenecking and screening capacity limitations vs. mill targets, followed by their ranking (bottleneck ranking diagram). Benchmarking, gap analysis, and root-cause techniques are applied to diagnose system inefficiencies. This mill-wide debottlenecking assessment is then used to guide the selection of a long-term sustainable operation and design a portfolio of improvement projects by avoiding cross effects of the short-term projects on the long term. A case study of a kraft pulp mill is used to illustrate the proposed methodology.
Journal articles
Magazine articles
Formic acid pulping process of rice straw for manufacturing of cellulosic fibers with silica, TAPPI Journal August 2021
ABSTRACT: Emerging technology has the potential to develop entirely new approaches for producing cellulose fiber-based materials along with fuels and chemical raw materials like lignin and furfural. Rice straw is a rich source of cellulosic fibers and inorganic micronic-sized particles termed as ash. They can prove helpful in development of new or enhanced agricultural residue-based materials and products that offer cost effective substitutes for nonrenewable materials used in different domestic and industrial applications. Lignocellulose is an abundant material that is submicronic at the basic level. Rice straw is a fibrous lignocellulosic material obtained as agricultural residue, but it differs from most crop residues in its high content of silicon dioxide (SiO2). Ash content on a dry weight basis ranges from 13% to 20%, varying according to the state of conservation of the straw after harvest. The ash in rice straw has nearly 75% SiO2. The particle size analysis shows variation from a few microns to hundreds of microns for inorganic residues left after burning at high temperatures above 550°C. Proximate analysis of rice straw shows that it contains 54% to 56% holocellulose and 15% to 18% lignin, both of which are natural biopolymers. The compound analysis shows the different compounds present in rice straw ash.Rice straw is available in hundreds of million tons in India and other Asian countries, so suitable technologies are required to convert rice straw from a biomass waste to useful bioproducts like pulp, paper, and paperboard. This research paper is intended to obtain pulp with fibers having inherent silica present in it to give high opacity paper and better bonding between fibers.
Journal articles
Magazine articles
Can carbon capture be a new revenue opportunity for the pulp and paper sector?, TAPPI Journal August 2021
ABSTRACT: Transition towards carbon neutrality will require application of negative carbon emission technologies (NETs). This creates a new opportunity for the industry in the near future. The pulp and paper industry already utilizes vast amounts of biomass and produces large amounts of biogenic carbon dioxide. The industry is well poised for the use of bioenergy with carbon capture and storage (BECCS), which is considered as one of the key NETs. If the captured carbon dioxide can be used to manufacture green fuels to replace fossil ones, then this will generate a huge additional market where pulp and paper mills are on the front line. The objective of this study is to evaluate future trends and policies affecting the pulp and paper industry and to describe how a carbon neutral or carbon negative pulp and paper production process can be viable. Such policies include, as examples, price of carbon dioxide allowances or support for green fuel production and BECCS implementation. It is known that profitability differs depending on mill type, performance, energy efficiency, or carbon dioxide intensity. The results give fresh understanding on the potential for investing in negative emission technologies. Carbon capture or green fuel production can be economical with an emission trade system, depending on electricity price, green fuel price, negative emission credit, and a mill’s emission profile. However, feasibility does not seem to evidently correlate with the performance, technical age, or the measured efficiency of the mill.