Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Synthesis of filtrate reducer from biogas residue and its application in drilling fluid, TAPPI Journal March 2020
ABSTRACT: Biogas residues (BR) containing cellulose and lignin are produced with the rapid development of biogas engineering. BR can be used to prepare the filtrate reducer of water-based drilling fluid in oilfields by chemical modification. BR from anaerobically fermenting grain stillage was alkalized and etherified by caustic soda and chloroacetic acid to prepare filtrate reducer, which was named as FBR. The long-chain crystalline polysaccharides were selected as dispersing agents (DA), and the water-soluble silicate was used as the cross-linking agent. After the hot rolling of FBR in saturated saltwater base mud for 16 h at 120°C, the filtration loss was increased from 7.20 mL/30 min before aging to 8.80 mL/30 min after aging. Compared with the commercial filtrate reducers, FBR had better tolerance to high temperature and salt, and lower cost.
Journal articles
Magazine articles
Multiple recycling of paperboard: Paperboard characteristics and maximum number of recycling cycles— Part I: Multiple recycling of corrugated base paper, TAPPI Journal November 2019
ABSTRACT: Paper for recycling is an important fiber source for the production of corrugated base paper. The change in production capacity toward more and more packaging papers affects the composition of paper for recy-cling and influences the paper quality. This research project investigated the influence of the multiple recycling of five different corrugated base papers (kraftliner, neutral sulfite semichemical [NSSC] fluting, corrugating medium, testliner 2, and testliner 3) on suspen-sion and strength properties under laboratory conditions. The corrugated board base papers were repulped in a low consistency pulper and processed into Rapid-Köthen laboratory sheets. The sheets were then recycled up to 15 times in the same process. In each cycle, the suspension and the paper properties were recorded. In particular, the focus was on corrugated board-specific parameters, such as short-span compression test, ring crush test, corrugat-ing medium test, and burst. The study results indicate how multiple recycling under laboratory conditions affects fiber and paper properties.
Journal articles
Functional surfaces produced by foam coating, TAPPI JOURNAL
Functional surfaces produced by foam coating, TAPPI JOURNAL August 2016
Journal articles
Acoustic analysis of recovery boiler dissolving tank operati
Acoustic analysis of recovery boiler dissolving tank operation and smelt shattering efficiency, TAPPI JOURNAL September 2016
Journal articles
Analysis of wrinkle formation and propagation during paperboard deep drawing, TAPPI Journal October 2026
ABSTRACT: Paper-based packaging is becoming increasingly important as a sustainable alternative to plastics. Among forming processes, deep drawing is particularly promising due to its high cost-effectiveness, short processing times, and suitability for large-scale production. A major challenge, however, lies in the formation of wrinkles, which impair the visual quality, functional performance, and dimensional stability of the packaging, thereby affecting subsequent processes such as filling, printing, and sealing. This study focuses on analyzing the occurrence and propagation of wrinkles during the deep drawing of paperbased materials to derive fundamental insights and strategies for prevention. The wrinkles arise from tangential compressive stresses in the flange and the material’s limited thickening, leading to local stability failures once a critical stress threshold is exceeded. A combined approach of experimental investigations, numerical simulations, and analytical considerations was used to examine a rotationally symmetrical part. A transparent die enabled spatial observation of wrinkle initiation and growth. First, wrinkles were found to typically initiate in the cross direction (CD), while most wrinkles develop in the machine direction (MD). By comparing analytically and numerically determined stress distributions, the mechanisms of wrinkle formation can be understood both locally and temporally, thereby enabling the prediction of wrinkle occurrence.
Investigating the causes of severe economizer tube thinning in a spent sulfite liquor (SSL) boiler, TAPPI Journal August 2026
ABSTRACT: In this study, the causes of tube thinning in the economizer of an ammonia-based spent sulfite liquor (SSL) boiler in a Canadian pulp mill are investigated. The tube thinning was most severe in the upper tube rows of the lowest economizer sections where the tube surface temperature ranges between about 180°C and 210°C. The location, the temperature range, and the results of a tube failure analysis indicate that some form of corrosion- erosion is the main cause for the tube thinning. The process is likely initiated by the formation of potassium bisulfate in tube deposits. We hypothesize that some areas in the economizer, including gaps in tube shields, have allowed for temporary buildup of deposits that were not fully removed by sootblowing. Potassium bisulfate is highly hygroscopic, so it readily absorbs moisture, forming an acidic solution leading to corrosion. The corrosion products are removed by the erosive effects of high velocity gas movement, causing the tube thinning. The high-speed fluid flow may be a result of sootblower action and/or enhanced flue gas velocity due to channeling. The tube thinning eventually leads to perforation and leakage.
Image classification of the furnace bed height in recovery boilers, TAPPI Journal July 2026
ABSTRACT: The goal of this study is to develop an approach for classifying char bed height in a recovery boiler during operation. The resulting classified images form a dataset that can be used by the mill to support operational improvements. The study integrates data from the digester, evaporation plant, recovery boiler, and recausticizing plant, along with the classified image data. A convolutional neural network (CNN) was trained on bed camera images that were manually annotated to classify furnace bed height. The model was then used to generate a binary bedheight parameter over a 16-month period, and an extreme gradient boosting (XGBoost) model was applied to identify relationships with operating parameters across the recovery cycle. The outcomes of this research may offer deeper insights into the processes underlying bed dynamics. Ultimately, the developed system may serve as a tool for optimizing bed conditions and supporting stable combustion.
Journal articles
Acoustic analysis of recovery boiler dissolving tank operati
Acoustic analysis of recovery boiler dissolving tank operation and smelt shattering efficiency, TAPPI JOURNAL September 2016
Journal articles
Magazine articles
Critical parameters for tall oil separation I: The importance of ration of fatty acids to rosin acids, TAPPI Journal September 2019
ABSTRACT: Tall oil is a valuable byproduct in chemical pulping of wood, and its fractions have a large spectrum of applications as chemical precursors, detergents, and fuel. High recovery of tall oil is important for the economic and environmental profile of chemical pulp mills. The purpose of this study was to investigate critical parameters of tall oil separation from black liquor. To investigate this in a controlled way, we developed a model test system using a “synthetic” black liquor (active cooking chemicals OH- and HS- ions), a complete process for soap skimming, and determination of recovered tall oil based on solvent extraction and colorimetric analysis, with good reproducibility. We used the developed system to study the effect of the ratio of fatty acids to rosin acids on tall oil separation. When high amounts of rosin acids were present, tall oil recovery was low, while high content of fatty acids above 60% significantly promoted tall oil separation. Therefore, manipulating the content of fatty acids in black liquor before the soap skimming step can significantly affect the tall oil solubility, and hence its separation. The findings open up chemical ways to improve the tall oil yield.
Journal articles
Magazine articles
A new technique for the measurement of show-through mottle of fine paper, TAPPI Journal September 2019
ABSTRACT: Mottling within print-through and show-through is caused by the variability of the local optical properties of the sheet. This mottling is visually disturbing and a mark of poor paper quality. The ability to predict print-through mottle of printed paper by measuring show-through mottle on the unprinted sheet would be a valuable asset for paper machine control.We examined the relationship between print-through mottle and show-through mottle. We worked with nine samples of 60 lb. uncoated fine paper (90 g/m2), from various North American paper companies, that were printed on an offset press, 400K (400% Black), on both sides. A show-through mottle instrumental determination technique was developed using an existing Fast Fourier Transform-based algorithm. The nine samples examined were ranked similarly by the visual evaluation of print-through mottle and by the instrumental determination of show-through mottle. We thus established that show-through on the unprinted sheet can be used as a reliable predictor of print-through, therefore saving time and money for papermakers. We also found a significant two-sidedness in show-through for some of the samples.