Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Energy saving potential of interstage screen fractionation for production of board grade BCTMP, TAPPI Journal August 2023
ABSTRACT: Over the last few decades, the continuing decline in mechanical pulp-based grades has led pulp producers to modify operations and implement measures to reduce production costs in order to stay competitive. In spite of a considerable effort to reduce energy consumption, the latter is still a major portion of production costs in the process of making bleached chemithermomechanical pulp (BCTMP). In this study, we evaluated the impact of interstage screening fractionation (ISSF) and secondary refining strategy for producing BCTMP with the objective of reducing refining energy consumption while maintaining or improving bulk and strength properties. In the first step and to establish a baseline for a mill’s existing configuration, the collected primary refined pulp and reject streams from the ISSF were refined in a high consistency (HC) refiner to target freeness levels. The accepts and refined rejects streams were recombined, and their properties were compared to those of the refined primary pulp. The results showed that, at a given freeness of 400 mL and compared to the control case (without fractionation), the ISSF using an 0.070 in. basket followed by rejects refining could lead to about 25% energy saving in the second stage HC refining. Handsheet properties showed that utilization of ISSF could produce BCTMP with higher bulk and similar average fiber length and tear index. However, a slight reduction in tensile strength was observed. In the second set of trials, the primary refined pulp and the rejects from the ISSF using the 0.070 in. basket were refined by a low-consistency (LC) refiner. The results showed that, at the same freeness of 400 mL and compared to refined primary pulp, the ISSF saved about 26% in net LC refining energy. At a specific edge load (SEL) of 0.4 J/m, the produced pulp had similar bulk and strength properties compared to those of the control sample. A higher SEL of 0.6 J/m in LC refining could further decrease net refining energy consumption; however, it also led to reduction in fiber length, bulk, and strength properties.
Journal articles
Magazine articles
Value creation by converting pulp mill flue gas streams to green fuels, TAPPI Journal March 2023
ABSTRACT: Climate change mitigation induces strong growth in renewable electricity production, partly driven by shifts in environmental policies and regulation. Intermittent renewable electricity requires supporting systems in the form of sustainable hydrocarbon chemicals such as transportation fuels. Bulk chemical production fits well into a pulp mill environment, given their large volumes, stable operation, and ample supply of biomass-based carbon feed-stock in the form of flue gases. Until now, the utilization of the flue gases from conventional operation of a pulp mill has received little attention. Harnessing these flue gases into usable products could offer additional value to mill operators, while also diversifying their product portfolio. However, electricity-based fuels and products require extra energy in the conversion step and may not be commercially competitive with current fossil products under the current regulation. There might also be uncertainties about future commodity prices. Thus, the objective of this study is to estimate the economic competitiveness and the added value of selected side products that could be produced alongside conventional pulp and paper products. A typical modern pulp mill is modeled in different product configurations and operational environments, which allows testing of various development paths. This illustrates how the overall energy and mass balance of a pulp mill would react to changes in different final products and other parameters. The focus of the study is in synthetic methanol, which is produced from flue gases and excess resources from the mill, with minimal interference to the pulping process. The results aid in assessing the necessity and magnitude of a premium payment for subsidizing green alter-natives to replace current fossil fuels and chemicals. Additionally, the results function as an indicator of the development state of the pulp and paper industry in the turmoil of climate change regulation. The results indicate that power-to-X systems offer one more viable pathway alternative for broadening the product portfolio of the pulp and paper sector, as well as opening new flexibility measures and services to grid stabilization. Market conditions were found to have a significant impact on the perceived profitability.
Journal articles
Paper strength factors in systems with nanofibrillated cellulose, cationic starch, colloidal silica, cationic acrylamide copolymer, and hydrodynamic shear, TAPPI Journal May 2025
ABSTRACT: Laboratory paper sheets were formed by first pretreating nanofibrillated cellulose (NFC) with cationic starch at the 5% level by mass. The treated NFC was then added to stock prepared from 100% recycled copy paper. The combined furnish was next optionally treated with a cationic retention aid (cPAM, 0.1%) and then colloidal silica (0.1% or 0.2%). Vacuum dewatering, fine-particle retention, and several paper properties were studied as a function of the colloidal silica level (zero, 1%, and 2%) and at different levels of shear stress applied just before forming the sheets. Dewatering and strength results were generally more favorable when using a medium charge cationic starch (~ 0.03 degree of substitution, DS) to pretreat the NFC rather than a high charge density cationic starch (~ 0.2 DS). In each case, the dewatering was further enhanced by subsequent treatments by cPAM (0.1% on whole furnish solids) and then even more with the final addition of colloidal silica (0.1% and 0.2% levels compared). However, the colloidal silica additions progressively hurt the tensile strength of the paper, especially in the case of the high charge cationic starch and at the higher level of colloidal silica. Though the dewatering performance was favorable, in such cases, the paper strength was not improved compared to paper made without any NFC. The fact that the systems involving cPAM treatment, and especially those involving both cPAM and colloidal silica, tended to reduce the resulting paper’s tensile strength supports a mechanism in which the additives result in the clustering of the NFC, possibly in multiparticle bunches. Evidence suggests that such bunches of clustered NFC particles, which are difficult to redisperse even at levels of hydrodynamic shear present in high-speed paper machine systems, are resistant to full integration into the sheet structure as the paper is being formed.
Journal articles
ABSTRACT: Lignin’s potential as a source of sustainable aromatic compounds is significant, but its utilization is currently limited by its chemical reactivity. Chemical reactivity of lignin depends on the present functional groups, such as hydroxyl, metho
ABSTRACT: Lignin’s potential as a source of sustainable aromatic compounds is significant, but its utilization is currently limited by its chemical reactivity. Chemical reactivity of lignin depends on the present functional groups, such as hydroxyl, methoxy, and carbonyl groups. Therefore, in this study, multivariate analysis-based chemometric models have been developed for rapid determination of aliphatic hydroxyl (Alp-OH) and phenolic hydroxyl (Ph-OH) groups in lignin samples. Two chemometric models, principal component regression (PCR) and partial least squares regression (PLSR), were established with Fourier transform infrared spectroscopy (FTIR) spectral data of 28 lignin samples. Both the models were developed based on raw and pretreated spectroscopic data with Savitky-Golay (S-G) filtering and standard normal variate (SNV) and multiplicative scatter correction (MSC). The predictive performance of the PLSR model is better for predicting Alp-OH (R2 = 0.94%), syringyl-OH (R2 = 0.96%), guaiacyl-OH (R2 = 0.98%), p-hydroxyphenyl (R2 = 0.93%), and total Ph-OH groups (R2 = 0.97%) with the data pretreated by MSC. Finally, the predicted results of these parameters for three new samples for the developed models are found to be very close to the estimated values by NMR.
Journal articles
ABSTRACT: This study investigates the impact of pulp screening on oxygen delignification of high lignin content kraft pulps from spruce wood. An alternative process is proposed: terminating kraft cooking at higher kappa numbers and applying oxygen deligni
ABSTRACT: This study investigates the impact of pulp screening on oxygen delignification of high lignin content kraft pulps from spruce wood. An alternative process is proposed: terminating kraft cooking at higher kappa numbers and applying oxygen delignification directly to unscreened and non-defibrated pulp. The objective is to evaluate whether this non-standard approach can maintain delignification efficiency while improving yield and reducing energy input. The findings demonstrate that screening prior to oxygen delignification is not essential for effective lignin removal or pulp quality. Similar delignification degrees and ISO brightness levels were obtained after oxygen delignification, whether it was performed on screened or unscreened pulps. Notably, the delignification rate in the oxygen stage was the same for the non-standard procedure as for pulp from the standard procedure with the reject fractionremoved prior to the oxygen stage. No significant differences were seen in fiber morphology, brightness level, orbrightness stability. The amount of total fiber charges in pulps not screened before oxygen delignification was slightly higher than in screened pulps.
Journal articles
Exploratory study on how sub-ply fiber orientation affects t
ABSTRACT: The transition to 100% biobased packaging presents considerable challenges, particularly in the development of a petroleum-free barrier. Generally, biobased barriers exhibit lower flexibility compared to traditional barriers, thereby increasing the risk of cracking during the converting process. The present study examines the possibility of optimizing the substrate to reduce cracking in brittle barriers. Five three-ply composites were fabricated using commercial paperboard to enable a composite with different fiber orientation in the individual plies. The different orientations achieved varying mechanical properties, including strain-atbreak and folding resistance, with a ranking that is comparable to a standard multi-ply paperboard. The composites were subjected to creasing at five distinct depths to assess the area percent of barrier cracks across the crease bead. Micro-cracks appeared on the surface before larger coating cracks were registered. As expected, the area percent of barrier cracks increased significantly with greater creasing depths. The orientation of the bulky middle ply showed little difference in the cracking propensity. However, by replacing the stiffer bottom ply with a ply of lower stiffness, the cracking propensity was significantly reduced without a substantial loss in mechanical properties. Hence, these findings indicate that it is possible to reduce the cracks in the barrier by modifying the fiber orientation in the different plies.
Journal articles
Improving barrier performance of coated paper and paperboard
ABSTRACT: Market demand for barrier coated packaging paper and paperboard has been on a steady rise and is forecasted to further increase. As a result, there is a continued interest in improving barrier coating functionalities, which is currently an active area of investigation. In this work, a multi-layer approach was adopted that involved applying a biowax emulsion, latex, or a combination of biowax and latex top coating layer onto the kaolin/latex (20/80, 50/50, 65/35, or 70/30) precoated solid bleached sulfate (SBS) paperboard. Our main objective was to demonstrate the effect of these top coating layers on various barrier properties, especially water vapor transmission rate (WVTR) at high relative humidity (RH) and high temperature (90% RH; 38°C), known as tropical/jungle test conditions. While the top coat with latex and/or biowax showed dramatic improvement in both water resistance (Cobb) and WVTR, the biowax coating increased contact angle significantly compared to the latex top coat. Contact angle increased from about 65° for the latex top coat to as high as 96° for the biowax top coat. Generally, it is much more difficult to improve WVTR at the jungle conditions below 100 g/m2/day, even with the high aspect ratio platy pigment. However, using the coating strategies adopted in this study, we were able to achieve WVTR values notably below 50 g/m2/day at the tropical test conditions, as well as significant improvements in regard to fold crack barrier integrity at high kaolin clay usage.
Journal articles
Prediction of residual calcium carbonate (CaCO3) in the lime
ABSTRACT: In a kraft pulp mill, the rotary lime kiln is responsible for converting calcium carbonate (CaCO3) into calcium oxide (CaO) to be reused in the causticizing plant. An important parameter of the calcination efficiency and the product quality is the amount of CaCO3 not converted to CaO, commonly defined as residual carbonate. This parameter is usually determined through laboratory analysis, which introduces delays in process control and limits the ability to make timely operational adjustments. This work presents a predictive model that functions as a soft sensor for the residual carbonate in a lime kiln of a Brazilian kraft pulp mill. This model was able to estimate residual CaCO3 every 30 min using routinely measured online process variables, which is a considerable reduction from the 6-h average laboratory measurement. The correlation coefficient (r) between the model predictions and the mill values was 0.83, with a mean absolute error (MAE) of 0.33%. Considering the effect of the residence time throughout the lime kiln proved to be decisive in obtaining a satisfactory prediction result. After model validation, a variable importance analysis showed that the carbon monoxide (CO) concentration in the stack flue gas (in ppm), secondary air temperature (in oC), and fan speed (in %) were the most influential variables in predicting the residual carbonate content. Combined with commonly used operation expertise, this subset of variables can serve as additional information to achieve smoother lime kiln operation.
Journal articles
Black liquor spray properties in-furnace conditions for swirl cone nozzles, TAPPI Journal July 2026
ABSTRACT: Recovery boiler furnace operation is controlled for high chemical recovery, high steam production, and low emissions. Good control allows long runs with minimum cleaning without expensive shutdowns. An essential variable affecting boiler operation is black liquor spraying into the furnace. Poorly controlled black liquor spraying causes difficulties, e.g., in chemical recovery, fouling of heat transfer surfaces, and decreased energy production. A challenging measurement strategy with three different swirl cone nozzles . types A, C, and T . was carried out at a mill in the United States. Black liquor spray properties were measured under in-furnace conditions for flow rates of 2.0 L/s to 3.0 L/s. Three spraying temperatures of 119™‹C, 122™‹C, and 126™‹C, which were 2™‹C, 5™‹C, and 9™‹C above the boiling point (ƒ¢Te), were tested. These flow rates and temperatures are typical for industrial nozzle sizes with exit orifice sizes of 17 mm and 22 mm. An imaging method to measure droplet size in a highly challenging furnace environment was developed. Droplet volume median diameter (Dv50) for nozzles A, C, and T varied between 7 mm to 4 mm, 7 mm to 5 mm, and 8 mm to 6 mm, depending on the flow rate and temperature. The high number of droplets detected by the analysis program enabled data fitting into statistical correlations. The size and width parameters for the Rosin™]Rammer droplet size distribution function could be defined. The droplet size distribution was found to be surprisingly wide, probably because of swollen droplets. Spray velocity was measured in two locations, 5 cm from the nozzle and 1.8 m from the nozzle. Near the nozzle, the average velocity increased from 7.3 m/s to 13 m/s when the flow rate was increased from 2 L/s to 3 L/s. Increase of black liquor temperature increased spray velocity in most of the cases. At the distance of 1.8 m from the nozzle, average spray velocities varied between 4.0 m/s to 11 m/s, depending on nozzle geometry, flow rate, and temperature. The opening angles of the spray for nozzles A and C varied between 57™‹ to 78™‹. The opening angle of nozzle T with flow guide varied between 48™‹ to 56™‹. The highest penetration of the spray was estimated for nozzle T because of the narrow spray and large droplets.
Journal articles
Non-process elements in the lime cycle: New findings regarding NPE distribution and lime mud filterability, TAPPI Journal July 2026
ABSTRACT: Proper functioning of the recausticizing cycle is crucial for securing a stable white liquor supply for a pulp mill. Common runnability problems in the modern lime cycle, such as low filterability and poor dewatering of lime mud, high dead load, or ring formation in the lime kiln, are often caused by accumulation of non-process elements (NPEs). This project attempted to verify the traditional rules of thumb regarding the chemical behavior of NPEs: magnesium (Mg), aluminum (Al), silicon (Si), phosphorus (P), zinc (Zn), manganese (Mn), iron (Fe), copper (Cu), barium (Ba), cadmium (Cd), and lead (Pb) in the causticizing reaction, and to investigate the reasons behind poor lime mud filterability. First, a standardized method for measuring filterability of lime mud was developed. Next, a series of recausticizing experiments, followed by immediate filtration trials, was conducted using mill green liquors, laboratory-made synthetic green liquor, reburned lime/makeup mix, and extra NPE additions. It was found that sodium (Na), potassium (K), and sulfur (S) followed the liquid phase, as expected, while Mg, P, and Ba, but also Pb, Cu, and Cd, showed low solubility and accumulated in the lime mud. The Si and Al accumulated in the lime mud even though the soluble content in liquor was high, while the behavior of Mn, Fe, and Zn was more complex. Based on these results, tentative solubility limits for NPEs were suggested as a first estimate for the maximum possible concentrations of NPEs in mill white liquor. The causticization-filtration experiments revealed that overliming and high content of Mg in green liquor clearly led to lower filterability, but our addition of Si did not have such an effect. As differences in particle size and size distribution have a certain impact on the filtration resistance, the lime mud sedimentation behavior, combined with other characterization methods, might be used as an indication for the filterability. Finally, a list of recommendations for pulp mills was formulated that starts with establishing a comprehensive standard for a lime mud with good filterability. This standard can be used as a benchmark for comparison any time a lime cycle runnability problem is identified.