Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Production of antimicrobial paper using nanosilver, nanocellulose, and chitosan from a coronavirus perspective, TAPPI Journal July 2021
ABSTRACT: The pulp and paper industry has an opportunity to play a vital role in breaking the spread of the COVID-19 pandemic through production that supports widespread use of antimicrobial paper. This paper provides a brief review of paper and paper-related industries, such as those producing relevant additives, and R&D organizations that are actively engaged in developing antimicrobial papers. The focus here is on the potential of three nano-additives for use in production of antimicrobial papers that combat coronavirus: nanosilver, nanocellulose, and chitosan. Various recent developments in relevant areas and concepts underlining the fight against coronavirus are also covered, as are related terms and concepts.
Journal articles
Magazine articles
Addressing production bottlenecks and brownstock washer optimization via a membrane concentration system, TAPPI Journal July 2021
ABSTRACT: Advancements in membrane systems indicate that they will soon be robust enough to concentrate weak black liquor. To date, the economic impact of membrane systems on brownstock washing in kraft mills has not been studied and is necessary to understand the viability of these emerging systems and their best utilization.This study investigated the savings that a membrane system can generate related to brownstock washing. We found that evaporation costs are the primary barrier for mills seeking to increase wash water usage. Without these additional evaporation costs, we showed that our hypothetical 1000 tons/day bleached and brown pulp mills can achieve annual savings of over $1.0 MM when operating at higher dilution factors and fixed pulp production rate. We then investigated the impact of increasing pulp production on mills limited by their equipment. In washer-limited mill examples, we calculated that membrane systems can reduce the annual operating cost for a 7% production increase by 91%. Similarly, in evaporator-limited mill examples, membrane systems can reduce the annual operating cost for a 7% production increase by 86%. These results indicated that membrane systems make a production increase significantly more feasible for these equipment-limited mills.
Journal articles
Magazine articles
Rethinking the paper cup — beginning with extrusion process optimizationfor compostability and recyc
ABSTRACT: More than 50 billion disposable paper cups used for cold and hot beverages are sold within the United States each year. Most of the cups are coated with a thin layer of plastic — low density polyethylene (LDPE) — to prevent leaking and staining. While the paper in these cups is both recyclable and compostable, the LDPE coat-ing is neither. In recycling a paper cup, the paper is separated from the plastic lining. The paper is sent to be recycled and the plastic lining is typically sent to landfill. In an industrial composting environment, the paper and lining can be composted together if the lining is made from compostable materials. Coating paper cups with a compostable performance material uniquely allows for used cups to be processed by either recycling or composting, thus creating multiple pathways for these products to flow through a circular economy.A segment of the paper converting industry frequently uses an extrusion grade of polylactic acid (PLA) for zero-waste venues and for municipalities with ordinances for local composting and food service items. The results among these early adopters reveal process inefficiencies that elevate manufacturing costs while increasing scrap and generally lowering output when using PLA for extrusion coating. NatureWorks and Sung An Machinery (SAM) North America researched the extrusion coating process utilizing the incumbent polymer (LDPE) and PLA. The trademarked Ingeo 1102 is a new, compostable, and bio-based PLA grade that is specifically designed for the extrusion coating process. The research team identified the optimum process parameters for new, dedicated PLA extrusion coating lines. The team also identified changes to existing LDPE extrusion lines that processors can make today to improve output.The key finding is that LDPE and PLA are significantly different polymers and that processing them on the same equipment without modification of systems and/or setpoints can be the root cause of inefficiencies. These polymers each have unique processing requirements with inverse responses. Fine tuning existing systems may improve over-all output for the biopolymer without capital investment, and this study showed an increase in line speed of 130% by making these adjustments. However, the researchers found that highest productivity can be achieved by specifying new systems for PLA. A line speed increase to more than 180% and a reduction in coat weight to 8.6 µm (10.6 g/m2 or 6.5 lb/3000 ft2) was achieved in this study. These results show that Ingeo 1102 could be used as a paper coating beyond cups.
Journal articles
Aging and degradation of oil and grease barrier papers coate
ABSTRACT: The long-term performance and stability of bio-based barrier coatings are critical for sustainable packaging. In this study, the aging and degradation of a biobased starch•wax emulsion coating were examined on two different base papers. Coated samples were stored for 8 months at 23°C and 50% relative humidity (RH) in their original reels to minimize external exposure and isolate internal aging effects. Multiple aging intervals were analyzed using advanced methods to assess both chemical composition and physical structure. The water vapor transmission rate (WVTR) of both coated papers increased during the first 15 days, but after eight months, the WVTR dropped below the initial values. Fourier transform infrared (FTIR) results supported these trends by showing a marked rise in the polarity index (PI), occurring predominantly within the first 15 days. The overall observations, including increases in the PI, carbonyl index (CI), and absolute absorbance in the hydroxyl region, confirm that both hydrolysis and oxidation occurred during aging. The gradual increase in the aliphatic C•H stretching peaks indicated that wax components moved toward the surface over time. The non-uniform surface enrichment of oleophilic wax following migration contributed to the decline in Kit rating upon aging by facilitating oil and grease wetting and penetration. At the same time, increased wax concentration at the surface helped improve the water vapor barrier performance during long-term aging. Scanning electron microscopy (SEM) imaging revealed distinct surface cracks over time on the starch-wax emulsion coated papers. The FTIR analysis supported these observations through an increase in the conformational disorder index (CDI) with aging. Physical changes were further reflected in the barrier performance, as the heptane vapor transmission rate (HVTR) increased significantly for both coated papers over the 8-month period.
Journal articles
A novel dimensionless index for optimizing the thermo-hydrau
ABSTRACT: The comprehensive performance of steam condensation in horizontal rotating channels, which involves a trade-off between heat transfer enhancement and flow resistance, lacks a unified evaluation criterion. This deficiency is particularly critical for applications such as a multi-channel cylinder dryer (MCD) in paper machines, where rotational operation enhances drying efficiency. To address this gap, this study introduces a novel dimensionless index, W/Eu, defined as the ratio of the dimensionless heat transfer coefficient (W) to the dimensionless pressure drop (Eu), thereby taking into account both heat transfer and flow resistance characteristics comprehensively. A functional relationship for this index was established with respect to channel spacing (Wr) and steam mass flux (G), followed by a theoretical optimization analysis. The analysis reveals that W/Eu decreases monotonically as Wr increases and increases monotonically as G increases, ultimately diverging as G ™¨ ™‡. Consequently, for any given operational range, the theoretical maximum performance is achieved at the boundary condition of minimum channel spacing (Wr ™¨ 0) and maximum allowable mass flux (G = Gmax). This work provides a clear theoretical directive for the design and optimization of high-efficiency rotating heat exchanger systems, offering valuable insights for enhancing the drying performance of microchannel dryers in paper machines and similar rotary thermal systems.
Journal articles
Magazine articles
Production and characterization of furanic bio-oil from Kawayan kiling (Bambusa vulgaris Schrad ex. Wendl) using molten citric acid in an open system, TAPPI Journal August 2024
ABSTRACT: The burning of fossil fuels poses many threats to the environment. These predicaments have led to a continuous search for alternative sources and production of energy, and biomass is considered the most abundant renewable energy source. In this study, the potential to produce furanic bio-oil from the cellulose of Bambusa vulgaris was explored. The proximate chemical analysis of bamboo was determined using TAPPI Standards. Cellulose was isolated through dewaxing, delignification, and alkaline treatments. The furanic bio-oil was produced by mixing cellulose and citric acid in a solvent-free environment. The effects of the digestion time (120 min, 180 min, and 240 min) on the yield and characteristics were determined. The chemical compositions were determined using Fourier transform infrared (FTIR) spectroscopy and gas chromatography-mass spectrometry (GCMS). B. vulgaris has the following chemical composition: alpha-cellulose (57.42 ± 0.40), holocellulose (78.84 ± 0.52), lig-nin (28.85 ± 0.17), hot water extractives (3.99 ± 0.08), organic extractives (0.77 ± 0.04), ash (4.67 ± 0.02), and moisture (12.98 ± 0.22). The bio-oil yield was affected by the digestion time. The highest yield was obtained at 180 min, followed by 120 min, and 240 min with 88.59%, 59.28%, and 49.96%, respectively. The peaks in the FTIR spectra corresponded to the compounds determined by the GCMS analysis. The dominant chemicals were furans (29.19%), ketones (26.31%), and carboxylic acids (19.26%). The bio-oil obtained at 180-min digestion time has the following properties: sulfur content (0.032 wt%), kinematic viscosity (1.03 mm2/s), specific gravity (0.925), copper corrosion test (No. 1a), pH (2.753), and water content (not detected). Overall, the obtained values from the properties and chemical characterization can be the basis for investigating its performance for biofuel production and utilization. This study is aligned with the Bamboo Industry’s Strategic Science and Technology Plan for the Philippines to develop other value-added products from bamboo and to achieve Sustainable Development Goal 7 (SDG 7) as determined by the United Nations.
Journal articles
Beyond the machine: Decoding process water microbes behind odor in papermaking, TAPPI Journal February 2026
ABSTRACT: Paper manufacturing processes create an ecosystem conducive to microbial growth, characterized by abundant water, nutrients, and optimal temperatures, fostering diverse microbial habitats. With the increased use of recycled fibers and greater water system closure, the industry now faces amplified microbiological challenges, particularly odor generation. These odor problems have raised community concerns, as shown by resident com-plaints, and have led to significant economic impacts, including costly lawsuits against major paper manufacturers. Based on earlier studies showing that microbes in papermaking systems can generate odor-causing volatile com-pounds, this study is guided by the hypothesis that recycle paper mill process water harbors odor-causing microbial communities and thus represents a primary source of malodor. To test this hypothesis, process water samples from commercial recycle paper mills were analyzed using high-throughput Illumina sequencing to characterize microbial communities in one complete analysis. The study results revealed fifteen major microbial populations, dominated mainly by the genus Pseudomonas. The identified microbes were further linked to prior literature to determine their functional roles in odor generation, including the production of haloanisoles (2-monochloroanisole, 2,4-dichloroanisole, 2,3,6-trichloroanisole, 2,4,6-tri-bromoanisole), geosmin, 2-methylisoborneol, and volatile organic sulfur compounds such as dimethyl polysulfides, hydrogen sulfide, and methylmercaptan. This study introduces a microbiological community-profiling approach that enables papermakers to assess whether process water represents a potential source of malodor. Earlier studies have not examined microbial com-munities in recycle paper mill process water specifically from the perspective of identifying malodor sources, nor have they integrated such findings with an extensive literature-based assessment. The findings of this study advance both science and practice by offering a method that can serve as an early diagnostic tool for papermakers, supporting effective future odor management and deepening understanding of microbial ecology in paper mill environments.
Journal articles
Optimization of optical coverage of board surfaces with assessment of light scattering and absorption using mineral as a coating component, TAPPI Journal June 2026
ABSTRACT: One of the primary functions of mineral inclusion into paper or paperboard is to improve the optical performance of the substrate. A coating may be applied to a sheet in order to cover a dark base, to improve the sheet opacity, to give the correct smoothness and gloss, or to give a suitable surface on which to print. The brightness of a pigment has long been used as a guide for pigment choice in paper and board. However, the measured paper brightness is a function of color and light absorption (K) of the coating and base and the light scattering (S) within the sheet resulting from interfaces with different refractive index. The optical performance can be quantified by measuring the S&K coefficients as described by the Kubelka-Munk model/theory in a filled or coated paper sheet. In coating, this is often assessed as a function of coat weight, and the corresponding physical sheet properties are assessed at the same time; for example, the correct gloss, smoothness, point-to-point uniformity, and printability. The optical performance in the sheet is often not directly related to the pigment brightness, but is largely a function of the particle packing within the sheet and coating layer. In the first and second main sections of this work, respectively, we show how S&K calculations from the Kubelka- Munk equations can be used in coated sheets to determine the optical performance and how this can be used as a predictive tool for the final sheet performance. This is presented for base sheets with different starting brightness. The third section of this work focuses on how mineral combinations in coatings can be used to improve the light scattering and consequently the optical performance of the board. We include theoretical considerations and then finally share a case study for improvement on the optical properties of recycled board.
Journal articles
Magazine articles
Rethinking the paper cup — beginning with extrusion process optimization for compostability and recyclability, TAPPI Journal June 2021
ABSTRACT: More than 50 billion disposable paper cups used for cold and hot beverages are sold within the United States each year. Most of the cups are coated with a thin layer of plastic — low density polyethylene (LDPE) — to prevent leaking and staining. While the paper in these cups is both recyclable and compostable, the LDPE coat-ing is neither. In recycling a paper cup, the paper is separated from the plastic lining. The paper is sent to be recycled and the plastic lining is typically sent to landfill. In an industrial composting environment, the paper and lining can be composted together if the lining is made from compostable materials. Coating paper cups with a compostable performance material uniquely allows for used cups to be processed by either recycling or composting, thus creating multiple pathways for these products to flow through a circular economy.A segment of the paper converting industry frequently uses an extrusion grade of polylactic acid (PLA) for zero-waste venues and for municipalities with ordinances for local composting and food service items. The results among these early adopters reveal process inefficiencies that elevate manufacturing costs while increasing scrap and generally lowering output when using PLA for extrusion coating. NatureWorks and Sung An Machinery (SAM) North America researched the extrusion coating process utilizing the incumbent polymer (LDPE) and PLA. The trademarked Ingeo 1102 is a new, compostable, and bio-based PLA grade that is specifically designed for the extrusion coating process. The research team identified the optimum process parameters for new, dedicated PLA extrusion coating lines. The team also identified changes to existing LDPE extrusion lines that processors can make today to improve output.The key finding is that LDPE and PLA are significantly different polymers and that processing them on the same equipment without modification of systems and/or setpoints can be the root cause of inefficiencies. These polymers each have unique processing requirements with inverse responses. Fine tuning existing systems may improve over-all output for the biopolymer without capital investment, and this study showed an increase in line speed of 130% by making these adjustments. However, the researchers found that highest productivity can be achieved by specifying new systems for PLA. A line speed increase to more than 180% and a reduction in coat weight to 8.6 µm (10.6 g/m2 or 6.5 lb/3000 ft2) was achieved in this study. These results show that Ingeo 1102 could be used as a paper coating beyond cups.
Journal articles
Magazine articles
Understanding the risks and rewards of using 50% vs. 10% strength peroxide in pulp bleach plants, TAPPI Journal November 2018
Authors: Alan W. Rudie and Peter W. Hart | ABSTRACT: The use of 50% concentration and 10% concentration hydrogen peroxide were evaluated for chemical and mechanical pulp bleach plants at storage and at point of use. Several dangerous occurrences have been documented when the supply of 50% peroxide going into the pulping process was not stopped during a process failure. Startup conditions and leaking block valves during maintenance outages have also contributed to explosions. Although hazardous events have occurred, 50% peroxide can be stored safely with proper precautions and engineering controls. For point of use in a chemical bleach plant, it is recommended to dilute the peroxide to 10% prior to application, because risk does not outweigh the benefit. For point of use in a mechanical bleach plant, it is recommended to use 50% peroxide going into a bleach liquor mixing system that includes the other chemicals used to maintain the brightening reaction rate. When 50% peroxide is used, it is critical that proper engineering controls are used to mitigate any risks.