Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Effects of carboxymethyl starch as a papermaking additive, TAPPI Journal February 2024
ABSTRACT: Carboxymethyl starch (CMS) is a bio-based, anionic polymer that has potential as part of a dry-strength additive program for papermaking. Due to its negative charge, its effects can be expected to depend on its interactions with various cationic agents. In this work, the effects of CMS were observed following its sequential addition after one of three selected cationic strength agents at different dosage levels. In selected tests, the furnish was pretreated at the 1% level by a dispersant, sodium polyacrylate, which might represent a high level of anionic contaminants in a paper mill system. Laboratory tests were conducted to show the effects on dewatering, fine-particle retention, and flocculation. These tests were supplemented with measurements of charge demand, zeta potential, and handsheet properties. Sequential addition of cationic glyoxylated acrylamide copolymers (gPAM) and CMS were found to strongly promote dewatering. Two gPAM products and a poly(vinylamine) product in sequential addition with CMS were very effective for promoting fine-particle retention. These same sequential treatments of the stock contributed to moderate fiber flocculation, though severe flocculation was caused by further treatment of the furnish with colloidal silica. Handsheet strength results were mixed. In the default recycled copy paper furnish, the average breaking length for the sheets made with cationic additives followed by CMS was not greatly different from the blank condition. Superior strength resulted when the default furnish was treated with a dispersant alone. When the dispersant-contaminated furnish was treated with the same combinations of cationic additives and CMS, the strength returned to the baseline achieved in the absence of the dispersant. The results were discussed in terms of the charged character of the different additives and their interactions not only with the fiber surfaces but also with each other.
Journal articles
Magazine articles
Amphoteric dry strength chemistry approach to deal with low-quality fiber and difficult wet-end chemistry conditions in the Asian and North American markets, TAPPI Journal January 2024
ABSTRACT: With Japan’s high recycling rates and low access to fresh fiber sources, reaching strength targets in manufacturing packaging materials is a challenge. Declining quality of recycled fiber and minimal freshwater con-sumption results in difficult wet-end chemistry conditions in terms of high conductivity and elevated levels of dissolved and colloidal substances (DCS). These trends are somewhat typical of other Asian regions. Due to global trade, Asian packaging materials have become a part of the North American (NA) raw material pool. The gradual closing of mill water circuits for fresh water and energy savings results in more difficult wet-end chemistry conditions experienced in North America. China’s ban on the import of mixed paper and the consequent ban on all waste-paper imports triggered a significant price drop in recycled raw material, resulting in plans for increased manufacturing capacity in North America. Between increased demand, decreasing fiber quality, and movement towards more closed white water systems associated with packaging grade paperboard (even a virgin fiber mill uses a fair amount of recycled fiber), new methods to overcome strength reduction in raw materials must be proactively considered for North America. Reviewing the strategies currently used in the Asian industry regarding strength development is an excellent starting place for NA producers. A clear difference between Asian and NA wet-end chemistry is the dominant position of amphoteric dry strength agents. This paper reviews the fundamentals of dry strength development that explain the trend towards the increased application of amphoteric dry strength technology for poor-quality fiber and highly contaminated water circuits in Asian markets. This paper discusses the development and application perfor-mance of the novel 4th generation amphoteric polyacrylamide (AmPAM) dry strength technology, based on selected laboratory and mill case studies.
Journal articles
Magazine articles
Modeling the dynamics of evaporator wash cycles, TAPPI Journal July 2024
ABSTRACT: Kraft pulping is a process that utilizes white liquor, composed of sodium sulfide (Na2S) and sodium hydroxide (NaOH), for wood delignification and pulp production. This process involves washing the dissolved organics and spent chemicals from the pulp, resulting in the generation of black liquor. Prior to its use as fuel in the recovery boiler, the black liquor is concentrated in multiple-effect evaporators. During the evaporation process, the inorganic salts present in the liquor become supersaturated and undergo crystallization. Fluctuations in sodium, carbonate, sulfate, and oxalate can give rise to severe sodium salt scaling events, which significantly impact the thermal efficiency of the evaporators, and ultimately, pulp production. Dynamic modeling provides insights into fluctuations in liquor chemistry in the evaporators. The primary objective of this study was to employ dynamic modeling to evaluate the effects of wash liquor recovery from evaporator wash cycles. The dynamics associated with wash cycles encompass variations in the concentrations of salts and solids in the recovered wash liquor, changes in the flow rate of wash liquor recovery, and fluctuations in liquor volume within the liquor tanks. The dynamic model was developed using Matlab Simulink and applied to the evaporation plant of a pulp mill in South America. By utilizing one month of mill process data, the model enabled the evaluation of fluctuations in liquor chemistry due to evaporator wash cycles. The developed model has demonstrated the potential to estimate the concentration of key ions responsible for scaling and to contribute to enhancements in evaporator washing strategies.
Journal articles
Effects of biopolymer coatings on paper permeability and capillarity for paper-based rapid diagnostic test devices, TAPPI Journal September 2025
ABSTRACT: Rapid diagnostic test (RDT) devices are widely used for diagnostics due to their affordability, portability, and user-friendliness. However, conventional assays typically rely on nitrocellulose membranes and plastic casings. These materials raise environmental concerns due to their non-renewable nature, energy-intensive production methods, and poor biodegradability. This study explores the development of fully bio-based RDT substrates using a sustainable alternative: softwoodderived microfibrillated cellulose (MFC), cellulose nanocrystals (CNC), and chitosan as surface modifiers to improve paper properties and enhance RDT sustainability. Cotton filter paper substrates were coated with different biopolymer formulations using a manual blade coater: bleached MFC (BMFC), lignin-containing MFC (LMFC), BMFC combined with CNC, LMFC combined with CNC, and chitosan. Evaluation of the most relevant physical properties concerning RDT performance was conducted, including wetting, water retention value, air permeability, capillary flow rate, and surface morphology. Results showed that biopolymer- based coatings can effectively modify surface properties by reducing pore size and tuning hydrophilicity, while maintaining the renewable and bio-based characteristics of the substrate. The LMFC-coated paper exhibited the best overall performance among all formulations, reducing flow time by 50% (3.00 mm/s vs. 1.5 mm/s) compared to the uncoated paper, yet preserving high water retention. The BMFC+CNC coating also significantly improved flow rate, showing a 36.7% reduction (2.37 mm/s vs. 1.5 mm/s), and enhanced porosity uniformity. In contrast, the flow rate of chitosan-coated paper decreased by over 5,000% (0.027 mm/s), reflecting its strong barrier properties and hydrophobic surface (highest contact angle: 91.4°). These findings suggest that MFC-based coatings are promising ecofriendly alternatives to nitrocellulose, offering optimized capillary transport and structural adaptability. This paves the way for the development of sustainable, high-performance, rapid diagnostic tests.
Journal articles
Water and grease resistance of paperboard coated with long chain cellulose fatty acid esters using electrostatic powder coating, TAPPI Journal April 2026
ABSTRACT: Fiber-based materials used for foodservice, takeaway, and other packaging applications must typically provide water and grease resistance. Simultaneously, there is growing interest towards bio-based and renewable barrier coatings. In this study we applied thermoplastic long chain fatty acid cellulose esters onto paperboard using electrostatic powder coating to create barrier properties of interest. Electrostatic powder coating provides a water-free process to tackle moisture-induced quality issues and to provide an even coating layer. Cellulose octanoate and palmitate esters were produced in pilot scale. These were ground into fine particles using liquid nitrogen and applied onto paperboard sheets using an electrostatic powder gun. The loosely packed coatings were fixed and fused onto the paperboard by hot pressing. We characterized the coated sheets for coating thickness, contact angles with water, water absorption, grease resistance (KIT), and olive oil barrier. Two commercial polyethylene powders were used as references. Our results indicated that the long chain cellulose fatty acid ester coatings were thermoplastic and hydrophobic with contact angles above 100°. Water absorption was similar to the reference coatings. While grease resistance was lower than with the references, the cellulose ester coatings slowed down diffusion of olive oil through the paperboard. Cellulose octanoate ester with a lower melt viscosity already provided smooth coatings after the initial hot pressing step, while in most cases, the second post hot pressing step further improved the barrier properties.
Journal articles
Comparative evaluation of conical and double disk refiners: Effects of operating mode, refining intensity, and device geometry on energy consumption and paper properties, TAPPI Journal August 2026
ABSTRACT: This study investigates the effects of refiner operating mode and refining intensity adjusted via pulp flow rate, applied power, and refiner speed on the refining characteristics of high-yield southern softwood. We compared Valmet’s OptiFiner PRO (conical) and DD6700 (double disk) refiners under matched specific edge load (SEL) conditions. Batch and one-pass modes were evaluated for their impact on energy efficiency and physical paper properties. The results showed that while SEL provides a useful baseline, it does not fully account for differences in refiner geometry, particularly angular parameters. With the chosen plate sets, C-factor analysis revealed that the OptiFiner PRO delivers a lower number of fiber impacts at a higher intensity per impact compared to DD6700 at similar SEL, influencing fiber length, short-span compression test (STFI) index, and tear strength development. These findings offer actionable insights for mills seeking to optimize refining efficiency and cost. In summary, conical refiners may provide advantages in compression strength at mid-range energies, while double disk refiners maintain higher tear strength at elevated energies due to better fiber length preservation.
Journal articles
Simplified modeling of a complete rotary lime kiln at a pulp mill, TAPPI Journal February 2026
ABSTRACT: Rotary lime kilns are essential and complex components in pulp mills using the kraft process. They are primarily used to produce lime (CaO), which is then employed to make white liquor, the reagent used to separate wood fibers. To understand and improve the performance of the kiln, modeling its behavior is essential. However, the kiln operates through a complex combination of thermal and chemical phenomena. That is why a simplified approach was used to tackle this challenge. A zero/one-dimensional steady-state analysis was performed based on first principles to simplify the modeling process and reduce the need for experimental data. Additional assumptions, such as steady-state operation and the absence of a refractory lining, were introduced to further simplify the model so that it can be used for daily analysis. Moreover, the auxiliary equipment of the plant, such as the intercooler and preheat cyclone, is also modeled. The final model was validated using data from the literature and a two-month analysis of experimental measure-ments from the Burgo Ardennes lime kiln in Virton, Belgium. It shows good agreement with the available data, with a 6% deviation for the adiabatic flame temperature and a 17% average error in predicting the kiln shell outside temperature. For the fuel and lime flow rate predictions, also validated over the same two-month period, the errors were -6.6% and 0.6%, respectively.
Journal articles
Full-scale operation of a membrane-based black liquor concentrator, TAPPI Journal January 2026
ABSTRACT: For years, black liquor concentration by reverse osmosis has been an aspiration for reducing mill energy consumption and costs. Building on a 2023 report of an 81% reduction in the energy intensity for concentrating black liquor using its membrane platform at the pilot scale, this paper reports on the fabrication, installation, startup, and operation of the world’s first full-scale membrane-based black liquor concentration system at the International Paper Grande Prairie mill in Canada. The majority of the membrane modules in this system have reliably exceeded permeability expectations by more than 50%. In addition to strong membrane performance, the system has been a significant source of learnings for material specifications and system design. Incorporating these learnings and comparing to typical multiple effect evaporators, the system demonstrates a 43% reduction in capital cost for the same capacity, a 30% reduction in the lifetime cost of removing water from black liquor, and an 86% reduction in energy use. The impact on washer optimization was also considered, and net energy and chemical costs were reduced by US$3.8 and US$6.8/a.d. metric ton for a typical brown and bleach mill, respectively, when incorporating this technology. Completed in less than 12 months, the facility has demonstrated successful black liquor concentration at the 500 gpm scale with monthly uptime as high as 96%.
Journal articles
Energy and emission implications of optimized white liquor causticity, TAPPI Journal January 2026
ABSTRACT: Optimizing the causticizing plant offers significant opportunities for energy and emissions savings in kraft mills by minimizing the chemical and water deadload introduced into the recovery cycle via white liquor. Modern control strategies utilize both feedforward and feedback loops to manage causticity, enabling more aggressive targets closer to equilibrium levels. This paper evaluates the benefits of optimizing white liquor chemistry through a detailed CADSIM Plus simulation model, replicating the chemistry of a Canadian bleached kraft mill that adopted an automated causticizing control system. The control system increased causticity from 77.0% to 82.3% at a fixed total titratable alkali (TTA) of 126.5 grams of sodium dioxide per liter (gNa2O/L). Modeling this chemistry change indicated a 1.5 metric tons per hour (t/hr) reduction in evaporator steam demand and a 2.8% increase in black liquor higher heating value. Consequently, the improved heating value resulted in a 1.5% rise in recovery boiler steam production and a 5.3% reduction in biomass energy consumption in power boilers, leading to a 4.8% decrease in biogenic carbon dioxide (CO2) emissions. Additionally, reducing the inorganic and water deadload throughout the recovery cycle may support higher as-fired dry solids targets, enhancing recovery boiler energy efficiency by lowering the water evaporation requirement during black liquor combustion. However, implementing a causticizing control system requires careful assessment of potential lime kiln bottlenecks, as increased causticity demands may affect kiln operations depending on broader mill conditions. Overall, an automated causticizing control system enhances process efficiency, reduces energy consumption and emissions, and positions kraft mills for improved productivity and longterm sustainability.
Journal articles
Controlling sulfidity by recycling sulfur in CNCG, TAPPI Journal July 2026
ABSTRACT: Pulp and paper mills have faced a major dilemma. On one hand, mills should not dispose of the side streams by mixing them with effluent water. On the other hand, there has been no other way to dispose of excess sulfur than getting rid of recovery boiler electrostatic precipitator (ESP) ash and buying sodium hydroxide to replace lost sodium. A new, yet old, process has been introduced to alleviate the problem. An alternative is the onsite production of sulfuric acid (H2SO4) to significantly reduce, or to even eliminate, the need for recovery boiler fly ash dumping. A sulfuric acid plant produces concentrated commercial quality H2SO4 from concentrated non-condensable gases (CNCGs). Up to 99.9% of the sulfur in CNCGs can be converted into concentrated sulfuric acid with this wet-gas sulfuric acid (WSA) process. There are already references on pulp mills highlighting that the process is straightforward to use. Mills can increase the amount of sulfur in CNCGs by controlling the heavy back liquor storage time and temperature. This opens up a new way to control the mill sulfidity by recycling sulfur. The effect of recycling sulfur is highlighted with reference mills. Due to integrated paper production, the Northern Mill is a large energy consumer, producing mostly softwood-based end products. The Eucalyptus Mill is a large standalone hardwood (eucalyptus) pulp mill where electricity is produced substantially in excess of its own use. As a sample case, lignin production with and without sulfur recycling is presented.