Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Collections
Journal articles
Magazine articles
Effects of rings on flow and temperature in lime kilns, TAPPI Journal June 2022
ABSTRACT: A steady state, two-dimensional (2D) axisymmetric model has been developed to help understand how rings form and grow in a typical lime kiln. Rings of varying length, thickness, and geometry at the front and back faces were modeled to study the effects on flue gas flow and temperature. The results show that ring growth causes the gas velocity to increase and insulates the adjacent refractory, resulting in a lower kiln shell temperature. The results also reveal the formation of recirculation zones immediately down-stream of the rings, as well as temperature deviations upstream and downstream of the rings that might promote recarbonation and further ring growth. The model was applied to a kiln from a kraft mill with front-end and mid-kiln rings and good agreement was obtained between the measured and predicted kiln shell temperatures, providing confidence in the modeling.
Journal articles
Magazine articles
Water chemistry challenges in pulping and papermaking • fundamentals and practical insights: Part 1: Water chemistry fundamentals and pH, TAPPI Journal June 2022
ABSTRACT: Water is an essential component of the papermaking process. Nevertheless, papermakers often overlook its importance compared to fibers and chemical additives. A better understanding of water properties and chemical interactions associated with water at the wet end leads to a sound foundation for high-quality paper production and smooth operation. Not all fresh water and process water is the same. Fresh water varies from mill to mill, primarily due to the location and availability of water sources. Some industrial trends, such as enhancing water conservation and production yield, gradually shift process water quality over time. The current work serves as a primer on water and water chemistry fundamentals to help the papermaker prepare for the future challenges of increased contamination of process water associated with reduced fresh water usage. This paper focuses on basic water chemistry definitions and discusses the impact of pH on wet-end operation. It is clear that pH is a fundamental factor that directly affects the process and impacts other factors relevant to the papermaking process. It is crucial to understand what pH represents, how it is measured, how to select the proper pH and carefully control it, and how to closely maintain the process at target setpoints. Understanding the sensitivity of operation to pH change will lead to an appropriate focus on these issues. In addition to basic theory, we also review onsite experience and practical mill cases. It is imperative to stress that, although critical, pH is not the only chemical parameter impacting papermaking operations. Other factors, such as ionic concentration measured by conductivity, surface, soluble charge, and hardness, are critical and will be discussed in Part II of this series. As pH is a primary and independent factor that impacts various forms of charge and conductivity, the authors decided to start the current series of papers by discussing pH.
Journal articles
Magazine articles
Rewet suppression through press felt engineering, TAPPI Journal June 2022
ABSTRACT: Due to the immense energy and associated financial cost of drying paper, achieving a drier web entering the dryers is a key objective in paper manufacture. One major research thrust has been finding a way to increase press solids by mitigating or eliminating rewet in the press section. For decades, solutions to this problem have remained elusive. In this work, we develop a novel approach that significantly reduces rewet by rupturing the liquid channels between felt and web. We illustrate the effects that altering the mechanical and surface properties of the press felt matrix have on the stability of these liquid channels. In a laboratory-scale platen press, a 40% reduction in the residual water of 120 g/m2 southern bleached softwood kraft (SBSK) pulp handsheets after pressing was observed, corresponding to an increase in press solids from 48% to 61%. For reference, pressing under identical conditions with paper blotters, in which minimal rewet is presumed to occur, resulted in 64% solids. Furthermore, we observed enhanced dewatering across a range of basis weights, applied pressures, and felt types. In addition to measuring the solids content of pressed sheets, we capture and analyze video evidence of the mechanisms at play in our improved dewatering technology.
Journal articles
Magazine articles
The Influence of the Fine Structure of Cellulose on the Action of Cellulases, TAPPI Journal June 2022
ABSTRACT: In the hydrolysis of cellulose with enzymes of Aspergillus niger at 47°C., it shown that a great decrease in the rate occurred in the late stage of the reaction, usually with considerable cellulose still reamaining undissolved.
Journal articles
Magazine articles
Editorial: Reflections on the Page equation, laboratory work, and new concepts, TAPPI Journal May 2022
ABSTRACT: I began teaching paper physics to undergraduates in the late 1980s when the recognized giants in the field were still actively debating their subjects in the literature and scientific conferences.
Journal articles
Magazine articles
Improving refining efficiency with deflocculation, TAPPI Journal May 2022
ABSTRACT: The ability to load a refiner requires the formation of a fiber mat between opposing refiner bars. One of the consequences of this is the formation of flocs that persist through the refiner grooves and exit the refiner. These flocs interfere with sheet strength, requiring additional energy to make up the strength deficit. In addition, flocs can initiate string formation, resulting in machine efficiency issues such as cross-machine profile deterioration and the downtime required to correct it. Novel refiner plate modifications have been shown to improve refining efficiency in otherwise identical refiner plates. Energy savings are typically around 15% of gross refining energy on the basis of the treated stock, although much higher reductions have also been seen. Addressing this previously underappreciated flaw in conventional refining enables greenhouse gas reduction and other benefits related to sheet strength and machine efficiency.
Journal articles
Magazine articles
Web instability in the open draw and the impact on paper machine efficiency, TAPPI Journal May 2022
ABSTRACT: Paper is most likely to break in the first open draw on a paper machine where it is unsupported, wettest, and weakest. Tension is applied to peel the web from the roll surface, as well as minimize web flutter in the open draw. The average tension is well below the breaking point and is often set by adjusting the speed difference between the press and the next machine element by visually observing the behavior of the web. However, machine direction variations caused by instabilities in the paper machine can cause tension swings that exceed the strength of the web. Measurement of the web’s release point from press rolls on pilot and commercial paper machines was used to identify the cause of tension instabilities. Variations in the speed of the paper machine drives and the work of adhesion from the press roll surface were identified as key factors. Fluctuations of paper moisture, which affects the elastic modulus and strength of the web, appear to be less important.
Journal articles
Magazine articles
Effects of agitator blade scaling on mixing in dissolving tanks, TAPPI Journal April 2022
ABSTRACT: Hard calcium carbonate scale often forms on the agitators in smelt dissolving tanks. The effects of this scale on mixing are not well understood. While mixing in tanks has often been modeled in the literature, there have been no studies involving agitator scaling. To better understand the impact of agitator scaling on hydrodynamics and tank concentrations, a steady state, three-dimensional (3D) model has been developed for a smelt dissolving tank at a kraft pulp mill. In this work, four cases are compared: an agitator with no scaling, mild scaling, moderate scaling, and extreme scaling. The extreme scaling case is representative of scale buildup on a dissolving tank agitator that was significant enough that the agitator had to be stopped and cleaned. The reduction in the agitator fluid jet velocity is relatively small for the mild and moderate scaling cases, but it becomes more significant for the extreme scaling case, for which the results indicate that the mixing of the smelt with the weak wash is likely poor and that there would thus be a risk of smelt pooling.
Journal articles
Magazine articles
Comparative study of guar gum and its cationic derivatives as pre-flocculating polymers for PCC fillers in papermaking applications, TAPPI Journal April 2022
ABSTRACT: In this work, gums from guar seeds were evaluated as a potential precipitated calcium carbonate (PCC) filler pre-flocculant to induce functional filler in papermaking applications. In recent years, guar has been conidered one of the promising wet-end additives due to its abundance, rich source of hemicellulose content, and bio-degradability. However, application of guar gum in filler pretreatment methods for producing high ash paper has scarcely been reported. In this paper, the flocculating ability of three types of guar gum was established with charge analysis and turbidity (NTU) of the system at 1% and 5% for each gum: native gum (NG) having a degree of substitution (DS) of 0, and cationic gums having a DS value of 0.07 (CL) and 0.15 (CH). It was interesting to observe that even at a 5% dose of G, the charge density of PCC did not deviate much from the initial values. The system carried a weak negativeharge, resulting in an unstable colloidal suspension that led to PCC-PCC particle bridging. On the other hand, the operative mechanism of CL and CH during adsorption and PCC flocculation was predicted to be charge neutralization and electrostatic-patch formation, accompanied by particle bridging. Note that CL, with a maximum 47.5% eduction in residual turbidity of PCC at a 1% dose, was much more efficient in doing so than the other two gums; NG had a 40% maximum reduction in residual turbidity at a 5% dose and CH had a maximum 30% reduction at a 1% ose. Later on, floc formation and structure were correlated with optical and field emission scanning electron microscopy (FE-SEM) images. In the next set of trials, paper properties were determined by varying the different gum dosages from 0.2% to 5% at a constant dose of 20% filler. It is also noteworthy to mention that with 1% CL (low DS) dose, PCC retention increased by 39%, which also enhanced the tensile, tear, burst, and opacity properties by 11%, 19%, 5%, and 4.4%, respectively, without significantly affecting the bulk properties. Further, wide-angle X-ray diffraction (XRD) analysis nd Fourier transform infrared (FTIR) analysis revealed that pre-flocculating PCC with a 1% gum dose did not induce any change in crystalline transformation. Based on observation, it was found that cationic gums with low DS values re a better choice for maximizing the strength of paper while maintaining bulk and high opacity when pre-flocculaion is adopted to increase the filler retention in paper.
Journal articles
Magazine articles
Editorial: Impacts from using recycled pizza boxes in furnish: TAPPI Journal’s runner-up to 2021 Best Research Paper, TAPPI Journal August 2022
ABSTRACT: The runner-up to the 2021 TAPPI Journal Best Research Paper was “Incorporation of post-consumer pizza boxes in the recover Fiber Stream: Impact of grease on finished product quality."