Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Co-pulping of Trewia nudiflora and Trema orientalis, TAPPI Journal June 2023
ABSTRACT: Trewia nudiflora, a fast-growing species, was evaluated as a pulpwood. The a-cellulose content of this species was 40.4% with a Klason lignin of 21.5%. It was characterized by shorter fibers with a thin cell wall. The pulp yield was 40% with a kappa number of 16 at the conditions of 18% active alkali charge and 30% sulfidity for 2 h cooking at 170°C. T. nudiflora was similar to Trema orientalis in anatomical, morphological, and chemical composition; therefore, mixed chips at a 50:50 mixture ratio were cooked under optimum conditions. The pulp yield of mixed chip cooking was 45.4% with a kappa number of 19.4. The tensile and tear index of T. nudiflora pulps were 64.8 Nœm/g and 11.5 kPaœm2/g at 35 °SR, respectively. The mixed chips, T. nudiflora, and T. orientalis pulps showed above 81% brightness when bleached by D0(EP)D1 sequence using 20 kg chlorine dioxide (ClO2)/ton of pulp.
Journal articles
Magazine articles
Dissolution of wood components during hot water extraction of spruce, TAPPI Journal May 2023
ABSTRACT: The purpose of this study was to investigate the autohydrolysis of softwood, which is the main chemical operation in both hot water extraction and steam explosion. Control of the process and monitoring its course were ensured by the careful choice of experimental setup and conditions: a milled spruce material was extracted in a small flow-through reactor to minimize degradation of the dissolved material and to enable analysis of the resulting liquors extracted at selected time points. The obtained liquid and solid fractions were analyzed for sugar composition and acetic acid concentration. The results showed that partially degraded hemicelluloses were extracted; hemicelluloses side chains were cleaved off and detected as monomers, while deacetylation was limited. Chain scissions of cellulose were observed as a result of autohydrolysis.
Journal articles
Influence of base sheet properties on barrier coating performance, TAPPI Journal November 2025
ABSTRACT: Paper packaging offers a sustainable alternative to standard plastic-based materials, particularly for food and beverage applications. With reduced fiber treatment options like fluorochemicals, uncoated base stock often provides little-to-no effective barrier against liquid water, oil/grease, or moisture transmission. Despite the lack of natural barrier performance, base sheet properties can significantly influence the efficiency of applied waterbased barrier coatings. In this study, various base stock properties, such as caliper, porosity, roughness, and ash content, are reported to influence the barrier performance of styrene-acrylic and a copolymer of styrene-butadiene/styrene-acrylate based barrier coatings. These findings will help paper and board producers design better, more cost-effective, purposebuilt substrates for barrier applications in the packaging industry.
Journal articles
A laboratory-scale automated vacuum-assisted device for coating of cellulose nanofibrils onto paper, TAPPI Journal November 2025
ABSTRACT: An automated vacuum-assisted coating system was developed to deposit cellulose nanofibril (CNF) layers onto paper substrates, simulating potential industrial geometries while allowing precise control of web speed (10•20 m/min), vacuum time (up to 30 s), and applicator gap (0.5•0.9 mm). Vacuum assistance makes it possible to obtain coat weights over 5 g/m2 in a single pass and increases solids after coating from less than 10% to over 28%• 30%, reducing drying demand by more than 60%. Coat weights were tuned from 6 to over 11 g/m² by varying suspension solids (0.4•0.6 wt%), line speed, and filtration length (20•40 mm), with strong agreement between experimental data and model predictions. Barrier testing showed Kit test values for double folded samples of 9•12 and Gurley air resistances above 4 × 104 s once coat weights exceeded 7 g/m². Comparable performance was achieved with lower fines content CNF (60%) by increasing coat weight, providing technical flexibility and cost advantages for industrial scale-up.
Journal articles
The industry is entering a pivotal moment in which many of us find ourselves engaged in deep soul searching. Since the days of Francis Bacon when the illustrious triumvirate of gunpowder, the compass, and paper were the drivers of civilizations, our commu
The industry is entering a pivotal moment in which many of us find ourselves engaged in deep soul searching. Since the days of Francis Bacon when the illustrious triumvirate of gunpowder, the compass, and paper were the drivers of civilizations, our community has enjoyed a noble place at the table. Indeed, especially over the last 100 years, pulp and paper has quietly powered communication, commerce, and, more than ever today, packaging, thus representing a steady backbone for the continued stability of many global industries.
Journal articles
Reducing aox by increasing oxidation potential in the first
ABSTRACT An increase in the standard oxidation potential of the reinforcing agent in the first caustic extraction stage will reduce the amount of AOX in the stage's effluent. A chlorinated broumstock pulp was treated alternatively in a basic caustic extraction (E) stage, an oxygen-reinforced caustic extraction (EO) stage, and an extraction stage reinforced with oxygen and peroxide (EOP). An AOX reduction of up to 30% was obtained in the effluent from the peroxide-reinforced extraction stage. In addition to the brownstock work, using two different model lignin compounds, we ran tests using oxyen, potassium permanganate, hydrogen peroxide with oxygen, and ozone with oxygen-reinforced caustic stages. In all cases, increasing the oxidation potential of the reinforcing agent decreased the amount of AOX detected in the effluent.
Journal articles
An elliptical pore model for the mechanical properties of pa
An elliptical pore model for the mechanical properties of paper, TAPPI JOURNAL August 2015
Journal articles
Fast evaluation of spatial coating layer formation using ultraviolet scanner imaging
Fast evaluation of spatial coating layer formation using ultraviolet scanner imaging
Journal articles
Some observations towards improved predictive models for box compression strength, TAPPI JOURNAL August 2015
Some observations towards improved predictive models for box compression strength, TAPPI JOURNAL August 2015
Journal articles
A targeted approach to produce energy-efficient packaging materials from high-yield pulp, TAPPI Journal August 2025
ABSTRACT: Unlike fossil-based plastics, wood-based packaging materials can be produced in an ecofriendly manner using wood chip residuals from sawmills and pulpwood. To produce high-yield pulp like chemithermomechanical pulps (CTMPs) for paperboard and liquid packaging, it is crucial to reduce the electric energy consumption during fiber separation. The ultimate objective is to revolutionize paperboard production by achieving a middle-layer CTMP process that consumes less than 200 kilowatt-hours per metric ton (kWh/t), significantly improving from the current 500•600 kWh/t energy demand. Optimizing the CTMP impregnation process of sodium sulfite (Na2SO3) in wood chips is crucial for achieving uniform softening, ideally at the fiber level. The properties of the fibers are significantly affected by the content of lignin sulfonates within the walls of the fiber and the middle lamellae. In this study, we employed in-house developed X-ray fluorescence (XRF) techniques, validated by beamline measurements, to map the distribution of sulfonated lignin within fibers. It also seemed possible to enhance the surface area of lignin-rich pulp fibers while losing minimal bulk by refining them with well-optimized low consistency (LC) refining. We aimed to achieve a highly efficient separation of coniferous wood fibers by co-optimizing the sulfonation and the temperature in the preheater and chip refiner. Additionally, we explored how lignin’s softening behavior and potential crosslinking influence subsequent unit operations, including pressing, peroxide bleaching, and drying, following the defibration process. In defibration during chip refining, the maximum softening of wood fibers is preferred to maximize fiber preservation and minimize energy consumption. However, optimizing the stiffness of finished pulp fibers is preferable to reduce bulk loss during paperboard production. It can strive to optimize processes to develop stronger, lighter, and more sustainable composite packaging materials. Reducing environmental impact and electric energy can help create a more sustainable future.