Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
The potential of fly ash-based calcium silicate as paper filler: Physical properties and printability
The potential of fly ash-based calcium silicate as paper filler: Physical properties and printability, TAPPI JOURNAL October 2014
Journal articles
Editorial: Advances in Pulp Manufacture: A review of the 2012 PEERS Conference, TAPPI JOURNAL February 2013
Editorial: Advances in Pulp Manufacture: A review of the 2012 PEERS Conference, TAPPI JOURNAL February 2013
Journal articles
Implications of converting a kraft pulp mill to a dissolving pulp operation with a hemicellulose extraction stage, TAPPI JOURNAL February 2013
Implications of converting a kraft pulp mill to a dissolving pulp operation with a hemicellulose extraction stage, TAPPI JOURNAL February 2013
Journal articles
Brownstock washing fundamentals: enhancing drainage through chemistry â?¢ Part 1, TAPPI JOURNAL February 2013
Brownstock washing fundamentals: enhancing drainage through chemistry • Part 1, TAPPI JOURNAL February 2013
Journal articles
Examination of moisture content variation within an operational wet deck, TAPPI JOURNAL January 2013
Examination of moisture content variation within an operational wet deck, TAPPI JOURNAL January 2013
Journal articles
Guest Editorial: TAPPI Journal showcases the best of PEERS 2012, TAPPI JOURNAL July 2013
Guest Editorial: TAPPI Journal showcases the best of PEERS 2012, TAPPI JOURNAL July 2013
Journal articles
Magazine articles
Editorial: Nanocellulose: What's next?
Many of the researchers in this field in the late 1990s and early 2000s were challenged in terms of translation research issues due to the limited production capacity of nanocellulosics on a global stage. To address this call, several pilot-plant production plants have been developed and can now deliver NC on multikilo/ton scale as these issues are gradually being resolved.
Journal articles
Magazine articles
Prehydrolysis kraft pulping of jute cutting and caddis mixture for rayon production
ABSTRACT: Jute cutting, jute caddis, and cutting-caddis mixtures were prehydrolyzed by varying time and temperature to get about 90% prehydrolyzed yield. At the conditions of 170°C for 60 min of prehydrolysis, the yield for 100% jute cutting was 76.3%, while the same for jute caddis was only 67.9%. But with prehydrolysis at 150°C for 60 min, the yield was 90% for jute cutting, where 49.94% of original pentosan was dissolved and prehydrolysis of jute caddis at 140°C in 60 min yielded 86.4% solid residue. Jute cutting-caddis mixed prehydrolysis was done at 140°C for 30 min and yielded 92% solid residue for 50:50 cutting-caddis mixtures, where pentosan dissolution was only 29%. Prehydrolyzed jute cutting, jute caddis, and cutting-caddis mixtures were subsequently kraft cooked. Pulp yield was only 40.9% for 100% jute cutting prehydrolyzed at 170°C for 60 min, which was 10.9% lower than the prehydrolysis at 140°C. For jute cutting-caddis mixed prehydrolysis at 140°C for 45 min followed by kraft cooking, pulp yield decreased by 3.3% from the 100% cutting to 50% caddis in the mixture, but 75% caddis in the mixture decreased pulp yield by 6.7%. The kappa number 50:50 cutting-caddis mixture was only 11.3. Pulp bleachability improved with increasing jute cutting proportion in the cutting-caddis mixture pulp.
Journal articles
Magazine articles
Sources, collection, and handling of noncondensible gases in modern kraft pulp mills
ABSTRACT: This work describes and discusses sources of noncondensible gases (NCG) in modern kraft pulp mills and modern NCG collection from process units where odor emissions can occur if these gases are released to the surroundings. A mill-wide overview of NCG sources and collection in modern pulp mills is provided. Using modern practices, malodorous gases can be collected to the extent that a pulp mill is essentially odor free. The key to limiting complaint-causing odors is prevention of these emissions during process disturbances, equipment malfunctions, operator errors, and other unforeseen occurrences.
Journal articles
Magazine articles
Research needs for nanocellulose commercialization and applications
INTRODUCTION: This short review deals with some applications and research needs for nanocellulosic (NC) materials; primarily cellulose nanocrystals (CNC), cellulose nanofibers (CNF), and bacterial cellulose (BC). Whereas CNC and BC materials are fairly homogenous, CNF materials represent a wide sector of different materials, often with a high heterogeneity. This is due to different pretreatment methods (mechanical, chemical, enzymatic), woodbased or agricultural-based materials, delignification and bleaching procedures, etc. The purpose of this comprehensive review is not to discuss the various production methods, for which the reader may consult with a selected number of reviews [1-6]; thus, the focus is on practical applications. Practical applications and potential markets were also discussed some years ago by other investigators [7-8]. Upscaling and choice of pretreatment methods, as well as economic considerations and different business models, have also been discussed, along with: œ Toxicity and environmental issues [9-10] œ The complex characterization of cellulose nanomaterials [4] The reader should also be aware of new contenders to the three classic groups of cellulosic nanomaterials, which are already in a commercial phase. These include cellulose filaments [11-12] and materials from mechanical grinding processes [13], and these materials may be nanostructures or not, depending on our classification. Finally, as indicated by the editorial on p. 275, scientists are currently taking a deep dive into the fundamental features of nanocellulosic materials [14-15].