Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Decision-making process for the identification of preferred
Decision-making process for the identification of preferred lignin-based biorefinery strategies, TAPPI JOURNAL April 2017
Journal articles
Magazine articles
Evaluation of the particle size of organosolv lignin in the
Evaluation of the particle size of organosolv lignin in the synthesis of resol resins for plywood and their performance on fire spreading, TAPPI JOURNAL July 2017
Journal articles
Magazine articles
Commercially relevant water vapor barrier properties of high amylose starch acetates: Fact or fiction?, TAPPI Journal September 2021
ABSTRACT: Starches have recently regained attention as ecofriendly barrier materials due to the increased demand for sustainable packaging. They are easily processable by conventional plastics processing equipment and have been utilized for oil and grease barrier applications. While starches have excellent oxygen barrier properties and decent water barrier properties at low relative humidity (RH), they are moisture sensitive, as demonstrated by the deterioration of the barrier properties at higher RH values. Starch esters are chemically modified starches where the hydroxyl group of the starch has been substituted by other moieties such as acetates. This imparts hydrophobicity to starches and has been claimed as a good way of retaining water vapor barrier properties of starches, even at high RH conditions. We studied the water vapor barrier properties of one class of starch esters, i.e., high amylose starch acetates that were assumed to have good water vapor barrier properties. Our investigations found that with a high degree of substitution of hydroxyl groups, the modified starches did indeed show improvements in water vapor response as compared to pure high amylose starch films; however, the barrier properties were orders of magnitude lower than commercially used water vapor barriers like polyethylene. Even though these materials had improved water vapor barrier response, high amylose starch acetates are likely unsuitable as water vapor barriers by themselves, as implied by previous literature studies and patents.
Journal articles
Magazine articles
Comparative study of guar gum and its cationic derivatives as pre-flocculating polymers for PCC fillers in papermaking applications, TAPPI Journal April 2022
ABSTRACT: In this work, gums from guar seeds were evaluated as a potential precipitated calcium carbonate (PCC) filler pre-flocculant to induce functional filler in papermaking applications. In recent years, guar has been conidered one of the promising wet-end additives due to its abundance, rich source of hemicellulose content, and bio-degradability. However, application of guar gum in filler pretreatment methods for producing high ash paper has scarcely been reported. In this paper, the flocculating ability of three types of guar gum was established with charge analysis and turbidity (NTU) of the system at 1% and 5% for each gum: native gum (NG) having a degree of substitution (DS) of 0, and cationic gums having a DS value of 0.07 (CL) and 0.15 (CH). It was interesting to observe that even at a 5% dose of G, the charge density of PCC did not deviate much from the initial values. The system carried a weak negativeharge, resulting in an unstable colloidal suspension that led to PCC-PCC particle bridging. On the other hand, the operative mechanism of CL and CH during adsorption and PCC flocculation was predicted to be charge neutralization and electrostatic-patch formation, accompanied by particle bridging. Note that CL, with a maximum 47.5% eduction in residual turbidity of PCC at a 1% dose, was much more efficient in doing so than the other two gums; NG had a 40% maximum reduction in residual turbidity at a 5% dose and CH had a maximum 30% reduction at a 1% ose. Later on, floc formation and structure were correlated with optical and field emission scanning electron microscopy (FE-SEM) images. In the next set of trials, paper properties were determined by varying the different gum dosages from 0.2% to 5% at a constant dose of 20% filler. It is also noteworthy to mention that with 1% CL (low DS) dose, PCC retention increased by 39%, which also enhanced the tensile, tear, burst, and opacity properties by 11%, 19%, 5%, and 4.4%, respectively, without significantly affecting the bulk properties. Further, wide-angle X-ray diffraction (XRD) analysis nd Fourier transform infrared (FTIR) analysis revealed that pre-flocculating PCC with a 1% gum dose did not induce any change in crystalline transformation. Based on observation, it was found that cationic gums with low DS values re a better choice for maximizing the strength of paper while maintaining bulk and high opacity when pre-flocculaion is adopted to increase the filler retention in paper.
Journal articles
Non-process elements in the lime cycle: New findings regarding NPE distribution and lime mud filterability, TAPPI Journal July 2026
ABSTRACT: Proper functioning of the recausticizing cycle is crucial for securing a stable white liquor supply for a pulp mill. Common runnability problems in the modern lime cycle, such as low filterability and poor dewatering of lime mud, high dead load, or ring formation in the lime kiln, are often caused by accumulation of non-process elements (NPEs). This project attempted to verify the traditional rules of thumb regarding the chemical behavior of NPEs: magnesium (Mg), aluminum (Al), silicon (Si), phosphorus (P), zinc (Zn), manganese (Mn), iron (Fe), copper (Cu), barium (Ba), cadmium (Cd), and lead (Pb) in the causticizing reaction, and to investigate the reasons behind poor lime mud filterability. First, a standardized method for measuring filterability of lime mud was developed. Next, a series of recausticizing experiments, followed by immediate filtration trials, was conducted using mill green liquors, laboratory-made synthetic green liquor, reburned lime/makeup mix, and extra NPE additions. It was found that sodium (Na), potassium (K), and sulfur (S) followed the liquid phase, as expected, while Mg, P, and Ba, but also Pb, Cu, and Cd, showed low solubility and accumulated in the lime mud. The Si and Al accumulated in the lime mud even though the soluble content in liquor was high, while the behavior of Mn, Fe, and Zn was more complex. Based on these results, tentative solubility limits for NPEs were suggested as a first estimate for the maximum possible concentrations of NPEs in mill white liquor. The causticization-filtration experiments revealed that overliming and high content of Mg in green liquor clearly led to lower filterability, but our addition of Si did not have such an effect. As differences in particle size and size distribution have a certain impact on the filtration resistance, the lime mud sedimentation behavior, combined with other characterization methods, might be used as an indication for the filterability. Finally, a list of recommendations for pulp mills was formulated that starts with establishing a comprehensive standard for a lime mud with good filterability. This standard can be used as a benchmark for comparison any time a lime cycle runnability problem is identified.
Journal articles
Black liquor spray properties in-furnace conditions for swirl cone nozzles, TAPPI Journal July 2026
ABSTRACT: Recovery boiler furnace operation is controlled for high chemical recovery, high steam production, and low emissions. Good control allows long runs with minimum cleaning without expensive shutdowns. An essential variable affecting boiler operation is black liquor spraying into the furnace. Poorly controlled black liquor spraying causes difficulties, e.g., in chemical recovery, fouling of heat transfer surfaces, and decreased energy production. A challenging measurement strategy with three different swirl cone nozzles . types A, C, and T . was carried out at a mill in the United States. Black liquor spray properties were measured under in-furnace conditions for flow rates of 2.0 L/s to 3.0 L/s. Three spraying temperatures of 119™‹C, 122™‹C, and 126™‹C, which were 2™‹C, 5™‹C, and 9™‹C above the boiling point (ƒ¢Te), were tested. These flow rates and temperatures are typical for industrial nozzle sizes with exit orifice sizes of 17 mm and 22 mm. An imaging method to measure droplet size in a highly challenging furnace environment was developed. Droplet volume median diameter (Dv50) for nozzles A, C, and T varied between 7 mm to 4 mm, 7 mm to 5 mm, and 8 mm to 6 mm, depending on the flow rate and temperature. The high number of droplets detected by the analysis program enabled data fitting into statistical correlations. The size and width parameters for the Rosin™]Rammer droplet size distribution function could be defined. The droplet size distribution was found to be surprisingly wide, probably because of swollen droplets. Spray velocity was measured in two locations, 5 cm from the nozzle and 1.8 m from the nozzle. Near the nozzle, the average velocity increased from 7.3 m/s to 13 m/s when the flow rate was increased from 2 L/s to 3 L/s. Increase of black liquor temperature increased spray velocity in most of the cases. At the distance of 1.8 m from the nozzle, average spray velocities varied between 4.0 m/s to 11 m/s, depending on nozzle geometry, flow rate, and temperature. The opening angles of the spray for nozzles A and C varied between 57™‹ to 78™‹. The opening angle of nozzle T with flow guide varied between 48™‹ to 56™‹. The highest penetration of the spray was estimated for nozzle T because of the narrow spray and large droplets.
Journal articles
Physico-mechanical and ethylene scavenging properties of active packaging from Bambusa fibers modified with TiO2 /Cu2O composite, TAPPI Journal February 2026
ABSTRACT: The physico-mechanical and ethylene scavenging properties of active packaging consisting of paper prepared from bamboo (Bambusa vulgaris) fibers loaded with varying concentrations of nano titanium dioxide/cuprous oxide (TiO2/Cu2O) composite was investigated for its ability to delay ripening of Philippine climacteric fruits. Tests of paper containing 1% to 5% TiO2/Cu2O showed no or limited negative impact on its physical, optical, and mechanical properties. Images from a field emission scanning electron microscope equipped with energy-dispersive X-ray spectroscopy (FESEM-EDS) showed dispersion and agglomeration of TiO2/Cu2O nanoparticles on the paper surface. The percent weight of titanium and copper increased with increasing metal oxide composite concentration used in this study. Attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy indicated small shifts in band intensity at 3330 cm-1 and 1100 cm-1 in the hydroxyl (O-H) and C-O regions, respectively, suggesting possible chemical or physical interactions between the metal oxide and paper. Contact angle measurement suggest- ed that TiO2/Cu2O nanoparticles may have imparted paper hydrophobicity at 3% & 5% concentration, possibly through increased microscale roughness. The ethylene scavenging experiment indicated that there was a significant delay in the ripening process of mango and tomato when packed in paper doped with 3% and 5% TiO2/Cu2O. The fruits were greener with a firmer texture compared with untreated control after three days of storage under natural light and ambient condition. The preliminary results suggested that 3% &5% TiO2/Cu2O active packaging modification can remove ethylene from the fruit's storage environment, extending shelf life and maintain quality for three days. This simple technique could have potential economic benefits for the fruit industry by directly reducing post-harvest waste, and the delayed ripening could provide flexibility in supply chain management.
Journal articles
Exploratory study on how sub-ply fiber orientation affects t
ABSTRACT: The transition to 100% biobased packaging presents considerable challenges, particularly in the development of a petroleum-free barrier. Generally, biobased barriers exhibit lower flexibility compared to traditional barriers, thereby increasing the risk of cracking during the converting process. The present study examines the possibility of optimizing the substrate to reduce cracking in brittle barriers. Five three-ply composites were fabricated using commercial paperboard to enable a composite with different fiber orientation in the individual plies. The different orientations achieved varying mechanical properties, including strain-atbreak and folding resistance, with a ranking that is comparable to a standard multi-ply paperboard. The composites were subjected to creasing at five distinct depths to assess the area percent of barrier cracks across the crease bead. Micro-cracks appeared on the surface before larger coating cracks were registered. As expected, the area percent of barrier cracks increased significantly with greater creasing depths. The orientation of the bulky middle ply showed little difference in the cracking propensity. However, by replacing the stiffer bottom ply with a ply of lower stiffness, the cracking propensity was significantly reduced without a substantial loss in mechanical properties. Hence, these findings indicate that it is possible to reduce the cracks in the barrier by modifying the fiber orientation in the different plies.
Journal articles
Improving barrier performance of coated paper and paperboard
ABSTRACT: Market demand for barrier coated packaging paper and paperboard has been on a steady rise and is forecasted to further increase. As a result, there is a continued interest in improving barrier coating functionalities, which is currently an active area of investigation. In this work, a multi-layer approach was adopted that involved applying a biowax emulsion, latex, or a combination of biowax and latex top coating layer onto the kaolin/latex (20/80, 50/50, 65/35, or 70/30) precoated solid bleached sulfate (SBS) paperboard. Our main objective was to demonstrate the effect of these top coating layers on various barrier properties, especially water vapor transmission rate (WVTR) at high relative humidity (RH) and high temperature (90% RH; 38°C), known as tropical/jungle test conditions. While the top coat with latex and/or biowax showed dramatic improvement in both water resistance (Cobb) and WVTR, the biowax coating increased contact angle significantly compared to the latex top coat. Contact angle increased from about 65° for the latex top coat to as high as 96° for the biowax top coat. Generally, it is much more difficult to improve WVTR at the jungle conditions below 100 g/m2/day, even with the high aspect ratio platy pigment. However, using the coating strategies adopted in this study, we were able to achieve WVTR values notably below 50 g/m2/day at the tropical test conditions, as well as significant improvements in regard to fold crack barrier integrity at high kaolin clay usage.
Journal articles
Prediction of residual calcium carbonate (CaCO3) in the lime
ABSTRACT: In a kraft pulp mill, the rotary lime kiln is responsible for converting calcium carbonate (CaCO3) into calcium oxide (CaO) to be reused in the causticizing plant. An important parameter of the calcination efficiency and the product quality is the amount of CaCO3 not converted to CaO, commonly defined as residual carbonate. This parameter is usually determined through laboratory analysis, which introduces delays in process control and limits the ability to make timely operational adjustments. This work presents a predictive model that functions as a soft sensor for the residual carbonate in a lime kiln of a Brazilian kraft pulp mill. This model was able to estimate residual CaCO3 every 30 min using routinely measured online process variables, which is a considerable reduction from the 6-h average laboratory measurement. The correlation coefficient (r) between the model predictions and the mill values was 0.83, with a mean absolute error (MAE) of 0.33%. Considering the effect of the residence time throughout the lime kiln proved to be decisive in obtaining a satisfactory prediction result. After model validation, a variable importance analysis showed that the carbon monoxide (CO) concentration in the stack flue gas (in ppm), secondary air temperature (in oC), and fan speed (in %) were the most influential variables in predicting the residual carbonate content. Combined with commonly used operation expertise, this subset of variables can serve as additional information to achieve smoother lime kiln operation.