Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Black liquor evaporator upgrades— life cycle cost analysis, TAPPI Journal March 2021
ABSTRACT: Black liquor evaporation is generally the most energy intensive unit operation in a pulp and paper manufacturing facility. The black liquor evaporators can represent a third or more of the total mill steam usage, followed by the paper machine and digester. Evaporator steam economy is defined as the unit mass of steam required to evaporate a unit mass of water from black liquor (i.e., lb/lb or kg/kg.) The economy is determined by the number of effects in an evaporator train and the system configuration. Older systems use four to six effects, most of which are the long tube vertical rising film type. Newer systems may be designed with seven or even eight effects using falling film and forced circulation crystallization technology for high product solids. The median age of all North American evaporator systems is 44 years. Roughly 25% of the current North American operating systems are 54 years or older. Older systems require more periodic maintenance and have a higher risk of unplanned downtime. Also, older systems have chronic issues with persistent liquor and vapor leaks, shell wall thinning, corrosion, and plugged tubes. Often these issues worsen to the point of requiring rebuild or replacement. When considering the age, technology, and lower efficiency of older systems, a major rebuild or new system may be warranted. The intent of this paper is to review the current state of black liquor evaporator systems in North America and present a basic method for determining whether a major rebuild or new installation is warrant-ed using total life cycle cost analysis (LCCA).
Journal articles
Magazine articles
Impact and feasibility of a membrane pre-concentration step in kraft recovery, TAPPI Journal May 2021
ABSTRACT: Emerging robust membrane systems can perform the first section of black liquor (BL) concentration by separating clean water from the black liquor stream using only mechanical pressure. By doing so, they can reduce the steam and energy required for BL concentration. Because of the high osmotic pressure of strong BL, a membrane system would not replace evaporators but would operate in series, performing the first section of BL concentration. In this work, we use a multi-effect evaporator (MEE) model to quantify the steam and energy savings associated with installing membrane systems of different sizes. When maintaining a constant BL solids throughput, we find that a pulp mill could reduce steam usage in its evaporators by up to 65%. Alternatively, a membrane system could also serve to increase BL throughput of the recovery train. We find that a membrane system capable of concentrating BL to 25% could double the BL solids throughput of a mill’s evaporators at the same steam usage. We also demonstrate that installing a membrane system before an MEE would minimally affect key operating parameters such as steam pressures and BL solids concentrations in each effect. This indicates that installing a membrane pre-concentration system would be nonintrusive to a mill’s operations.
Journal articles
Magazine articles
In-situ green synthesis and adsorption on methylene blue of copper-based metal organic framework/cellulose/chitosan (CCTSA/HKUST-1) composite aerogel, TAPPI Journal October 2024
ABSTRACT: In order to explore the application of metal-organic frameworks (MOFs) in environmental and water treatment fields, a new composite aerogel of HKUST-1/cellulose/chitosan (CCTSA/HKUST-1) with better hydrostability was synthesized by an in-situ synthesis method combining covalent cross-linking and solvothermal methods as an efficient adsorbent for methylene blue (MB). The composite aerogel (CCTSA) obtained by covalent cross-linking of cellulose (CE) and chitosan (CTS) exhibited excellent stability under strong acid and solvent-thermal conditions. With the increase of CTS content, it was beneficial to the in-situ synthesis of HKUST-1, as well as to increase the mass loading rate of HKUST-1 to 37.06%, while the Brunauer-Emmett-Teller (BET) specific surface area of CCTSA/HKUST-1 composite aerogel reached 945.123 m2·g-1, which was much higher than that of the CCTSA composite aerogel (14.489 m2·g-1). The CCTSA/ HKUST-1 composite aerogel exhibited excellent adsorption capacity (537.6 mg·g-1) on MB solution, and cyclic adsorption could be achieved. This study proposes a concept of valorization of alkaline peroxide mechanical pulping (APMP) waste liquor to hemicellulose-based hydrogel. This hemicellulose-based hydrogel exhibits a sensitive temperature/pH dual response. Hemicellulose-based hydrogels swell or shrink through the change of hydrogen bond/electrostatic repulsion/charge screening. They also show good water absorption and water retention properties.
Journal articles
Magazine articles
Biofuels in lime kilns • Operating experience in the Nordic pulp and paper industry, TAPPI Journal October 2024
ABSTRACT: The lime reburning process is a central part of the chemical pulp mill. It is energy intensive and consumes large amounts of fossil fuel, globally consuming about 50 terawatt-hours (TWh) of fuel per year. Conversion to operation with biofuel is interesting, both to reduce carbon dioxide emissions and to reduce costs. Researchers interviewed managers in mills that use solid, liquid, or gasified biofuels to replace fuel oil or natural gas in their lime kilns, and they conducted surveys related to fuel consumption and operations and maintenance. In Sweden and Finland, there were ten mills in 2020 using biomass powder or gasified biomass as the primary fuel, and two more installations were under construction. There were also nine installations in operation or under construction outside the Nordic countries. Fourteen mills in Sweden and two mills in Finland used tall oil pitch as the main fuel. Fuel consumption in Swedish lime kilns was 3.8 TWh in 2020, and 90% of this energy was supplied with biofuels. Of about 4.2 TWh used in Finnish lime kilns, approximately 45% was supplied with biofuels. Developments in the design of the fuel supply system include belt dryers being used in all new installations and mass flow metered dosing systems being used in most new pulverized fuel installations. Bark gasifiers have increased considerably in size. Lignin powder firing has been established as a proven option. A solution for many Swedish and Finnish mills is the use of tall oil pitch as a replacement for fuel oil.
Journal articles
Magazine articles
Model development for real oxygen delignification processes, TAPPI Journal October 2024
ABSTRACT: Previous extensive work has been done on modeling the oxygen delignification process, based on how the basic parameters, i.e., temperature, kappa number, concentration of alkali, and concentration of oxygen, affect the delignification rate. However, these models are not used extensively to evaluate the performance of real processes, primarily because they have not been able to properly consider all the essential issues affecting delignification in practice. Such issues include the mass transfer and consumption of oxygen, which defines the concentration of dissolved oxygen in the process, and the effect of that concentration on the delignification rate. In this paper, a new way to model the oxygen delignification process is used in which these parameters, among other smaller matters, are taken into account. The basic model and its parameters were defined by the information obtained from the literature, delignification made in the laboratory tests, and mill processes and mill tests. An essential aspect of these studies was the information obtained from the oxygen concentration measured in the residual gas obtained from the top of the reactor. With the aid of this measurement, it was possible to define more accurately the consumption of oxygen and partial pressure of oxygen that define the concentration of dissolved oxygen in the reactor. Using mill experiments, a model was formed that predicts the operation of the oxygen delignification process. The model was used to show how much the process could be improved by optimizing the charge of the oxygen. The mill experiments also confirmed that mass transfer of oxygen is modeled correctly enough, except when the charge of oxygen is very low and/or the mixing is not efficient enough. In that case, there is variation in the concentration of oxygen in the process that should be taken into account in the modeling.
Journal articles
Magazine articles
Investigation of the influencing factors in odor emission from wet-end white water, TAPPI Journal October 2020
ABSTRACT: Emission of malodorous gases, such as volatile organic compounds (VOCs), hydrogen sulfide (H2S), and ammonia (NH3) during pulping and papermaking has caused certain harm to the air environment and human health. This paper investigated the influencing factors of odor emission from wet-end white water during the production of bobbin paper in a papermaking mill using old corrugated containers (OCC) as raw material. The concentration of malodorous gases emitted from wet-end white water was determined with pump-suction gas detectors. The results indicated that low temperature could limit the release of malodorous gases from white water. Specifically, no total volatile organic compounds (TVOC), H2S, and NH3 was detected at a temperature of 15°C. The concentrations of malodorous gases were slightly increased when temperature increased to 25°C. When temperature was 55°C, the released concentrations of TVOC, H2S, and NH3 were 22.3 mg/m3, 5.91 mg/m3, and 2.78 mg/m3, respectively. Therefore, the content of malodorous gases significantly increased with the temperature increase. The stirring of white water accelerated the release of malodorous gases, and the release rate sped up as the stirring speed increased. However, the total amount of malodorous gases released were basically the same as the static state. Furthermore, the higher the concentration of white water, the greater the amount of malodorous gases released. The pH had little influence on the TVOC release, whereas it significantly affected the release of H2S and NH3. With the increase of pH value, the released amount of H2S and NH3 gradually decreased. When pH reached 9.0, the release amount of H2S and NH3 was almost zero, proving that an alkaline condition inhibits the release of H2S and NH3.
Journal articles
Magazine articles
Characterization of chia plant (Salvia hispanica) for pulping, TAPPI Journal October 2020
ABSTRACT: In this paper, chia plant was characterized in terms of chemical, morphological, and anatomical properties. Chia plant was characterized with low a-cellulose (30.5%); moderate lignin (23.2%) with syringyl to guaiacyl ratio of 1.41; and shorter fiber length (0.67 mm) with thinner cell wall (1.91 µm) and good flexibility coefficient (71.44). Anatomical features showed that chia plant consists of vessels, fibers, parenchyma cells, and collenchyma cells. Chia plant pulping was evaluated in soda-anthraquinone (soda-AQ) and formic acid/peroxyformic acid (FA/PFA) processes. Chia plant was difficult to delignify in the alkaline process. The FA/PFA process produced higher pulp yield at the same kappa number than the soda-AQ process. Unbleached soda-AQ chia pulp exhibited good properties in terms of tensile, bursting, and tearing strengths, even at the unrefined stage, due to high drainability of the pulps. Alkaline peroxide bleached FA/PFA pulp exhibited better papermaking properties and 2% higher brightness than the D0(EP)D1 bleached soda-AQ pulp.
Journal articles
Magazine articles
Pulp and paper mills: The original biorefineries — past performance and limitations to future opportunities, TAPPI Journal October 2023
ABSTRACT: Pulp mills have been biorefineries since the invention of the Tomlinson recovery boiler. Unfortunately, the paper industry has done a poor job explaining that concept to the general public. A number of bioproducts in everyday use have been produced by pulp mills for several decades, and new products are routinely being developed. Modern research efforts over the last couple of decades have focused on producing even more products from pulp and paper mills through capacity enhancement and the development of value-added products and liquid transportation fuels to enhance paper mill profitability. Some of these efforts, often referred to as modern biorefineries, have focused so heavily on product development that they have ignored operating and process realities that limit the transformation of pulp and paper mills from the current limited number of bioproducts produced today to economic scale production of these value-added products. In this paper, several of these limitations are addressed. In addition, there are several supply chain, marketing, product quality, and economic realities limiting the value potential for these wholesale conversions of pulp mills into multiproduct modern biorefineries. Finally, the conservative nature and capital intensity of the pulp and paper industries provide a difficult hurdle for conversion to the modern biorefinery concept. These issues are also reviewed.
Journal articles
Magazine articles
Kraft pulp viscosity as a predictor of paper strength: Its uses and abuses, TAPPI Journal October 2023
ABSTRACT: For bleached kraft pulps, two factors govern paper strength: the individual fiber strength, and the bond strength that adheres the individual fibers together in the paper matrix. Inherent fiber strength is related to the length of the carbohydrate polymers, also known as the degree of polymerization (DP). Average DP (DP) is inferred by performing pulp viscosity measurements. Under certain circumstances during kraft pulping and bleaching, the average polymer lengths can be shortened, resulting in lower pulp viscosity, and may indicate fiber damage. Fiber damage typically manifests itself as a reduction in tear strength for well-bonded handsheets.This paper will review the literature on how pulp viscosity can predict paper/fiber strength and how it can be used as a diagnostic tool. It can be a means to monitor pulp quality during pulping and bleaching, as well as to alert when such operations approach a critical threshold. However, viscosity losses must be carefully and judiciously analyzed. Like most diagnostic tools, viscosity measurements can be misused and abused, which can lead to incorrect inferences about intrinsic fiber strength. This review will also cover these misuses. The overall goal is to provide the papermaker a better understanding of what pulp viscosity is, how it correlates to potential sheet strength, and what its limitations are. It will be illustrated that when pulp viscosity drops below a critical value, it will indicate an appreciable deterioration in the paper’s tear and tensile strength.
Journal articles
CFD-Based Modeling of Kraft Char Beds â?¢ Part 2: A Study on the Effects of Droplet Size and Bed Shape on Bed Processes, TAPPI JOURNAL February 2010
CFD-Based Modeling of Kraft Char Beds • Part 2: A Study on the Effects of Droplet Size and Bed Shape on Bed Processes, TAPPI JOURNAL February 2010