Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Polyvinyl alcohol as foaming agent in foam formed paper, TAPPI JOURNAL August 2019
ABSTRACT: The use of polyvinyl alcohol (PVOH or PVA) as a foaming agent in foam formed paper was investigated. Polyvinyl alcohol is a linear, nonionic water-soluble polymer. It has hydrophobic and hydrophilic parts that give it a surface-active character. PVOH is mainly characterized by degree of hydrolysis and molar mass. Degree of hydrolysis is given as mol-% hydroxyl groups on the polymer. Molar mass is measured indirectly by measuring the viscosity of a 4% PVOH solution. The results show that the degree of hydrolysis of PVOH had a strong effect on the foamability of PVOH. Foamability decreased strongly when the degree of hydrolysis increased from 88 to 98 mol-%. The effect of molar mass on foamability was weaker. We saw an increase in foam stability and bubble size with increasing molar mass, but we did not see any effect on maximum air content. PVOH dosage needed to reach >70% air content (F) varied from 2 g/l up to 10.5 g/l, and the lowest addition levels of PVOH needed were achieved with a low molar mass PVOH with a low degree of hydrolysis. The best strength properties were achieved when using fully hydrolyzed PVOH as the foaming agent. Strength properties (both in- and out-of-plane) of samples made using PVOH were better than those made using an anionic foaming agent (sodium dodecyl sulfate, SDS). By adding PVOH binder fibers to the pulp, we were able to further enhance the strength properties of paper and board.
Journal articles
Magazine articles
Real-time monitoring of bubble size distribution in a foam forming process, TAPPI JOURNAL August 2019
ABSTRACT: Foam forming is an intricate option to lessen fiber flocculation and to get better energy and water efficiency when making fiber-based products. Developed during the 1970s, this approach has recently received renewed attention, mainly because it also offers possibilities to widen the fiber-based product portfolios with novel and more valuable products. In addition to air content, bubble size is the most important property of foam. Foam quality control is essential for building real-world foam forming processes. In this work, we show how bubble size can be monitored with direct optical imaging in real time in real process conditions, and how such analysis helps adjust foam quality and discover process faults in foam forming.
Journal articles
Magazine articles
Progress in foam forming technology, TAPPI JOURNAL August 2019
ABSTRACT: This paper summarizes recent developments in foam forming that were mainly carried out in pilot scale. In addition to improving the efficiency of existing processes and allowing better uniformity in material, a wide variety of raw materials can be utilized in foam forming. The focus of this paper is thin webs—papers, boards and foam-laid nonwovens, along with the pilot scale results obtained at VTT in Finland. For paper and board grades, the most direct advantage of foam forming is the potential to produce very uniform webs from longer and coarser fibers and obtain material savings through that. Another main point is increased solids content after a wet press, which may lead to significant energy savings in thermal drying. Finally, the potential to introduce “difficult” raw materials like long synthetic or manmade fibers into a papermaking process enables the manufacturing of novel products in an existing production line. This paper also briefly discusses other interesting foam-based applications, including insulation and absorbing materials, foam-laid nonwovens, and materials for replacing plastics.
Journal articles
Magazine articles
Critical parameters for tall oil separation I: The importance of ration of fatty acids to rosin acids, TAPPI Journal September 2019
ABSTRACT: Tall oil is a valuable byproduct in chemical pulping of wood, and its fractions have a large spectrum of applications as chemical precursors, detergents, and fuel. High recovery of tall oil is important for the economic and environmental profile of chemical pulp mills. The purpose of this study was to investigate critical parameters of tall oil separation from black liquor. To investigate this in a controlled way, we developed a model test system using a “synthetic” black liquor (active cooking chemicals OH- and HS- ions), a complete process for soap skimming, and determination of recovered tall oil based on solvent extraction and colorimetric analysis, with good reproducibility. We used the developed system to study the effect of the ratio of fatty acids to rosin acids on tall oil separation. When high amounts of rosin acids were present, tall oil recovery was low, while high content of fatty acids above 60% significantly promoted tall oil separation. Therefore, manipulating the content of fatty acids in black liquor before the soap skimming step can significantly affect the tall oil solubility, and hence its separation. The findings open up chemical ways to improve the tall oil yield.
Journal articles
Magazine articles
A new technique for the measurement of show-through mottle of fine paper, TAPPI Journal September 2019
ABSTRACT: Mottling within print-through and show-through is caused by the variability of the local optical properties of the sheet. This mottling is visually disturbing and a mark of poor paper quality. The ability to predict print-through mottle of printed paper by measuring show-through mottle on the unprinted sheet would be a valuable asset for paper machine control.We examined the relationship between print-through mottle and show-through mottle. We worked with nine samples of 60 lb. uncoated fine paper (90 g/m2), from various North American paper companies, that were printed on an offset press, 400K (400% Black), on both sides. A show-through mottle instrumental determination technique was developed using an existing Fast Fourier Transform-based algorithm. The nine samples examined were ranked similarly by the visual evaluation of print-through mottle and by the instrumental determination of show-through mottle. We thus established that show-through on the unprinted sheet can be used as a reliable predictor of print-through, therefore saving time and money for papermakers. We also found a significant two-sidedness in show-through for some of the samples.
Journal articles
Dynamic Modeling of a Paper Machine, Part II: Evaluation of Wet-End Model Dynamics, TAPPI JOURNAL, February 2007
Dynamic Modeling of a Paper Machine, Part II: Evaluation of Wet-End Model Dynamics, TAPPI JOURNAL, February 2007
Journal articles
Optimization of Rectangular Pulp Stock Mixing Chest Dimensions Using Dynamic Tests, TAPPI JOURNAL, February 2007
Optimization of Rectangular Pulp Stock Mixing Chest Dimensions Using Dynamic Tests, TAPPI JOURNAL, February 2007
Journal articles
Substitution of Hardwood Bleached Kraft Pulp with Aspen High-Yield Pulp in LWC Wood-Free Papers, Part 2: Impact on Coated Paper Quality, TAPPI JOURNAL, January 2007
Substitution of Hardwood Bleached Kraft Pulp with Aspen High-Yield Pulp in LWC Wood-Free Papers, Part 2: Impact on Coated Paper Quality, TAPPI JOURNAL, January 2007
Journal articles
Life-cycle thinking in the pulp and paper industry, Part I: Current practices and most promising avenues, TAPPI JOURNAL, July 2007
Life-cycle thinking in the pulp and paper industry, Part I: Current practices and most promising avenues, TAPPI JOURNAL, July 2007
Journal articles
Biogenic H2SO4 Corrosion of Concrete in Oxygen Activated Sludge Bioreactors, TAPPI JOURNAL, June 2007
Biogenic H2SO4 Corrosion of Concrete in Oxygen Activated Sludge Bioreactors, TAPPI JOURNAL, June 2007