Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Non-process elements in the recovery cycle of six Finnish kraft pulp mills, TAPPI Journal March 2023
ABSTRACT: In this work, the aim was to study the distribution and accumulation of the non-process elements (NPEs) in the recovery cycle of Finnish pulp mills and look at whether the geographical location (North vs. South) correlates with the current Finnish NPE levels. In addition, a comparison to older similar Finnish measurements was made with an attempt to analyze the reasons behind differences in the most typical non-process elements, aluminum (Al), silicon (Si), calcium (Ca), phosphorus (P), magnesium (Mg), manganese (Mn), chlorine (Cl), and potassium (K), taking into account the main elements in the white liquor, sodium (Na) and sulfur (S). The extensive laboratory results gained in this study are from seven sampling points at six pulp mills and present analytical data of metal concentrations. The data obtained presents an update to previous NPE studies. The levels found did not statistically differ between North and South Finland. The NPE levels, apart from phosphorus, found in Finnish pulp mills today have not changed considerably compared to the levels in earlier investigations in the 1990s. In the newest data, the phosphorus concentration was consistently higher in the as fired black liquor, electrostatic precipitator (ESP) ash, lime mud, and green liquor than in the previous results. In addition, the levels of Al, Si, Ca, P, and Mg in recovery boiler ESP ash were consistently higher compared to the older results. As the mills start to close their systems more, a stronger accumulation of NPEs can be expected, increasing the likelihood of more operational problems in the process. Further understanding of where the NPEs accumulate and how they can be most effectively removed will be valuable knowledge in the future.
Journal articles
Magazine articles
Dissolution of wood components during hot water extraction of spruce, TAPPI Journal May 2023
ABSTRACT: The purpose of this study was to investigate the autohydrolysis of softwood, which is the main chemical operation in both hot water extraction and steam explosion. Control of the process and monitoring its course were ensured by the careful choice of experimental setup and conditions: a milled spruce material was extracted in a small flow-through reactor to minimize degradation of the dissolved material and to enable analysis of the resulting liquors extracted at selected time points. The obtained liquid and solid fractions were analyzed for sugar composition and acetic acid concentration. The results showed that partially degraded hemicelluloses were extracted; hemicelluloses side chains were cleaved off and detected as monomers, while deacetylation was limited. Chain scissions of cellulose were observed as a result of autohydrolysis.
Journal articles
Optimization of energy efficiency and condensate production in evaporation plants for a modern softwood pulp mill, TAPPI Journal April 2026
ABSTRACT: To meet the need to further improve thermal efficiency and environmental performance of kraft pulp mills, new systems and techniques have been developed within the evaporation plant. This paper describes these novel approaches and how they were implemented in a project completed in 2018 for a new evaporator and condensate treatment system supplied by Valmet at the SCA Östrand market pulp mill in Sweden. This project was part of a stepwise upgrade of the complete mill to increase the production capacity of the mill from 430,000 to 900,000 air-dried metric tons/year (ADt/y). As part of this upgrade, the mill had the objectives to increase the energy efficiency of the pulp mill and to minimize the air emissions as much as possible, the effluent volume, and the water usage in the mill. The mill also wanted to have the disposal of the biosludge in the black liquor, and the production of tall oil from black liquor soap, liquid methanol, and turpentine. This required that the new evaporation and condensate treatment system be very closely integrated into the other process departments of the mill, including integration of the hot weak black liquor flash vapor from the digester directly into the evaporator train and the production of multiple streams of clean evaporation plant condensate at the correct temperature for the bleach plant. Heat and mass balance calculation values, which were found to do very well in predicting the effect on actual mill operation, are also presented in this paper.
Journal articles
Biphasic 1-butanol/water delignification of miscanthus for manufacturing papermaking pulp, TAPPI Journal August 2026
ABSTRACT: Miscanthus has emerged as a promising nonwoody fiber source for papermaking and fiber molding as the world has sought alternatives to wood-based products. A diverse range of chemistries have been explored at the laboratory scale to turn nonwoody biomass into fibers; however, few have been successful at pilot or commercial scales. An emerging organosolv delignification chemistry that has demonstrated previous technical success is butanol/water, having been shown to produce papers with similar properties to other, more conventional chemistries, but offering the benefit of a built-in sugar and lignin coproduct separation. While a range of fiber lengths were achieved (0.45•0.95 mm), addition of sodium hydroxide (NaOH) to the butanol/water delignification chemistry resulted in fiber lengths comparable to commercially available hardwood pulps (0.7•1.0 mm). Lignin concentration was reduced from 19.1 wt% in the raw miscanthus to under 3.5 wt% for most trials. The lowest lignin concentration (2.5 wt%) was achieved at 180°C for 180 min with 50:50 butanol:water and 2 wt% acetic acid. Yet, the high severity of this condition (and similar ones) resulted in a significant truncation of fiber length, which is detrimental for papermaking applications. The highest quality pulp for papermaking was generated at 180°C for 180 min with 50:50 butanol:water and 10 wt% NaOH. This pulp had one of the longest fiber lengths, the highest brightness, and the highest hemicellulose concentration. Thus, butanol/water delignification, especially with NaOH addition, resulted in the successful production of cellulose-rich pulps that have potential in commercial papermaking and fiber molding applications.
Journal articles
Examination of scoring parameters of corrugated fiberboard, TAPPI Journal August 2026
ABSTRACT: One of the less interrogated aspects of corrugated packaging are scoring and scoring profiles, the intentional localized crushing of flutes to accommodate package folding and closure. This study explores the effect of scoring parameters on box compression test strength (BCT) of two balanced corrugated boards. Scoring differences produced BCT that varied by 10% for one board and less for the other board. Parameters from 4-point bending of scored specimens showed some correlation with BCT, while eccentricity and torsion parameters had less correlation. Different scores produced BCT differences that were not strongly predicted by most standard tests in the current study, implying other tests may be needed to examine the actual boundary conditions on a box during compression. In a few cases, aggressive scoring produced cracked score lines, and those containers had lower BCT than containers with uncracked score lines.
Journal articles
Investigating the causes of severe economizer tube thinning in a spent sulfite liquor (SSL) boiler, TAPPI Journal August 2026
ABSTRACT: In this study, the causes of tube thinning in the economizer of an ammonia-based spent sulfite liquor (SSL) boiler in a Canadian pulp mill are investigated. The tube thinning was most severe in the upper tube rows of the lowest economizer sections where the tube surface temperature ranges between about 180°C and 210°C. The location, the temperature range, and the results of a tube failure analysis indicate that some form of corrosion- erosion is the main cause for the tube thinning. The process is likely initiated by the formation of potassium bisulfate in tube deposits. We hypothesize that some areas in the economizer, including gaps in tube shields, have allowed for temporary buildup of deposits that were not fully removed by sootblowing. Potassium bisulfate is highly hygroscopic, so it readily absorbs moisture, forming an acidic solution leading to corrosion. The corrosion products are removed by the erosive effects of high velocity gas movement, causing the tube thinning. The high-speed fluid flow may be a result of sootblower action and/or enhanced flue gas velocity due to channeling. The tube thinning eventually leads to perforation and leakage.
Journal articles
Utilization of inline total dissolved solids measurement system in a pulp mill's brownstock washing line, TAPPI Journal January 2026
ABSTRACT: Efficient washing improves the recovery of sodium (Na) and sulfur (S) cooking chemicals, as well as wood-based dissolved organic material. It also reduces the additional consumption of chemicals in the subsequent bleaching stages. The operation of the brownstock washing of the pulp mill’s fiber line has a significant impact on the mill’s energy economy, material efficiency, and environmental emissions. Process refractometers can be used to measure the total dissolved solids (TDS) from both the washing liquor and the pulp suspension filtrate part directly from pipelines or pipe bypass loops. In addition, by measuring the three or four incoming/outgoing dissolved solids streams to the washers, together with consistencies and flow rate measurements, it is possible to build the real-time effectiveness calculation of the washer(s). In this work, an online efficiency calculation based on TDS measurements was built for a pressure filter after cooking and oxygen (O2) delignification. The washing performance was monitored over a longer period, and stepwise tests were conducted to find the optimal operating mode. The feed and washing consistencies, the washer’s torque, and the washing liquid distributions varied, and the washer’s efficiency values were monitored using realtime measurements. From the long-term trends of the efficiency calculation, process disturbances could be detected, and their causes could be found. Based on the results of the stepwise tests, an optimal operating model for the washer was found. By optimizing the washing consistency, the Y10 washing yield could be increased. More efficient washing with the same or even a smaller amount of washing liquid can relieve the operation of the evaporator, which is often a bottleneck in the mill. The study also found the effect of cooking-related carryover on the operation of the oxygen stage, as well as differences in the washability of softwood and hardwood.
Journal articles
Towards closed water systems in chemical pulp mills: Evaporation of acidic filtrate from ECF bleaching with high chloride content, TAPPI Journal January 2026
ABSTRACT: In modern bioproducts mills utilizing elemental chlorine-free (ECF) bleaching, the bleaching process is the primary effluent source. The pulp bleaching typically generates 10 m³/a.d. metric ton of acidic filtrate. Despite extensive studies on recycling methods, the acidic filtrate is still typically directed to wastewater treatment plants due to the challenges created by its volume and chloride content. Recently, the volume of acidic filtrate has significantly decreased to 5 m³/a.d. metric ton, reducing the capacity required for the recycling process closer to a feasible level. In this study, we investigated recycling of acidic filtrate by evaporation from the D0 stage of a D0-Eop-D1 bleaching sequence. In the mill, hydrochloric acid (HCl) was used for pH control instead of sulfuric acid (H2SO4) due to better control of precipitation. This arrangement substantially changes the composition of the acidic filtrate, increasing the chloride (Cl-) and decreasing the sulfate (SO4 2-) ionic content. For the above reasons, it is necessary to study the effect of evaporation on the quality of the resulting condensate and concentrate. The results provide new information on how to close water loops in a modern bioproducts mill with higher Cl- content as one option. The results show that the evaporation of the high-chlorine D0 filtrate produces a pure condensate with methanol as the main component. Only small amounts of Cl- were observed in the condensate. The majority of chlorine (Cl) compounds remains as dissolved compounds in the evaporated concentrate when the dry solids content of the concentrate is ~10%. The Cl compounds in the concentrate can be converted to sodium chloride (NaCl) by incineration.
Journal articles
Editorial: New research sheds light on critical processes in the recovery cycle, TAPPI Journal July
The chemical recovery cycle has been called the backbone of a kraft pulp mill, making modern paper production both economically and environmentally sustainable. It regenerates pulping chemicals (primarily sodium hydroxide and sodium sulfide) used to separate wood fibers, allowing them to be reused rather than continuously replaced, while also recovering energy by burning the organic components of black liquor to produce steam and electricity that supply much of the mill’s power needs. In addition, the recovery cycle minimizes waste, reduces emissions, and recovers valuable by-products, creating a highly efficient closedloop system. Without this process, chemical costs, energy consumption, and environmental impacts would increase, making large-scale kraft pulping significantly less economical and sustainable.
Journal articles
Alternative disposal methods for pulp mill biosludge
ABSTRACT: The chemical pulp production process produces notable amounts of biosludge, mostly in the wastewater treatment system. Biosludge is a problematic waste stream due to its properties, and recently, its amounts have been on the increase. The most used disposal processes are incineration in a bark boiler or a recovery boiler now that landfilling is no longer permitted by legislation in many countries. Incineration of wet sludges with poor drying characteristics decreases the energy efficiency of the process. Biosludge is typically mixed with black liquor in the evaporation plant before feeding to the recovery boiler. Although the recovery boiler is designed to handle challenging fuels, biosludge disposal requires consideration of its behavior during evaporation and accumulation of non-process elements in the recovery cycle. This study discusses the currently used sludge handling methods and presents two novel methods, hydrothermal carbonization and anaerobic digestion, to convert sludge into a usable form. Production of hydrochar or biogas offers new usage possibilities for biosludge and improves the energy efficiency of the mill when the new methods replace incineration. The processes are still developing, and thus their economic feasibility is uncertain; however, depending on the case details, they can be considered promising alternatives to be implemented in the future.