Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Non-process elements in the recovery cycle of six Finnish kraft pulp mills, TAPPI Journal March 2023
ABSTRACT: In this work, the aim was to study the distribution and accumulation of the non-process elements (NPEs) in the recovery cycle of Finnish pulp mills and look at whether the geographical location (North vs. South) correlates with the current Finnish NPE levels. In addition, a comparison to older similar Finnish measurements was made with an attempt to analyze the reasons behind differences in the most typical non-process elements, aluminum (Al), silicon (Si), calcium (Ca), phosphorus (P), magnesium (Mg), manganese (Mn), chlorine (Cl), and potassium (K), taking into account the main elements in the white liquor, sodium (Na) and sulfur (S). The extensive laboratory results gained in this study are from seven sampling points at six pulp mills and present analytical data of metal concentrations. The data obtained presents an update to previous NPE studies. The levels found did not statistically differ between North and South Finland. The NPE levels, apart from phosphorus, found in Finnish pulp mills today have not changed considerably compared to the levels in earlier investigations in the 1990s. In the newest data, the phosphorus concentration was consistently higher in the as fired black liquor, electrostatic precipitator (ESP) ash, lime mud, and green liquor than in the previous results. In addition, the levels of Al, Si, Ca, P, and Mg in recovery boiler ESP ash were consistently higher compared to the older results. As the mills start to close their systems more, a stronger accumulation of NPEs can be expected, increasing the likelihood of more operational problems in the process. Further understanding of where the NPEs accumulate and how they can be most effectively removed will be valuable knowledge in the future.
Journal articles
Magazine articles
Dissolution of wood components during hot water extraction of spruce, TAPPI Journal May 2023
ABSTRACT: The purpose of this study was to investigate the autohydrolysis of softwood, which is the main chemical operation in both hot water extraction and steam explosion. Control of the process and monitoring its course were ensured by the careful choice of experimental setup and conditions: a milled spruce material was extracted in a small flow-through reactor to minimize degradation of the dissolved material and to enable analysis of the resulting liquors extracted at selected time points. The obtained liquid and solid fractions were analyzed for sugar composition and acetic acid concentration. The results showed that partially degraded hemicelluloses were extracted; hemicelluloses side chains were cleaved off and detected as monomers, while deacetylation was limited. Chain scissions of cellulose were observed as a result of autohydrolysis.
Journal articles
Optimization of energy efficiency and condensate production in evaporation plants for a modern softwood pulp mill, TAPPI Journal April 2026
ABSTRACT: To meet the need to further improve thermal efficiency and environmental performance of kraft pulp mills, new systems and techniques have been developed within the evaporation plant. This paper describes these novel approaches and how they were implemented in a project completed in 2018 for a new evaporator and condensate treatment system supplied by Valmet at the SCA Östrand market pulp mill in Sweden. This project was part of a stepwise upgrade of the complete mill to increase the production capacity of the mill from 430,000 to 900,000 air-dried metric tons/year (ADt/y). As part of this upgrade, the mill had the objectives to increase the energy efficiency of the pulp mill and to minimize the air emissions as much as possible, the effluent volume, and the water usage in the mill. The mill also wanted to have the disposal of the biosludge in the black liquor, and the production of tall oil from black liquor soap, liquid methanol, and turpentine. This required that the new evaporation and condensate treatment system be very closely integrated into the other process departments of the mill, including integration of the hot weak black liquor flash vapor from the digester directly into the evaporator train and the production of multiple streams of clean evaporation plant condensate at the correct temperature for the bleach plant. Heat and mass balance calculation values, which were found to do very well in predicting the effect on actual mill operation, are also presented in this paper.
Journal articles
Biphasic 1-butanol/water delignification of miscanthus for manufacturing papermaking pulp, TAPPI Journal August 2026
ABSTRACT: Miscanthus has emerged as a promising nonwoody fiber source for papermaking and fiber molding as the world has sought alternatives to wood-based products. A diverse range of chemistries have been explored at the laboratory scale to turn nonwoody biomass into fibers; however, few have been successful at pilot or commercial scales. An emerging organosolv delignification chemistry that has demonstrated previous technical success is butanol/water, having been shown to produce papers with similar properties to other, more conventional chemistries, but offering the benefit of a built-in sugar and lignin coproduct separation. While a range of fiber lengths were achieved (0.45•0.95 mm), addition of sodium hydroxide (NaOH) to the butanol/water delignification chemistry resulted in fiber lengths comparable to commercially available hardwood pulps (0.7•1.0 mm). Lignin concentration was reduced from 19.1 wt% in the raw miscanthus to under 3.5 wt% for most trials. The lowest lignin concentration (2.5 wt%) was achieved at 180°C for 180 min with 50:50 butanol:water and 2 wt% acetic acid. Yet, the high severity of this condition (and similar ones) resulted in a significant truncation of fiber length, which is detrimental for papermaking applications. The highest quality pulp for papermaking was generated at 180°C for 180 min with 50:50 butanol:water and 10 wt% NaOH. This pulp had one of the longest fiber lengths, the highest brightness, and the highest hemicellulose concentration. Thus, butanol/water delignification, especially with NaOH addition, resulted in the successful production of cellulose-rich pulps that have potential in commercial papermaking and fiber molding applications.
Journal articles
Examination of scoring parameters of corrugated fiberboard, TAPPI Journal August 2026
ABSTRACT: One of the less interrogated aspects of corrugated packaging are scoring and scoring profiles, the intentional localized crushing of flutes to accommodate package folding and closure. This study explores the effect of scoring parameters on box compression test strength (BCT) of two balanced corrugated boards. Scoring differences produced BCT that varied by 10% for one board and less for the other board. Parameters from 4-point bending of scored specimens showed some correlation with BCT, while eccentricity and torsion parameters had less correlation. Different scores produced BCT differences that were not strongly predicted by most standard tests in the current study, implying other tests may be needed to examine the actual boundary conditions on a box during compression. In a few cases, aggressive scoring produced cracked score lines, and those containers had lower BCT than containers with uncracked score lines.
Journal articles
Investigating the causes of severe economizer tube thinning in a spent sulfite liquor (SSL) boiler, TAPPI Journal August 2026
ABSTRACT: In this study, the causes of tube thinning in the economizer of an ammonia-based spent sulfite liquor (SSL) boiler in a Canadian pulp mill are investigated. The tube thinning was most severe in the upper tube rows of the lowest economizer sections where the tube surface temperature ranges between about 180°C and 210°C. The location, the temperature range, and the results of a tube failure analysis indicate that some form of corrosion- erosion is the main cause for the tube thinning. The process is likely initiated by the formation of potassium bisulfate in tube deposits. We hypothesize that some areas in the economizer, including gaps in tube shields, have allowed for temporary buildup of deposits that were not fully removed by sootblowing. Potassium bisulfate is highly hygroscopic, so it readily absorbs moisture, forming an acidic solution leading to corrosion. The corrosion products are removed by the erosive effects of high velocity gas movement, causing the tube thinning. The high-speed fluid flow may be a result of sootblower action and/or enhanced flue gas velocity due to channeling. The tube thinning eventually leads to perforation and leakage.
Journal articles
Editorial: New research sheds light on critical processes in the recovery cycle, TAPPI Journal July
The chemical recovery cycle has been called the backbone of a kraft pulp mill, making modern paper production both economically and environmentally sustainable. It regenerates pulping chemicals (primarily sodium hydroxide and sodium sulfide) used to separate wood fibers, allowing them to be reused rather than continuously replaced, while also recovering energy by burning the organic components of black liquor to produce steam and electricity that supply much of the mill’s power needs. In addition, the recovery cycle minimizes waste, reduces emissions, and recovers valuable by-products, creating a highly efficient closedloop system. Without this process, chemical costs, energy consumption, and environmental impacts would increase, making large-scale kraft pulping significantly less economical and sustainable.
Journal articles
Alternative disposal methods for pulp mill biosludge
ABSTRACT: The chemical pulp production process produces notable amounts of biosludge, mostly in the wastewater treatment system. Biosludge is a problematic waste stream due to its properties, and recently, its amounts have been on the increase. The most used disposal processes are incineration in a bark boiler or a recovery boiler now that landfilling is no longer permitted by legislation in many countries. Incineration of wet sludges with poor drying characteristics decreases the energy efficiency of the process. Biosludge is typically mixed with black liquor in the evaporation plant before feeding to the recovery boiler. Although the recovery boiler is designed to handle challenging fuels, biosludge disposal requires consideration of its behavior during evaporation and accumulation of non-process elements in the recovery cycle. This study discusses the currently used sludge handling methods and presents two novel methods, hydrothermal carbonization and anaerobic digestion, to convert sludge into a usable form. Production of hydrochar or biogas offers new usage possibilities for biosludge and improves the energy efficiency of the mill when the new methods replace incineration. The processes are still developing, and thus their economic feasibility is uncertain; however, depending on the case details, they can be considered promising alternatives to be implemented in the future.
Journal articles
Modern NCG practice, TAPPI Journal July 2026
ABSTRACT: New innovations have been put in operation for collection and handling systems of noncondensable gases (NCGs) in modern kraft pulp mills. This work investigates technologies in new pulp mills that aim to achieve the benefits of odor-free processes while enhancing chemical circulation within the mill. It describes and discusses both past and current systems for collecting and handling NCGs. The mills studied have designed and implemented their NCG systems within the past 10 to 15 years. New innovations have emerged, offering promising methods to further reduce occasional sulfurous odor emissions from the kraft process. These methods explore pretreatment and sulfuric gas stream reuse options in process units where these gases are generated or during the transportation of these side streams to their final destruction site. Using modern practices outlined in this paper, malodorous gases can be collected to the extent that a kraft pulp mill is essentially odor-free pending operator errors or major equipment malfunctions. One of the difficult aspects is that NCG systems in kraft mills are often designed case-by-case, as well as by various equipment vendors and with varying numbers of destruction sites. The actual detailed design depends on the chosen layout, process configuration depending on individual equipment purchased, and even on the design practices of individual suppliers.
Journal articles
Effects of calcium on sodium salt scaling with the presence of resin acids and fatty acids, TAPPI Journal June 2026
ABSTRACT: Reintroducing tall oil soap or its related products into high dry solids black liquor has been found to reduce sodium salt scaling in falling film evaporators. Aside from resin acids and fatty acids, which are the likely scale inhibitors, calcium is reintroduced into black liquor because of the relatively high calcium content of tall oil soap. One concern is that this increase in calcium content might lead to the formation of additional calcium and sodium scales in evaporators. In this work, we investigated the relationship among trace amounts of calcium, sodium salts, resin acids, and fatty acids in a controlled system using a model salt solution and a benchtop setup. We studied the effects of the calcium carbonate addition and calcium carbonate scales on sodium salt scaling in the presence of resin acids and fatty acids. We found that some calcium carbonate is incorporated in the precipitated sodium crystals, and the suspended sodium crystals become larger and more compact with increasing calcium carbonate concentration. Experiments in the benchtop setup show that precipitating calcium carbonate scale on the heat exchanger does not lead to a higher rate of sodium salt scaling. The solubility of calcium carbonate is not affected by the addition of resin acids and fatty acids. These findings indicate that the reduction in sodium salt scaling through the addition of tall oil soap is primarily related to resin acids and fatty acids, rather than to calcium or to interactions between calcium and mixtures of resin and fatty acids.