Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Effects of carboxymethyl starch as a papermaking additive, TAPPI Journal February 2024
ABSTRACT: Carboxymethyl starch (CMS) is a bio-based, anionic polymer that has potential as part of a dry-strength additive program for papermaking. Due to its negative charge, its effects can be expected to depend on its interactions with various cationic agents. In this work, the effects of CMS were observed following its sequential addition after one of three selected cationic strength agents at different dosage levels. In selected tests, the furnish was pretreated at the 1% level by a dispersant, sodium polyacrylate, which might represent a high level of anionic contaminants in a paper mill system. Laboratory tests were conducted to show the effects on dewatering, fine-particle retention, and flocculation. These tests were supplemented with measurements of charge demand, zeta potential, and handsheet properties. Sequential addition of cationic glyoxylated acrylamide copolymers (gPAM) and CMS were found to strongly promote dewatering. Two gPAM products and a poly(vinylamine) product in sequential addition with CMS were very effective for promoting fine-particle retention. These same sequential treatments of the stock contributed to moderate fiber flocculation, though severe flocculation was caused by further treatment of the furnish with colloidal silica. Handsheet strength results were mixed. In the default recycled copy paper furnish, the average breaking length for the sheets made with cationic additives followed by CMS was not greatly different from the blank condition. Superior strength resulted when the default furnish was treated with a dispersant alone. When the dispersant-contaminated furnish was treated with the same combinations of cationic additives and CMS, the strength returned to the baseline achieved in the absence of the dispersant. The results were discussed in terms of the charged character of the different additives and their interactions not only with the fiber surfaces but also with each other.
Journal articles
Magazine articles
Effects of hydrodynamic shear during formation of paper sheets with the addition of nanofibrillated cellulose, cationic starch, and cationic retention aid, TAPPI Journal September 2024
ABSTRACT: Laboratory tests were conducted to evaluate effects of hydrodynamic shear levels on papermaking process variables and paper handsheet properties. The furnish was from 100% recycled copy paper, to which was added nanofibrillated cellulose (NFC) at the 5% level following its optional pretreatment with cationic starch. A cationic copolymer of acrylamide (cPAM) was used as the retention aid. Different levels of hydrodynamic shear were applied both after mixing the NFC with the cationic starch (pre-shearing) or after all the furnish components had been combined (final shearing). The presence or absence of pre-shearing was found to have little effect on the measured outcomes. By contrast, increasing final shear hurt filler retention and made the resulting paper more uniform. However, the final shear level did not have a significant effect on the tensile strength of the resulting handsheets. Medium-charge density cationic starch, used in pretreating the NFC, consistently gave greater strength in comparison to a high-charge cationic starch. The significance of these findings is that though the relatively high hydrodynamic shear levels associated with modern paper machines can have some beneficial effects, they do not necessarily overcome all challenges associated with wet-end addition of nanocellulose in combination with other additives.
Journal articles
Magazine articles
Kinetics of sulfur dioxide-alcohol-water (SAW) pulping of su
Kinetics of sulfur dioxide-alcohol-water (SAW) pulping of sugarcane straw (SCS), TAPPI JOURNAL June 2017
Journal articles
Magazine articles
Guest Editorial: Still working (overtime): Life-saving nonwovens and continued innovation, TAPPI Journal August 2021
ABSTRACT: Recently, the United States federal government has recommended the need for a booster shot to combat COVID-19, highlighting the highly contagious nature of its Delta variant. This variant is surging in countries as far apart as Thailand, Brazil, and the United States. While the availability of the vaccine is not an issue in the United States, African, Latin American, and South Asian countries are in dire need of the vaccine. This scenario necessitates the need for continued safety measures. Among the recommended safety measures, use of face masks has been proven to be effective. Recent analysis showed that two-thirds of the 32 states in the United States with face mask mandates found them helpful for lowering infection rates.
Journal articles
Magazine articles
Numerical analysis of the impact of rotor and screen hole plate design on the performance of a vertical pulper, TAPPI Journal April 2025
ABSTRACT: The dissolving of mechanical pulp is one of the most important process steps in stock preparation, since pulping occurs at the very beginning of the papermaking process. Efficient mixing of the pulp in a short amount of time is essential to achieve high furnish volume flow rates. The design of the rotor, as well as the pulper vat and inserts, significantly affects the overall performance of the pulper, such as mixing efficiency and power demand. Using advanced numerical methods such as computational fluid dynamics (CFD) can accelerate the development process. The CFD simulations allow for detailed analysis of flow phenomena, making it possible to study a real-size machine numerically. This approach is particularly advantageous because it can reduce the need for timeconsuming and costly experiments associated with scaling up test rigs. In this study, we compared two different rotor designs utilized in a vertical pulper and evaluated the numerical results with experimental data. Rotor A is designed for low turbulence and low power demand, while rotor B is designed for high turbulence with high power demand. The CFD results showed good agreement with the experimental measurements. We investigated how the rotor design influences the free fluid surface and the mixing efficiency. Our study also highlights the differences in results depending on whether water or furnish is simulated, which exhibit Newtonian or, respectively, non-Newtonian fluid behavior. Additionally, a detailed numerical investigation of various screen hole plate designs revealed that the newly developed hole design significantly reduces pressure loss compared to a standard drilled hole. This outcome was consistent for both types of fluids investigated: water and furnish.
Journal articles
Magazine articles
Characterization of the redispersibility of cellulose nanocrystals by particle size analysis using dynamic light scattering, TAPPI Journal April 2019
ABSTRACT: Cellulose nanocrystals (CNCs), which are derived from the most abundant and inexhaustible natural polymer, cellulose, have received significant interest owing to their mechanical, optical, chemical, and rheological properties. In order to transport CNC products conveniently and efficiently, they are ideally dried and stored as pow-ders using freeze-drying or spray-drying technologies. The redispersibility of CNC powders is quite important for their end use; hence, a convenient method is required to characterize the redispersibility of CNC powders. In this paper, the possibility of characterizing the redispersibility of CNC powders by particle size analysis using dynamic light scattering (DLS) was investigated by comparing the results from transmission electron microscopy (TEM) and DLS. The particle size obtained with DLS approximately matched that obtained with TEM. Compared with TEM, DLS is a quick and convenient method to measure the particle size distribution of CNCs in water. Two kinds of dispersing methods, sonication and high-speed shearing, and two kinds of CNCs prepared by different methods, sulfuric acid hydrolysis and the TEMPO (2,2,6,6-tetramethylpiperidine-1-oxyl) oxidization method, were used to study the redis-persibility of CNCs. Sonication was more efficient than the high-speed shearing method for nanoscale dispersion of CNC powders in water. CNCs prepared by sulfuric acid hydrolysis could be more easily redispersed in water than those prepared by TEMPO oxidation.
Journal articles
Magazine articles
Priorities for development of standard test methods to support the commercialization of cellulose nanomaterials, TAPPI Journal April 2019
ABSTRACT: With the growing number of producers and users of cellulose nanomaterials (CNMs), there is an increasing need to develop standard test methods to control production and quality of CNMs. In 2014, a Task Group was formed within the ISO Technical Committee 6 Paper, board and pulps to begin addressing the need for standards. This Task Group, TG 1, was tasked with reviewing existing standards and identifying the need for additional standards to characterize CNMs.In March 2018, TG 1 launched a survey to ask CNM producers around the world about the importance of having standard procedures to measure and quantify a variety of CNM properties, both physical and chemical. Producers were asked to identify the type(s) of CNM they produced and their scale of production, and to rank the properties for which they felt standard test methods were most important. In this paper, we summarize the survey responses and identify those properties of highest interest for producers of both cellulose nanocrystals (CNCs) and cellulose nano- and microfibril-based materials (CNFs/CMFs). Properties of importance can be divided into three broad groups: i) a standard has either been developed or is under develop-ment, ii) a currently used standard could be adapted for use with CNMs, or iii) no standard is currently available and further R&D and consultation with industry is needed before a suitable and well-validated standard can be developed. The paper also examines the challenges of developing new standard methods for some of the key properties—as well as the feasibility and limitations of adapting exiting standards—to CNMs.
Journal articles
Magazine articles
Fundamental molecular characterization and comparison of the O, D0, and E stage effluents from hardwood pulp bleaching, TAPPI Journal 2019
ABSTRACT: The present study characterized effluents from the O, D0, and E stages using nuclear magnetic reso-nance (NMR) and gel permeation chromatography (GPC) techniques to better understand the chemical nature of the dissolved organics formed from the bleaching of a high-yield hardwood kraft pulp. Understanding the structures and molecular weight distribution of these organics is the first step in developing methods to mitigate these contam-inates in the discharged effluents. The results indicated that the molecular weight distribution (MWD) of the dis-solved organics from oxygen delignification effluent is broader than those from D0 and E stage effluents. In addition, the O stage filtrate contained considerable amounts of lignin and xylan fragments, which showed its efficiency in removing such materials. The effluent from the D0 stage contained a lower amount of high molecular weight frag-ments and a higher amount of low molecular weight fragments versus the O-stage filtrate. Aromatic structures were nearly absent in the D0 stage filtrate, but the degraded organic material, presumably from oxidized lignin, contained olefinic (C=C) and carbonyl (C=O) functional groups. Furthermore, higher molecular weight fragments were detected in the E-stage effluent, presumably due to the extensive solubilization and removal of the oxidized lignin generated from the D0 pulp.
Journal articles
Magazine articles
Wet-end addition of nanofibrillated cellulose pretreated with cationic starch to achieve paper strength with less refining and higher bulk, TAPPI JOURNAL July 2018
Wet-end addition of nanofibrillated cellulose pretreated with cationic starch to achieve paper strength with less refining and higher bulk, TAPPI JOURNAL July 2018
Journal articles
Magazine articles
Furnishing autohydrolyzed poplar weakly alkaline P-RC APMP to make lightweight coated base paper, TAPPI Journal February 2022
ABSTRACT: This work investigated the effects of autohydrolysis pretreatment severity on poplar (Populus tomentosa Carr.) woodchips used to make a type of high-yield pulp (HYP) known as preconditioning followed by refiner chemical treatment, alkaline peroxide mechanical pulp (P-RC APMP). It also investigated the ratios for partially replacing sodium hydroxide (NaOH) with magnesium oxide (MgO) in the high-consistency (HC) retention stage of the P-RC APMP process on the obtained HYP’s properties. The results show that the pretreatment severity of autohydrolysis at combined hydrolysis factor (CHF) = 10.77 and the 50 wt% ratio for partially substituting NaOH with MgO were the optimum conditions for making light-weight coated (LWC) base paper. Compared to the conventional P-RC APMP, the optimized P-RC APMP had similar bulk and higher tensile, burst, and tear indices, as well as opacity, but a slightly lower ISO brightness. When the optimized P-RC APMP and commercial softwood bleached sulfate pulp (SBKP) were blended to make LWC base paper, the most favorable pulp furnish was comprised of 50% optimized P-RC APMP and 50% commercial SBKP. The obtained LWC base paper handsheet had better bulk, and its other properties could also meet the require-ments of LWC base paper.