Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Effects of calcium on sodium salt scaling with the presence of resin acids and fatty acids, TAPPI Journal June 2026
ABSTRACT: Reintroducing tall oil soap or its related products into high dry solids black liquor has been found to reduce sodium salt scaling in falling film evaporators. Aside from resin acids and fatty acids, which are the likely scale inhibitors, calcium is reintroduced into black liquor because of the relatively high calcium content of tall oil soap. One concern is that this increase in calcium content might lead to the formation of additional calcium and sodium scales in evaporators. In this work, we investigated the relationship among trace amounts of calcium, sodium salts, resin acids, and fatty acids in a controlled system using a model salt solution and a benchtop setup. We studied the effects of the calcium carbonate addition and calcium carbonate scales on sodium salt scaling in the presence of resin acids and fatty acids. We found that some calcium carbonate is incorporated in the precipitated sodium crystals, and the suspended sodium crystals become larger and more compact with increasing calcium carbonate concentration. Experiments in the benchtop setup show that precipitating calcium carbonate scale on the heat exchanger does not lead to a higher rate of sodium salt scaling. The solubility of calcium carbonate is not affected by the addition of resin acids and fatty acids. These findings indicate that the reduction in sodium salt scaling through the addition of tall oil soap is primarily related to resin acids and fatty acids, rather than to calcium or to interactions between calcium and mixtures of resin and fatty acids.
Journal articles
Optimization of optical coverage of board surfaces with assessment of light scattering and absorption using mineral as a coating component, TAPPI Journal June 2026
ABSTRACT: One of the primary functions of mineral inclusion into paper or paperboard is to improve the optical performance of the substrate. A coating may be applied to a sheet in order to cover a dark base, to improve the sheet opacity, to give the correct smoothness and gloss, or to give a suitable surface on which to print. The brightness of a pigment has long been used as a guide for pigment choice in paper and board. However, the measured paper brightness is a function of color and light absorption (K) of the coating and base and the light scattering (S) within the sheet resulting from interfaces with different refractive index. The optical performance can be quantified by measuring the S&K coefficients as described by the Kubelka-Munk model/theory in a filled or coated paper sheet. In coating, this is often assessed as a function of coat weight, and the corresponding physical sheet properties are assessed at the same time; for example, the correct gloss, smoothness, point-to-point uniformity, and printability. The optical performance in the sheet is often not directly related to the pigment brightness, but is largely a function of the particle packing within the sheet and coating layer. In the first and second main sections of this work, respectively, we show how S&K calculations from the Kubelka- Munk equations can be used in coated sheets to determine the optical performance and how this can be used as a predictive tool for the final sheet performance. This is presented for base sheets with different starting brightness. The third section of this work focuses on how mineral combinations in coatings can be used to improve the light scattering and consequently the optical performance of the board. We include theoretical considerations and then finally share a case study for improvement on the optical properties of recycled board.
Journal articles
Preparation of a vegan leather from mycelium with papermaking method, TAPPI Journal June 2026
ABSTRACT: With growing concern over the environmental impacts of both natural leather and conventional synthetic leathers, the development of sustainable and eco-friendly leather alternatives has become an urgent research priority. In this study, an innovative wet papermaking strategy is proposed to fabricate continuous, homogeneous mycelial sheets from chitin-rich fungal mycelium, mimicking the matrix structure of genuine leather. These mycelial sheets were chemically modified to meet the performance requirements of leather foam layers. Subsequently, the modified mycelial sheets were combined with a substrate fabric to produce a novel mycelium-based leather composite (myco-paper leather) that achieves an excellent balance of mechanical properties and tactile qualities. Experimental results demonstrate that the mycelium-sheet-based leather substitute exhibits remarkable mechanical performance, with a tensile strength of approximately 45 MPa and an elongation at break of about 10.5%. After lamination with the substrate fabric, the composite material shows a tear strength of approximately 16 N, along with a desirable hand feel and surface texture. Following tannic acid tanning, the mycelial sheets also exhibit significant antimicrobial and antifungal properties, forming an inhibition zone of approximately 2 mm against Staphylococcus aureus. Through reinforcement with plant fibers, the developed material attains both strength and flexibility, indicating that the wet papermaking of mycelial sheets is a feasible and scalable approach for producing sustainable leather alternatives. This work not only employs a simple and mature papermaking process to process fungal mycelium but also provides a new conceptual and practical foundation for the large-scale production of bio-based leather substitutes. The findings have significant implications for advancing a low-carbon, sustainable leather industry.
Journal articles
Investigation of the factors contributing to malodorous gases emission during secondary fiber reuse, TAPPI Journal June 2026
ABSTRACT: Malodorous gases are commonly produced during secondary fiber reuse, which is harmful to human health and causes environmental pollution. This paper investigated the influence of fiber type and concentration, temperature, and whitewater concentration on the malodorous gases. The results indicated that, in pulp prepared with fresh water, bleached hardwood kraft pulp (LBKP) did not produce malodorous gases after standing for five days. In contrast, the secondary fiber began to release substantial amounts of total volatile organic compounds (TVOC) on the third day and hydrogen sulfide (H2S) and ammonia (NH3) on the sixth day, and black substances began to appear in the pulp, which proved that the microorganisms began to proliferate. With the increase of the secondary fiber concentration, the release amounts of TVOC, H2S, and NH3 gradually rose, along with the black substances in the pulp. With increased temperature, the release of TVOC increased steadily, while the release of H2S and NH3 reached the maximum at about 45°C, and then began to decline. The decrease of the pulp freeness accelerated the generation of the malodorous gases, but the total release amounts of TVOC, H2S, and NH3 were basically the same. With the increase of white water concentration, the release of TVOC, H2S, and NH3 increased rapidly. When the white water/fresh water was 20 mL/80 mL, the slurry changed from pale yellow to aterrimus on the sixth day. Therefore, microorganisms in the secondary fiber caused pulp deterioration, while white water was the main reason for generating a large amount of malodorous gases.
Journal articles
The effects of coated magazines on deinking of newsprint after pulping and flotation, TAPPI JOURNAL, December 1998, Vol. 81(12)
The effects of coated magazines on deinking of newsprint after pulping and flotation, TAPPI JOURNAL, December 1998, Vol. 81(12)
Journal articles
Hardwood pulping kinetics of bulk and residual phases, TAPPI JOURNAL October 2015
Hardwood pulping kinetics of bulk and residual phases, TAPPI JOURNAL October 2015
Journal articles
Quantification of lignin-carbohydrate complexes in hardwood pulps, Part 2: Effects of bleaching chemicals, TAPPI JOURNAL October 2015
Quantification of lignin-carbohydrate complexes in hardwood pulps, Part 2: Effects of bleaching chemicals, TAPPI JOURNAL October 2015
Journal articles
Magazine articles
Extension of a steady-state chlorine dioxide brightening model for Z-ECF bleaching of softwood kraft pulps, TAPPI Journal March 2021
ABSTRACT: Earlier studies developed a steady-state model to predict the brightness and/or bleach consumption during the chlorine dioxide brightening (D1) of softwood pulps produced by conventional elemental-chlorine-free (ECF) sequences. This model relates the chlorine dioxide consumed to the brightness gains predicated upon an asymptotic D1 brightness limit, an incoming D1 pulp brightness, and an equation parameter (ß11). The current investigation examines the application of this model to ECF sequences that use ozone delignification (Z-ECF). Literature D1 data from various Z-ECF bleaching studies, which investigated OZ, OD0/Z, and OZ/D0 delignification, were fitted to the model. The ß11 parameter was found to be linearly correlated to the entering kappa number. Interestingly, this linear relationship was found to be identical to the relationships observed when modeling the D1 stage for conventional ECF and chlorine-based bleach sequences. Subtle differences in D1 brightening response in the model among the various bleach sequences are reflected by incoming pulp brightness (at the same kappa number). The current model is used to illustrate how alterations to Z-ECF delignification affect D1 brightening and chlorine dioxide consumption.
Journal articles
Magazine articles
Development of converging-diverging multi-jet nozzles for molten smelt shattering in kraft recovery boilers, TAPPI Journal March 2021
ABSTRACT: The effective shattering of molten smelt is highly desired in recovery boiler systems. Ideally, shatter jet nozzle designs should: i) generate high shattering energy; ii) create a wide coverage; and iii) minimize steam consumption. This study proposes a novel converging-diverging multi-jet nozzle design to achieve these goals. A laboratory setup was established, and the nozzle performance was evaluated by generating jet pressure profiles from the measurement of a pitot tube array. The results show that the shatter jet strength is greater with a large throat diameter, high inlet pressure, and a short distance between the nozzle exit and impingement position. Increasing the number of orifices generates a wider jet coverage, and the distance between the orifices should be limited to avoid the formation of a low-pressure region between the orifices. The study also demonstrates that an optimized converging-diverging multi-jet nozzle significantly outperformed a conventional shatter jet nozzle by achieving higher energy and wider coverage while consuming less steam.
Journal articles
Magazine articles
Black liquor evaporator upgrades— life cycle cost analysis, TAPPI Journal March 2021
ABSTRACT: Black liquor evaporation is generally the most energy intensive unit operation in a pulp and paper manufacturing facility. The black liquor evaporators can represent a third or more of the total mill steam usage, followed by the paper machine and digester. Evaporator steam economy is defined as the unit mass of steam required to evaporate a unit mass of water from black liquor (i.e., lb/lb or kg/kg.) The economy is determined by the number of effects in an evaporator train and the system configuration. Older systems use four to six effects, most of which are the long tube vertical rising film type. Newer systems may be designed with seven or even eight effects using falling film and forced circulation crystallization technology for high product solids. The median age of all North American evaporator systems is 44 years. Roughly 25% of the current North American operating systems are 54 years or older. Older systems require more periodic maintenance and have a higher risk of unplanned downtime. Also, older systems have chronic issues with persistent liquor and vapor leaks, shell wall thinning, corrosion, and plugged tubes. Often these issues worsen to the point of requiring rebuild or replacement. When considering the age, technology, and lower efficiency of older systems, a major rebuild or new system may be warranted. The intent of this paper is to review the current state of black liquor evaporator systems in North America and present a basic method for determining whether a major rebuild or new installation is warrant-ed using total life cycle cost analysis (LCCA).