Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Focusing on the future of paper machines, TAPPI JOURNAL, January 1998, Vol. 81(1)
Focusing on the future of paper machines, TAPPI JOURNAL, January 1998, Vol. 81(1)
Journal articles
Influence of coating composition on web release in high speed film transfer coating, TAPPI JOURNAL, January 1998, Vol. 81(1)
Influence of coating composition on web release in high speed film transfer coating, TAPPI JOURNAL, January 1998, Vol. 81(1)
Journal articles
The role of analytical winding dynamics in winder design, TAPPI JOURNAL, January 1998, Vol. 81(1)
The role of analytical winding dynamics in winder design, TAPPI JOURNAL, January 1998, Vol. 81(1)
Journal articles
Theory and techniques of electrostatic charging of melt-blown nonwoven webs, TAPPI JOURNAL, January 1998, Vol. 81(1)
Theory and techniques of electrostatic charging of melt-blown nonwoven webs, TAPPI JOURNAL, January 1998, Vol. 81(1)
Journal articles
Tools of the hedging trade, TAPPI JOURNAL, January 1998, Vol
Tools of the hedging trade, TAPPI JOURNAL, January 1998, Vol. 81(1)
Journal articles
The special problems of pulp and paper mill equipment, TAPPI
The special problems of pulp and paper mill equipment, TAPPI JOURNAL, August 1991, Vol. 74(8)
Journal articles
89APR177
MD microstriations in paper: a two-sided shrinkage phenomenon?, TAPPI JOURNAL April 1989
Journal articles
Analysis of wrinkle formation and propagation during paperboard deep drawing, TAPPI Journal October 2026
ABSTRACT: Paper-based packaging is becoming increasingly important as a sustainable alternative to plastics. Among forming processes, deep drawing is particularly promising due to its high cost-effectiveness, short processing times, and suitability for large-scale production. A major challenge, however, lies in the formation of wrinkles, which impair the visual quality, functional performance, and dimensional stability of the packaging, thereby affecting subsequent processes such as filling, printing, and sealing. This study focuses on analyzing the occurrence and propagation of wrinkles during the deep drawing of paperbased materials to derive fundamental insights and strategies for prevention. The wrinkles arise from tangential compressive stresses in the flange and the material’s limited thickening, leading to local stability failures once a critical stress threshold is exceeded. A combined approach of experimental investigations, numerical simulations, and analytical considerations was used to examine a rotationally symmetrical part. A transparent die enabled spatial observation of wrinkle initiation and growth. First, wrinkles were found to typically initiate in the cross direction (CD), while most wrinkles develop in the machine direction (MD). By comparing analytically and numerically determined stress distributions, the mechanisms of wrinkle formation can be understood both locally and temporally, thereby enabling the prediction of wrinkle occurrence.
Journal articles
Water and grease resistance of paperboard coated with long chain cellulose fatty acid esters using electrostatic powder coating, TAPPI Journal April 2026
ABSTRACT: Fiber-based materials used for foodservice, takeaway, and other packaging applications must typically provide water and grease resistance. Simultaneously, there is growing interest towards bio-based and renewable barrier coatings. In this study we applied thermoplastic long chain fatty acid cellulose esters onto paperboard using electrostatic powder coating to create barrier properties of interest. Electrostatic powder coating provides a water-free process to tackle moisture-induced quality issues and to provide an even coating layer. Cellulose octanoate and palmitate esters were produced in pilot scale. These were ground into fine particles using liquid nitrogen and applied onto paperboard sheets using an electrostatic powder gun. The loosely packed coatings were fixed and fused onto the paperboard by hot pressing. We characterized the coated sheets for coating thickness, contact angles with water, water absorption, grease resistance (KIT), and olive oil barrier. Two commercial polyethylene powders were used as references. Our results indicated that the long chain cellulose fatty acid ester coatings were thermoplastic and hydrophobic with contact angles above 100°. Water absorption was similar to the reference coatings. While grease resistance was lower than with the references, the cellulose ester coatings slowed down diffusion of olive oil through the paperboard. Cellulose octanoate ester with a lower melt viscosity already provided smooth coatings after the initial hot pressing step, while in most cases, the second post hot pressing step further improved the barrier properties.
Journal articles
Optimization of energy efficiency and condensate production in evaporation plants for a modern softwood pulp mill, TAPPI Journal April 2026
ABSTRACT: To meet the need to further improve thermal efficiency and environmental performance of kraft pulp mills, new systems and techniques have been developed within the evaporation plant. This paper describes these novel approaches and how they were implemented in a project completed in 2018 for a new evaporator and condensate treatment system supplied by Valmet at the SCA Östrand market pulp mill in Sweden. This project was part of a stepwise upgrade of the complete mill to increase the production capacity of the mill from 430,000 to 900,000 air-dried metric tons/year (ADt/y). As part of this upgrade, the mill had the objectives to increase the energy efficiency of the pulp mill and to minimize the air emissions as much as possible, the effluent volume, and the water usage in the mill. The mill also wanted to have the disposal of the biosludge in the black liquor, and the production of tall oil from black liquor soap, liquid methanol, and turpentine. This required that the new evaporation and condensate treatment system be very closely integrated into the other process departments of the mill, including integration of the hot weak black liquor flash vapor from the digester directly into the evaporator train and the production of multiple streams of clean evaporation plant condensate at the correct temperature for the bleach plant. Heat and mass balance calculation values, which were found to do very well in predicting the effect on actual mill operation, are also presented in this paper.