Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Magazine articles
Z-direction chemical analysis for new application methods, TAPPI Journal January 2023
ABSTRACT: In conventional wet-end chemical addition during paper production, chemical distribution through the z-direction of the sheet is usually not considered an important characteristic. With a nontraditional chemical dosing approach, such as foam-assisted additive addition, the chemistry can appear at different concentrations throughout the sheet, typically in a z-direction gradient. To fully understand the strength properties of the sheet, it is helpful to view or quantify the chemical distribution through the sheet in the z-direction. One qualitative method uses a dye technique along with confocal laser scanning microscopy to generate an image where the relative chemical concentration can be observed. A quantitative method involves compiling nitrogen analyses of layered subsections of the sheet into a composite graph of relative chemical concentration vs. the z-direction of the sheet. Chemical distribution analysis can be paired with traditional z-direction strength tests, such as Scott bond and z-direction tensile, to help one understand and improve the chemical addition process and its effects.
Journal articles
Magazine articles
Pareto-based design of experiments for identifying and comparing optimum sealing parameters of heat sealing applications in packaging machines, TAPPI Journal June 2023
ABSTRACT: Sealing is one of the most important process steps in industrial packaging, because the sealed seam is the most sensitive section of a package in terms of quality. For this reason, a major focus in flexible packaging is the sealing process, and among this, heat sealing is the most frequently used technology. In detail, applications of heat sealing processes are confronted with four conflicting objectives: increasing seam quality, reducing dwell time, reducing sealing temperature, and increasing process robustness towards varying conditions. Typical problems, such as identification of the optimum process parameters or selection of the most appropriate packaging film, are subject to these conflicting objectives.This paper presents a recently published design of experiments for characterizing and comparing heat sealing properties of packaging films based on a multi-objective optimization algorithm. The approach provides easy-to-read charts showing all optimum sealing parameters with regard to the four essential objectives of heat sealing: seam quality, dwell time, sealing temperature, and process robustness. Three case studies show exemplary applications of the new approach: 1) analyzing transport damages of beverage powder packages; 2) identifying and comparing optimum sealing parameter of a standard, mono-material, and fiber based packaging film regarding tightness and visual properties of the produced sachets; and 3) analyzing the effect of additional aluminum layers on sealing characteristics regarding hot-tack.The new design of experiments may provide the basis of a standard test method for the identification of optimal sealing parameters in the heat sealing processes.
Journal articles
Magazine articles
Recovery boiler back-end heat recovery, TAPPI Journal March 2023
ABSTRACT: Sustainability and efficient use of resources are becoming increasingly important aspects in the operation of all industries. Recently, some biomass-fired boilers have been equipped with increasingly complex condensing back-end heat recovery solutions, sometimes also using heat pumps to upgrade the low-grade heat. In kraft recovery boilers, however, scrubbers are still mainly for gas cleaning, with only simple heat recovery solutions. In this paper, we use process simulation software to study the potential to improve the power generation and energy efficiency by applying condensing back-end heat recovery on a recovery boiler. Different configurations are considered, including heat pumps. Potential streams to serve as heat sinks are considered and evaluated. Lowering the recovery boiler flue gas temperature to approximately 65°C significantly decreases the flue gas losses. The heat can be recovered as hot water, which is used to partially replace low-pressure (LP) steam, making more steam available for the condensing steam turbine portion for increased power generation. The results indicate that in a simple condensing plant, some 1%•4% additional electricity could be generated. In a Nordic mill that provides district heating, even more additional electricity generation, up to 6%, could be achieved. Provided the availability of sufficient low-temperature heat sinks to use the recovered heat, as well as sufficient condensing turbine swallowing capacity to utilize the LP steam, the use of scrubbing and possibly upgrading the heat using heat pumps appears potentially useful.
Journal articles
Magazine articles
Non-process elements in the recovery cycle of six Finnish kraft pulp mills, TAPPI Journal March 2023
ABSTRACT: In this work, the aim was to study the distribution and accumulation of the non-process elements (NPEs) in the recovery cycle of Finnish pulp mills and look at whether the geographical location (North vs. South) correlates with the current Finnish NPE levels. In addition, a comparison to older similar Finnish measurements was made with an attempt to analyze the reasons behind differences in the most typical non-process elements, aluminum (Al), silicon (Si), calcium (Ca), phosphorus (P), magnesium (Mg), manganese (Mn), chlorine (Cl), and potassium (K), taking into account the main elements in the white liquor, sodium (Na) and sulfur (S). The extensive laboratory results gained in this study are from seven sampling points at six pulp mills and present analytical data of metal concentrations. The data obtained presents an update to previous NPE studies. The levels found did not statistically differ between North and South Finland. The NPE levels, apart from phosphorus, found in Finnish pulp mills today have not changed considerably compared to the levels in earlier investigations in the 1990s. In the newest data, the phosphorus concentration was consistently higher in the as fired black liquor, electrostatic precipitator (ESP) ash, lime mud, and green liquor than in the previous results. In addition, the levels of Al, Si, Ca, P, and Mg in recovery boiler ESP ash were consistently higher compared to the older results. As the mills start to close their systems more, a stronger accumulation of NPEs can be expected, increasing the likelihood of more operational problems in the process. Further understanding of where the NPEs accumulate and how they can be most effectively removed will be valuable knowledge in the future.
Journal articles
Magazine articles
Paper bending stiffness and web tension measurement from a running web using a vacuum and computer imaging, TAPPI Journal May 2023
ABSTRACT: A novel method for measuring the bending stiffness of paper online during manufacturing is introduced. The method uses photometric stereo imaging to detect the shape of the deflection surface caused by a controllable pressure difference over the paper’s surfaces. The hardware for the measurement is based on a combination of two existing sensors, which has accelerated and facilitated the development of the implementation. The deflection and loads are tied together by the governing differential equation for the bending of an orthotropic elastic plate with selected simplifications. An approach to resolve material parameters and in-plane loads without knowledge of traditional boundary conditions is suggested. The presented method was tested in a paper mill during manufacturing. For bending stiffnesses measured online, correlation coefficients 0.88 and 0.92 were obtained compared to state-of-the-art laboratory measurements. However, the results gained from a moving web are noisy and the data requires correction of the slope and an off-set. Although several issues remain to be resolved before the method can be considered as an accurate measurement for industrial use, the theoretical background, the performance of online implementation, and the results are promising. Possible causes for the observed discrepancies and the future development of the method are discussed.
Journal articles
Comparison of the application of polysaccharide-based barrier coatings on paper using film press and spray coating, TAPPI Journal January 2025
The growing demand for sustainable packaging has spurred research into biopolymer-based solutions and their application to paper substrates. This study compares the application of low solids, high viscous aqueous solutions of alginate and chitosan on two different paper substrates using a laboratory film press coater and a purpose-built spray coating unit, with a focus on barrier performance and practical industry considerations. Key parameters investigated are air flow rate, water vapor transmission rate, and grease resistance. Results showed that due to the low solids content of the applied biopolymer solutions, film press coating required a double-layer application for coat weights exceeding 4 g/m², making it less viable for industrial application. In contrast, spray coating allowed for higher application weights in a single step. The barrier properties of spray coated samples, compared to film press coatings, varied with the paper substrate: spray coating performed better on one substrate and worse on the other. Contact angle measurement of the substrates suggested that spray coating is more suitable for a more hydrophilic substrate because of improved surface wetting. The study also identified issues with drying conditions and pinholes affecting the quality of spray coated samples, indicating a need for further research to optimize these parameters.
Journal articles
Water-based adhesive penetration into paperboard and coated paperboard, TAPPI Journal January 2025
The setting of water-based adhesives in contact with paperboard is important in the production of boxes and other packaging, but the topic has received little attention in the literature. The penetration of the adhesive into the paper surface is important to get good bond strength through mechanical interlocking. The influence of the process conditions and the paper properties on this penetration is lacking. A water-based adhesive was applied to an uncoated and coated paperboard. The coating layer had two latex levels. Samples were characterized in terms of air permeability, void fraction, average pore size, and coat weight. The adhesive was applied to the samples in a mechanical press, squeezing a drop between two samples. The penetration of the adhesive was characterized with a silicone oil absorption method that measured the decrease in pore volume after the adhesive had been applied to approximate the pore volume taken up by the adhesive. The bond strength was measured with a peeling test. The penetration depth into uncoated paper did not depend on the application method parameters such as pressing time, pressure, or initial solids of the adhesive. The penetration depth ranged from 35•40 mm. The penetration into 10 pph latex content coated paper was similar to the uncoated samples, but reduced penetration was observed into the 40 pph latex content coatings. The results were compared to the limiting amount of adhesive that was obtained from the weight gain of the samples and to a simple model that is based on flow in porous media. Peel tests revealed that good penetration was needed, as well as a strong coating layer to obtain high peel forces.
Journal articles
Effect of xylan on the mechanical performance of softwood kraft pulp 2D papers and 3D foams, TAPPI Journal March 2025
ABSTRACT: Pulp fibers are paramount in paper products and have lately seen emerging use in fiber foams. Xylan, an integral component in pulp fibers, is known to contribute to paper strength, but its effect on the strength of pulp fiber foams remains less explored. In this study, we investigate the role of xylan in both 2D handsheets and 3D foams. For a softwood kraft pulp, we enzymatically removed 1% from pulp fibers and added 3% xylan to them by adsorption, corresponding to approximately a decrease of a tenth and an increase of a third of the total xylan content. The mechanical properties of 2D fiber networks, i.e., handsheets, made using the xylan-enriched pulp improved, particularly regarding tensile strength and Young’s modulus; however, the decrease in mechanical properties of handsheets made from enzymatically- treated xylan-depleted pulp was more pronounced. In 3D networks • pulp fiber foams, much less fiber-fiber contacts formed, and thus the mechanical properties were not as much influenced by removal of xylan. Furthermore, the presence of the required surfactant on the fibers, acting as debonding agent, overshadows any positive effect xylan might have on fiber-fiber bonding. We propose that the improved mechanical properties for the sheets result from a combination of an increased number of fiber-fiber bonds and higher sheet density, while the deterioration in mechanical properties of handsheets comprising enzymatically-treated fibers is caused by the opposite effect.
Journal articles
Predictive advisory solutions for chemistry management, control, and optimization, TAPPI Journal March 2025
ABSTRACT: Process runnability and end-product quality in paper and board making are often connected to chemistry. Typically, monitoring of the chemistry status is based on a few laboratory measurements and a limited number of online specific chemistry-related measurements. Therefore, mill personnel do not have real-time transparency of the chemistry related phenomena, which can cause production instability, including deposition, higher chemical consumption, quality issues in the end-product and runnability problems. Machine learning techniques have been used to establish soft sensor models and to detect abnormalities. Furthermore, these soft sensors prove to be most useful when combined with expert-driven interpretation. This study is aimed at utilizing a hybrid solution comprising chemistry and physics models and machine learning models for stabilizing chemistry-related processes in paper and board production. The principal idea is to combine chemistry/physics models and machine learning models in a fashion close to white box modeling. A cornerstone in the approach is to formulate explanations of the findings from the models; that is, to explain in plain text what the findings mean and how operational changes can mitigate the identified risks. The approach has been demonstrated for several different applications, including deposit control in the wet end, both raw water treatment and usage, and wastewater treatment. This approach provides mill personnel with knowledge of identified phenomena and recommendations on how to stabilize chemistry-related processes. Instead of using close to black box machine learning models, a hybrid solution including chemistry/physics models can enhance the performance of artificial intelligence (AI) deployed systems. A successful way of gaining the trust from mill personnel is by creating a plain text explanation of the findings from the hybrid models. The correlation between the likelihood of a phenomena and disturbance and the explanations are derived and validated by application and chemistry and physics experts.
Journal articles
Colloidal silica and its effects during formation of paper sheets in the presence of nanofibrillated cellulose, cationic starch, and cationic acrylamide copolymer, TAPPI Journal May 2025
ABSTRACT: This work considered effects of colloidal silica addition during laboratory preparation of paper sheets containing nanofibrillated cellulose (NFC) that had been pretreated with cationic starch. The emphasis was on process performance issues, including dewatering rates, fine particle retention, and the extent of fiber flocculation. In addition, micrographs were obtained to show what was happening to the NFC upon treatments with cationic starch and subsequent application of hydrodynamic shear. Contrasting results were obtained, depending on the charge density of the cationic starch. Pretreatment of the NFC with a high charge density cationic starch (degree of substitution 0.2) resulted in strong interactions with the colloidal silica, enhancing the dewatering rate and contributing to fine-particle retention. The medium charge cationic starch pretreatment led to effects suggesting a bridging mechanism of action, and subsequent colloidal silica had no significant effect on dewatering. Treatment of that system with a high level of colloidal silica (0.2%) resulted in lower retention. In general, the final colloidal silica treatments tended to decrease the level of flocculation in the suspensions, giving more uniform handsheets. Mechanisms, some of them related to the clustering and dispersion of cationic starch-treated NFC, were proposed to account for the observed effects.