Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Investigation of the factors contributing to malodorous gases emission during secondary fiber reuse, TAPPI Journal June 2026
ABSTRACT: Malodorous gases are commonly produced during secondary fiber reuse, which is harmful to human health and causes environmental pollution. This paper investigated the influence of fiber type and concentration, temperature, and whitewater concentration on the malodorous gases. The results indicated that, in pulp prepared with fresh water, bleached hardwood kraft pulp (LBKP) did not produce malodorous gases after standing for five days. In contrast, the secondary fiber began to release substantial amounts of total volatile organic compounds (TVOC) on the third day and hydrogen sulfide (H2S) and ammonia (NH3) on the sixth day, and black substances began to appear in the pulp, which proved that the microorganisms began to proliferate. With the increase of the secondary fiber concentration, the release amounts of TVOC, H2S, and NH3 gradually rose, along with the black substances in the pulp. With increased temperature, the release of TVOC increased steadily, while the release of H2S and NH3 reached the maximum at about 45°C, and then began to decline. The decrease of the pulp freeness accelerated the generation of the malodorous gases, but the total release amounts of TVOC, H2S, and NH3 were basically the same. With the increase of white water concentration, the release of TVOC, H2S, and NH3 increased rapidly. When the white water/fresh water was 20 mL/80 mL, the slurry changed from pale yellow to aterrimus on the sixth day. Therefore, microorganisms in the secondary fiber caused pulp deterioration, while white water was the main reason for generating a large amount of malodorous gases.
Journal articles
Permeability simulation for filled paper based on three-dimensional structural model developed by X-ray computed tomography scanning, TAPPI Journal March 2026
ABSTRACT: In this study, an in-depth exploration of filled paper was conducted to understand its structural and permeability characteristics. Cotton linter pulp and precipitated calcium carbonate (PCC) filler were utilized to prepare pure fiber paper, and PCC1 and PCC2 filled papers with different filler particle sizes. Then, the pore structure parameters of paper samples were characterized by mercury intrusion porosimetry, and the X-ray computed tomography (X-CT) scanning was carried out. Subsequently, the 3D microstructures were established based on the X-CT slice images, and the filler characteristic parameters and filler 3D distribution were quantitatively analyzed. Finally, permeation simulations in the thickness and horizontal directions were performed. The findings indicate that filling changes the paper porosity, and the pore tortuosity varies with direction. The estimated pore•throat radius distribution shows specific patterns for different papers. The fillers have different distribution characteristics in the paper samples. Moreover, the paper permeability differs with direction, with smallsized filler having a significant impact on fluid penetration in the thickness direction. Overall, this study provides an effective method for investigating internal paper filler and its distribution, which contributes to the understanding of paper structure•performance relationships.
Journal articles
Moisture performance of silica-paper hybrids in the hygroscopic range, TAPPI Journal March 2026
ABSTRACT: Vapor retarders, crucial in building constructions, are traditionally made from plastic-based materials, raising environmental concerns due to the use of fossil materials. This study explores the potential of functionalized papers, particularly silica-paper hybrids, as sustainable alternatives. This work delves into the moisture properties of sol-gel coated linter papers, considering the water vapor permeability and physisorption behavior following DIN EN ISO 12572 and DIN EN ISO 12571. The study addresses hysteresis, noting the lower hysteresis of mesoporous coatings in comparison to dense coatings and implying benefits in moisture release. Findings underscore the need for a nuanced understanding of coating characteristics and their impact on sorption. In order to better assess the relationship between the coating content of the papers and their specific sorption properties, further investigations, such as the measurement of specific surface properties (e.g., specific surface area), are required. The findings of the water vapor diffusion resistance measurement study demonstrate a correlation between the observed resistance and the vapor levels. The results show that the water vapor diffusion resistance is elevated at lower vapor levels when compared to higher levels. This particular material behavior is typically employed within the construction industry for the utilization of moisture-variable water vapor retarders. The silica-paper hybrids exhibit a response that indicates the potential for advancement into a moisture-variable water vapor barrier.
Journal articles
Effects of in-plane straining on the out-of-plane delamination properties of paperboard, TAPPI Journal March 2026
ABSTRACT: Delamination strength is an essential property for the creasing and folding operations of paperboard into boxes. Due to fixation during creasing, the paperboard suffers in-plane straining. In the present study, we aim to increase our understanding of how in-plane straining affects the delamination properties of paperboard. Samples of paperboard were first strained in in-plane tensile loading, both in the machine-direction and in the cross-direction. Afterward, the paperboard is loaded in the out-of-plane (ZD) direction. Three different grades of commercial paperboard from two major manufacturers were tested in a climate-controlled lab. The results showed similar results for all grades of paperboard, with the delamination strength and the out-of-plane stiffness decreasing virtually linearly with pre-straining. With about 5% plastic in-plane straining, the strength was reduced by about 20% and the stiffness decreased by more than 50% for all grades of paperboard. Normalizing the strength and the stiffness with their values without pre-straining reveals virtually the same relation for all grades of paperboard. If proven to be a general result, this will prove valuable in reducing the demand for experiments.
Journal articles
Magazine articles
Review of coating cracking and barrier integrity on paperboard substrates, TAPPI Journal November 2022
ABSTRACT: Barrier packaging formats are major growth areas for the pulp and paper industry. It is technically challenging to maintain barrier properties during converting and end-use applications. Improved manufacturing capabilities and coating formulation knowledge will help maintain barrier integrity and enable growth of barrier products in challenging applications. These improvements will accelerate product development and commercialization, and allow faster response to product performance issues such as cracking. The literature on coating cracking provides knowledge mostly on the effects of coating formulations and to a lesser extent on substrate effects. Despite a large number of publications dedicated to coating failures, the approach to improve coating cracking remains empirical, and the transferability between studies and to real life applications has not been well established. Model development that successfully predicts commercial performance is in its infancy. However, some of these simplified models do a fairly good job predicting experimental data. The current work reviews the state of understanding as regards coating and barrier cracking and highlights the need for more research on cracking and barrier integrity.
Journal articles
Magazine articles
Modeling the influence of rheology on smooth rod coating systems, TAPPI Journal November 2022
ABSTRACT: Rod coating methods are of interest for the application of barrier coatings, especially at off-line facilities that may run at moderate speeds and narrow web widths. At lower line speeds and lower coating solids, it is difficult to achieve good coat weight control because of poor loading of the rod. While there is extensive literature available about blade and roll coating, there seems to be less reported on the rod loading of smooth rods to obtain various coat weights. Much of the work is around metering rods working on applicator rolls at high speeds that are associated with the metered size press, with a focus on ribbing instabilities. This work employs a simplified model, neglecting some complex features of rubber deformation and film split, to estimate the influence of the process parameters such as speed, rod diameter, viscosity, and rod loading on the coat weight obtained. As found in practice, at low speed and low viscosities, the coat weight-load curve is steep, leading to poor control of the coat weight and coat weight uniformity. If the viscosity is increased, the curve is modified, and control is possible with rod loading in a normal range. For shear thinning fluids described by the Carreau model, the power law index and other parameters need to be in the correct range to obtain the desired effect. Modeling predictions show a steeper dependence of coat weight with rod pressure when compared to pilot coater data. This may be caused by missing details in the mechanical loading of the rod related to tube pressure or from neglecting the impact of filter cake formation of the applied coating in the model.
Journal articles
Magazine articles
Coatings for sustainable paper-based flexible packaging: Barrier properties and processability, TAPPI Journal November 2022
ABSTRACT: In this study, the use of waterborne barrier dispersions from trademarked BLUEWAVE Mechanical Dispersion Technology as thin coatings for paper-based flexible packaging was investigated. Prototypes were designed and examined for their performance in process, rheology, barrier, heat-seal/hot-tack, and coefficient of friction (CoF). Compositional details such as the type and amount of base resins and dispersants were found to significantly impact performances and were key to the development of new prototypes that deliver the performance profiles for implementation in paper-based flexible packaging applications.
Journal articles
Magazine articles
Novel test method for measuring defects in barrier coatings, TAPPI Journal November 2022
ABSTRACT: In the last several years, activity to develop water-based barrier coatings (WBBCs) that meet challenging packaging performance requirements has increased dramatically. Cellulose-based packaging solutions can provide a more sustainable packaging option for replacing single-use plastic-based options like extrusion-based and laminated materials. An advantage of WBBCs is the opportunity to reduce the coating thickness applied, as long as the barrier requirements can be met. A challenge that must be overcome is the ability to maintain a defect and pin-hole-free coating layer after coating and drying to retain the barrier performance. Many formulation and coating parameters can affect the barrier coating layer quality; however, methods for detecting more subtle differences in these types of studies are not widely available. Work was carried out to develop a quantitative technique for detecting and measuring the quantity and size of defects in the barrier coating layer. A test method has been developed using a combination of dyed oil and image analysis to be able to characterize the imperfections in the coating surface. The use of dyed oil serves two purposes. First, it better simulates the types of materials, in this case, oils and grease, for which the barrier coating is expected to hold out. Second, it also provides contrast between the coating and failure points for testing. An image analysis technique is employed to characterize the number and size of the imperfections. For the former, it reduces the testing time required if a quality control or laboratory technician counts the dots. For the latter, it assists with judgment on the source of the root cause of the imperfection, such as base sheet defects, coating dispersion issues, or perhaps micro-blisters in the coating, as some examples.To show the benefit of this technique, several pilot coating studies were designed to see if the new technique could be utilized to detect differences in WBBC performance. Both process and chemical variables were evaluated. With refinement, it is believed this technique can be utilized in development work, as well as for a potential quality control technique for manufacturing of coated paper and paperboard products.
Journal articles
Magazine articles
Effectiveness of masks in the suppression of COVID-19 cases during the ongoing pandemic in India, TAPPI Journal October 2022
ABSTRACT: Perhaps the worst predicament faced by humanity in the twenty-first century is the COVID-19 pandemic, which is caused by the SARS-CoV-2 virus. Most parts of the world, including India, went into lockdowns for some period because of the massive increase in cases throughout 2020. Face masks became an important counter-measure for protecting the populace, health professionals, and medics, particularly during the period prior to the mass availability of vaccines. This study intends to evaluate the effectiveness of face masks in limiting the spread of the virus. The data for the number of COVID-19 cases was analyzed from January 1, 2022 to May 31, 2022, using Python programming. This timeframe involved face mask mandates and no mask requirement, and hence was considered to be ideal for analyzing the usefulness of face masks. A decline in cases during the mandate was observed, while the opposite occurred without the mandate. The outcome of the research showed that face masks are effective additional measures against the spread of SARS-CoV-2. This study elevates the value of personal protective equipment (PPE), such as face masks, made with nonwovens and other fabrics, as lifesavers in the case of airborne diseases such as COVID-19 and other pulmonary disorders.
Journal articles
Magazine articles
Utilization of palm fiber as papermaking materials: Microscopic structure and chemical pulping, TAPPI Journal October 2022
ABSTRACT: The microscopic structure and pulping properties of palm fiber were explored. Soda cooking and sulfate cooking were conducted and compared in terms of physical strength of the obtained pulps. Sulfate pulp showed better performance than soda pulp, as indicated by the 23% higher tensile index, 49% higher tear index, and 36% higher burst index. To further elevate physical strength, long fibered pulp (LFP), namely commercial softwood sulfate pulp, was mixed with sulfate pulp of palm fiber at levels from 20% to 50%. At the blend level of 50%, tensile index of 52.13 Nœm/g, tear index of 15.63 mNœm2/g, and burst index of 3.42 kPaœm2/g were attained. The lignin in spent liquor from pulping was isolated and characterized. Soda lignin of palm fiber was mainly composed of guaiacyl and syringyl units, and showed weight-average molecular weight of 3616 g/mol.