Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Deinking of newspaper assisted by steam explosion, TAPPI JOURNAL, December 2000, Vol. 83(12)
Deinking of newspaper assisted by steam explosion, TAPPI JOURNAL, December 2000, Vol. 83(12)
Journal articles
Energy marketing offered as new cost-control option, TAPPI JOURNAL, January 1998, Vol. 81(1)
Energy marketing offered as new cost-control option, TAPPI JOURNAL, January 1998, Vol. 81(1)
Journal articles
Industry characteristics and investment decisions: an alternative approach to pulp and paper production, TAPPI JOURNAL, January 1998, Vol. 81(1)
Industry characteristics and investment decisions: an alternative approach to pulp and paper production, TAPPI JOURNAL, January 1998, Vol. 81(1)
Journal articles
On management: Does the pulp and paper industry have to lose the race?, TAPPI JOURNAL, January 1998, Vol. 81(1)
On management: does the pulp and paper industry have to lose the race?, TAPPI JOURNAL, January 1998, Vol. 81(1)
Journal articles
Third-party financing of pulp and paper mill steam, power, and utility sssets, TAPPI JOURNAL, January 1998, Vol. 81(1)
Third-party financing of pulp and paper mill steam, power, and utility sssets, TAPPI JOURNAL, January 1998, Vol. 81(1)
Journal articles
Editor's Notes: Ready for a Test Drive, TAPPI JOURNAL, Novem
Editor's Notes: Ready for a Test Drive, TAPPI JOURNAL, November, 2006
Journal articles
Evaluation of Various Mechanical Pulping Processes for Mature and Juvenile Loblolly Pine in Lightweight Coated Paper, TAPPI JOURNAL March 2009
Evaluation of Various Mechanical Pulping Processes for Mature and Juvenile Loblolly Pine in Lightweight Coated Paper, TAPPI JOURNAL March 2009
Journal articles
Prediction of the Solubility of Recovery Boiler Precipitator Ash, TAPPI JOURNAL May 2009
Prediction of the Solubility of Recovery Boiler Precipitator Ash, TAPPI JOURNAL May 2009
Journal articles
Magazine articles
Lignin-based resins for kraft paper applications, TAPPI Journal November 2019
ABSTRACT: We investigated miscanthus (MS) and willow (W) lignin-furfural based resins as potential reinforce-ment agents on softwood and hardwood kraft paper. These resins might be sustainable alternatives to the commercial phenolformaldehyde (PF) resins. Phenol is a petrochemical product and formaldehyde has been classified as a carcinogen by the U.S. Environmental Protection Agency. The lignin used in this study was derived from hot water extraction (160ºC, 2 h) of MS and W biomass, and may be considered sulfur-free. These biorefinery lignins were characterized for their chemical composition and inherent properties via wet chemistry and instrumental techniques. The resin blends (MS-resin and W-resin) were characterized for their molecular weight, thermal behavior, and mechanical properties. Mechanical properties were measured by the resin’s ability to reinforce softwood and hard-wood kraft papers. The effect of adding hexamethylenetetramine (HMTA), a curing agent, to the resin was also examined. Mixtures of PF and lignin-based resins were investigated to further explore ways to reduce use of non-renewables, phenol, and carcinogenic formaldehyde. The results show that lignin-based resins have the potential to replace PF resins in kraft paper applications. For softwood paper, the highest strength was achieved using W-resin, without HMTA (2.5 times greater than PF with HMTA). For hardwood paper, MS-resin with HMTA gave the highest strength (2.3 times higher than PF with HMTA). The lignin-based resins, without HMTA, also yielded mechanical properties comparable to PF with HMTA.
Journal articles
Magazine articles
Application of ATR-IR measurements to predict the deinking efficiency of UV-cured inks, TAPPI Journal January 2022
ABSTRACT: In recent years, ultraviolet (UV)-curable ink has been developed and widely used in various printing applications. However, using UV-printed products (UV prints) in recovered paper recycling causes end-product dirt specks and quality issues. A new method was developed that can distinguish UV prints from other prints by means of attenuated total reflectance infrared (ATR-IR) spectroscopy. Application of this method could allow more efficient use of UV prints as raw materials for paper recycling.First, a mill trial was performed using UV prints alone as raw materials in a deinked pulp (DIP) process. Second, test prints were made with four types of UV inks: a conventional UV ink and three different highly-sensitive UV inks. Each print sample had four levels of four-color ink coverage patterns (100%, 75%, 50%, and 25%). Next, deinkability of all prints was evaluated by laboratory experiments. Finally, each print was measured using the ATR-IR method, and the relationship between the IR spectra and deinkability was investigated. Mill trial results showed that UV prints caused more than 20 times as many dirt specks as those printed with conventional oil-based ink. There were variations in recycling performance among UV prints taken from bales used for the mill trial. Lab tests clearly revealed that not all UV-printed products lead to dirt specks. In order to clarify the factors that affected deinkability of UV prints, the print samples were investigated by lab experiments. Key findings from lab experiments include: œ The number of dirt specks larger than 250 µm in diameter increased as the ink coverage increased. œ Higher ink coverage area showed stronger intensity of ATR-IR spectral bands associated with inks. These results indicate that deinkability of UV prints could be predicted by analysis of ATR-IR spectra. œ Finally, the method was applied for assessment of recovered paper from commercial printing presses. It was confirmed that this method made it possible to distinguish easily deinkable UV prints from other UV prints. Based on these findings, we concluded that the ATR-IR method is applicable for inspection of incoming recovered paper.