Search

Suzano Pulp Plant to Set World Standard for Efficiency, Sustainability, Paper360º September/October 2022

National Labs Work to Make the Bioeconomy a Reality, Paper360º September/October 2022

Reach the Perfect Temperature with Regular Heating System Maintenance, Paper360º September/October 2022

Three Benefits of NIR Technology, Paper360º September/October 2022

TAPPI Journal Summaries, Paper360º September/October 2022

TAPPI Journal Summaries, Paper360º September/October 2022

´Carbon Will be a Lightning Rod’, Paper360º September/October 2022

Effects of agitator blade scaling on mixing in dissolving tanks, TAPPI Journal April 2022

ABSTRACT: Hard calcium carbonate scale often forms on the agitators in smelt dissolving tanks. The effects of this scale on mixing are not well understood. While mixing in tanks has often been modeled in the literature, there have been no studies involving agitator scaling. To better understand the impact of agitator scaling on hydrodynamics and tank concentrations, a steady state, three-dimensional (3D) model has been developed for a smelt dissolving tank at a kraft pulp mill. In this work, four cases are compared: an agitator with no scaling, mild scaling, moderate scaling, and extreme scaling. The extreme scaling case is representative of scale buildup on a dissolving tank agitator that was significant enough that the agitator had to be stopped and cleaned. The reduction in the agitator fluid jet velocity is relatively small for the mild and moderate scaling cases, but it becomes more significant for the extreme scaling case, for which the results indicate that the mixing of the smelt with the weak wash is likely poor and that there would thus be a risk of smelt pooling.

Comparative study of guar gum and its cationic derivatives as pre-flocculating polymers for PCC fillers in papermaking applications, TAPPI Journal April 2022

ABSTRACT: In this work, gums from guar seeds were evaluated as a potential precipitated calcium carbonate (PCC) filler pre-flocculant to induce functional filler in papermaking applications. In recent years, guar has been conidered one of the promising wet-end additives due to its abundance, rich source of hemicellulose content, and bio-degradability. However, application of guar gum in filler pretreatment methods for producing high ash paper has scarcely been reported. In this paper, the flocculating ability of three types of guar gum was established with charge analysis and turbidity (NTU) of the system at 1% and 5% for each gum: native gum (NG) having a degree of substitution (DS) of 0, and cationic gums having a DS value of 0.07 (CL) and 0.15 (CH). It was interesting to observe that even at a 5% dose of G, the charge density of PCC did not deviate much from the initial values. The system carried a weak negativeharge, resulting in an unstable colloidal suspension that led to PCC-PCC particle bridging. On the other hand, the operative mechanism of CL and CH during adsorption and PCC flocculation was predicted to be charge neutralization and electrostatic-patch formation, accompanied by particle bridging. Note that CL, with a maximum 47.5% eduction in residual turbidity of PCC at a 1% dose, was much more efficient in doing so than the other two gums; NG had a 40% maximum reduction in residual turbidity at a 5% dose and CH had a maximum 30% reduction at a 1% ose. Later on, floc formation and structure were correlated with optical and field emission scanning electron microscopy (FE-SEM) images. In the next set of trials, paper properties were determined by varying the different gum dosages from 0.2% to 5% at a constant dose of 20% filler. It is also noteworthy to mention that with 1% CL (low DS) dose, PCC retention increased by 39%, which also enhanced the tensile, tear, burst, and opacity properties by 11%, 19%, 5%, and 4.4%, respectively, without significantly affecting the bulk properties. Further, wide-angle X-ray diffraction (XRD) analysis nd Fourier transform infrared (FTIR) analysis revealed that pre-flocculating PCC with a 1% gum dose did not induce any change in crystalline transformation. Based on observation, it was found that cationic gums with low DS values re a better choice for maximizing the strength of paper while maintaining bulk and high opacity when pre-flocculaion is adopted to increase the filler retention in paper.

Editorial: Impacts from using recycled pizza boxes in furnish: TAPPI Journal’s runner-up to 2021 Best Research Paper, TAPPI Journal August 2022

ABSTRACT: The runner-up to the 2021 TAPPI Journal Best Research Paper was “Incorporation of post-consumer pizza boxes in the recover Fiber Stream: Impact of grease on finished product quality."

Edge crush testing methods and box compression modeling, TAPPI Journal August 2022

ABSTRACT: While multiple test procedures have been developed to assess the inherent compressive strength of corrugated materials (edge crush test, ECT), limited work has explored the appropriateness of each in the context of box compression modeling. This study incorporates a variety of real-world samples, highlighting the varying challenges different ECT methods face in measuring the intrinsic compressive resistance of combined corrugated board. We examine each of these methods as inputs for different types of models, as well as discuss the propagation of measurement variation through the modeling effort. By highlighting the cases in which a given ECT method no longer proves to be an optimal parameter in box compression strength modeling, we explore how we might better measure this material property.