Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
Improved barrier performance with microfibrillated cellulose, TAPPI Journal March 2025
ABSTRACT: In this work, the impact of microfibrillated cellulose (MFC) on the properties of water-based barrier coatings intended for food packaging have been explored. Commercially available MFC was used for improving the rheology and water retention of three different commercially available dispersion coatings (acrylic, styrene acrylic, and polylactic acid). Coatings were applied by rod to paper, and barrier properties were tested by measuring air permeability and water barrier properties. Results clearly showed that addition of MFC to water-based dispersion coatings improved the barrier performance of the final coatings.
Journal articles
Using multi-method analysis to identify challenging paper machine deposits and defects, TAPPI Journal March 2025
ABSTRACT: Based on its speed and versatility, Fourier transform infrared (FTIR) spectroscopy is the industry’s common starting point for analysis of a paper machine deposit or defect sample. However, certain contaminants and papermaking process additives cannot be precisely identified solely by infrared spectral interpretation. This lack of specificity could lead to a misinterpretation of the composition of the deposit or defect. A multi-method analysis uses data from two or more analytical techniques, including FTIR spectroscopy, microbiological staining/phase contrast microscopy, pyrolysis-gas chromatography/mass spectrometry (Pyro-GC/MS), and scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDX), to produce a more specific assessment of a sample’s composition. This paper discusses the use of a multi-method analysis in deposit and defect analysis and presents several case studies that demonstrate how this comprehensive approach can often produce an interpretation result of greater conviction and value to the papermaker.
Journal articles
Application of AI-based approach to control the papermaking process, TAPPI Journal March 2025
ABSTRACT: This paper explores AI’s role in revolutionizing the pulp and paper industry, and specifically in predicting wet tensile strength (WTS) for specialty-grade papers. Leveraging eLIXA technology, a 90-day study achieved a 15% reduction in chemical dosage and an 80% decrease in wet tensile standard deviation. The real-time dosage prediction led to optimizing the wet strength resin (WSR) consumption and improved process reliability. The self-learning models exhibited adaptability to changing variables, ensuring their robustness. Overall, this study highlights AI’s transformative impact on efficiency, cost savings, and product quality within the dynamic landscape of papermaking. The approach used for wet strength optimization has been used to optimize other aspects of pulp and paper production.
Journal articles
Pilot-made, highly extensible paper for dry 3D forming, TAPPI Journal May 2025
Cellulose fiber-based packaging materials must perform well in demanding three dimensional (3D) forming process conditions. On the other hand, the development of manufacturing concepts is required for improved competitiveness of bio-based materials. This study covers some key factors that influence the extensibility of cellulose fiber-based structures and presents a pilot-scale development study of a 3D formable material concept. Bleached softwood kraft (BSK) pulp from a Nordic pulp mill was used in the pilot trials. Cellulose-based webs were formed using water-laid and foam-laid web forming using a pilot paper machine. For the water-laid forming, the BSK pulp was refined by applying a high consistency (HC) phase at over 40% consistency, followed by a low consistency (LC) refining at 4% consistency. The BSK pulp was refined for the foam-laid forming by only applying lowconsistency refining. In the foam-laid web forming, anionic sodium dodecyl sulfate (SDS), two foamable latexes, and polyvinyl alcohol (PVA) were used as foaming agents. The pilot rolls were dried at a separate steam cylinder dryer pilot and compacted in-plane in the machine direction (MD) at a separate pilot machine. Tensile properties of the treated paper webs were measured and evaluated with respect to achieved web shrinkage. The same dimensional contraction brought by shrinkage was almost strained out in tensile testing. The results indicated that the shrinkage that occurred by drying and in-plane compaction depended on the pulp furnish. The water-laid material achieved about 30% elongation, whereas the foam-laid material achieved significantly above 50% elongation. The 3D forming performance of the dry materials was tested using fixed and sliding blank methods. The dry paper sheets performed well enough in 3D forming for application to many consumer package applications according to their extensibility.
Journal articles
Paper strength factors in systems with nanofibrillated cellulose, cationic starch, colloidal silica, cationic acrylamide copolymer, and hydrodynamic shear, TAPPI Journal May 2025
ABSTRACT: Laboratory paper sheets were formed by first pretreating nanofibrillated cellulose (NFC) with cationic starch at the 5% level by mass. The treated NFC was then added to stock prepared from 100% recycled copy paper. The combined furnish was next optionally treated with a cationic retention aid (cPAM, 0.1%) and then colloidal silica (0.1% or 0.2%). Vacuum dewatering, fine-particle retention, and several paper properties were studied as a function of the colloidal silica level (zero, 1%, and 2%) and at different levels of shear stress applied just before forming the sheets. Dewatering and strength results were generally more favorable when using a medium charge cationic starch (~ 0.03 degree of substitution, DS) to pretreat the NFC rather than a high charge density cationic starch (~ 0.2 DS). In each case, the dewatering was further enhanced by subsequent treatments by cPAM (0.1% on whole furnish solids) and then even more with the final addition of colloidal silica (0.1% and 0.2% levels compared). However, the colloidal silica additions progressively hurt the tensile strength of the paper, especially in the case of the high charge cationic starch and at the higher level of colloidal silica. Though the dewatering performance was favorable, in such cases, the paper strength was not improved compared to paper made without any NFC. The fact that the systems involving cPAM treatment, and especially those involving both cPAM and colloidal silica, tended to reduce the resulting paper’s tensile strength supports a mechanism in which the additives result in the clustering of the NFC, possibly in multiparticle bunches. Evidence suggests that such bunches of clustered NFC particles, which are difficult to redisperse even at levels of hydrodynamic shear present in high-speed paper machine systems, are resistant to full integration into the sheet structure as the paper is being formed.
Journal articles
Research on an energy model for X-ray measurement of paper ash content using COMSOL, TAPPI Journal May 2025
ABSTRACT: Ash content is one of the critical quality parameters in papermaking production. Traditional 55Fe radioactive sources used for online ash content measurement have a short lifespan and high costs, while offline methods such as the combustion method or chemical analysis are time-consuming. Using an X-ray tube as the radiation source, continuous X-ray measurement offers advantages such as being rapid, non-destructive, and cost-effective. In this study, COMSOL software was employed to simulate the measurement process and establish an energy attenuation model for X-ray measurement of paper ash content. The model simulates the energy attenuation of X-rays before and after transmission through four materials: calcium carbonate (CaCO3), titanium dioxide (TiO2), wood-based plant fibers, and paper samples filled with CaCO3. The absorption coefficients of paper samples with varying ash content were investigated using the model and compared with experimental results obtained from continuous X-ray measurements. The results indicate that the proposed energy simulation model can reduce the measurement error of paper ash content by 1%, significantly enhancing the reliability and accuracy of ash content measurement.
Journal articles
Magazine articles
Boiler retrofit improves efficiency and increases biomass firing rates, TAPPI Journal March 2021
ABSTRACT: Domtar’s fluff pulp mill in Plymouth, NC, USA, operates two biomass/hog fuel fired boilers (HFBs). For energy consolidation and reliability improvement, Domtar wanted to decommission the No. 1 HFB and refurbish/retrofit the No. 2 HFB. The No. 2 HFB was designed to burn pulverized coal and/or biomass on a traveling grate. The steaming capacity was 500,000 lb/h from coal and 400,000 lb/h from biomass. However, it had never sustained this design biomass steaming rate. As the sole power boiler, the No. 2 HFB would need to sustain 400,000 lb/h of biomass steam during peak loads. An extensive evaluation by a combustion and boiler technologies supplier was undertaken. The evaluation involved field testing, analysis, and computational fluid dynamics (CFD) modeling, and it identified several bottle-necks and deficiencies to achieving the No. 2 HFB’s biomass steam goal. These bottlenecks included an inadequate combustion system; insufficient heat capture; excessive combustion air temperature; inadequate sweetwater con-denser (SWC) capacity; and limited induced draft fan capacity.To address the identified deficiencies, various upgrades were engineered and implemented. These upgrades included modern pneumatic fuel distributors; a modern sidewall, interlaced overfire air (OFA) system; a new, larger economizer; modified feedwater piping to increase SWC capacity; replacement of the scrubber with a dry electrostatic precipitator; and upgraded boiler controls.With the deployment of these upgrades, the No. 2 HFB achieved the targeted biomass steaming rate of 400,000 lb/h, along with lowered stack gas and combustion air temperatures. All mandated emissions limit tests at 500,000 lb/h of steam with 400,000 lb/h of biomass steam were passed, and Domtar reports a 10% reduction in fuel firing rates, which represents significant fuel savings. In addition, the mill was able to decommission the No. 1 HFB, which has substantially lowered operating and maintenance costs.
Journal articles
Magazine articles
Tetraethyl orthosilicate-containing dispersion coating — water vapor and liquid water barrier properties, TAPPI Journal September 2021
ABSTRACT: An aqueous styrene-butadiene latex dispersion coating containing in-situ processed tetraethyl orthosilicate (TEOS) applied on paperboard demonstrated improved water barrier performance. Coatings containing TEOS equivalent to 0.8% silicon dioxide (SiO2; dry basis) exhibited water vapor performance of < 25 g/m2/day (23°C, 50% relative humidity [RH]) and liquid water barrier performance Cobb 1800 s of < 6 g/m2, when applied as a single-layer 18 g/m2 coating. Cobb 1800 s barrier performance was still good (< 11 g/m2) at coat weights of 7•10 g/m2. The use of filler materials such as kaolin improved the vapor barrier properties of the coating, but this was not critical to the liquid water barrier properties.
Journal articles
Magazine articles
Commercially relevant water vapor barrier properties of high amylose starch acetates: Fact or fiction?, TAPPI Journal September 2021
ABSTRACT: Starches have recently regained attention as ecofriendly barrier materials due to the increased demand for sustainable packaging. They are easily processable by conventional plastics processing equipment and have been utilized for oil and grease barrier applications. While starches have excellent oxygen barrier properties and decent water barrier properties at low relative humidity (RH), they are moisture sensitive, as demonstrated by the deterioration of the barrier properties at higher RH values. Starch esters are chemically modified starches where the hydroxyl group of the starch has been substituted by other moieties such as acetates. This imparts hydrophobicity to starches and has been claimed as a good way of retaining water vapor barrier properties of starches, even at high RH conditions. We studied the water vapor barrier properties of one class of starch esters, i.e., high amylose starch acetates that were assumed to have good water vapor barrier properties. Our investigations found that with a high degree of substitution of hydroxyl groups, the modified starches did indeed show improvements in water vapor response as compared to pure high amylose starch films; however, the barrier properties were orders of magnitude lower than commercially used water vapor barriers like polyethylene. Even though these materials had improved water vapor barrier response, high amylose starch acetates are likely unsuitable as water vapor barriers by themselves, as implied by previous literature studies and patents.
Journal articles
Magazine articles
Orifice geometry as a tool for evaluating extensional flow resistance of barrier coating colors, TAPPI Journal November 2024
ABSTRACT: Knowledge of extensional flow behavior of coating colors can be beneficial for improving runnability and eliminating defects in various coating processes. The current work evaluates the use of an orifice geometry attached to a commercial capillary viscometer as a tool to obtain extensional flow properties of barrier coating dispersions. By measuring the pressure drop across the orifice as a function of flow velocity, the method presents the flow resistance as Euler number at industrially relevant high deformation rates. The results agree with the earlier results obtained with a capillary entrance pressure loss technique. The type of polymer additive is shown to control the extensional flow resistance, with high molecular weight linear flexible polymers such as polyethylene oxide (PEO) and polyvinyl alcohol (PVOH) having highest impact. The orifice method offers advantages over other approaches, including the need for only a small sample amount, ease of measurement, and access to high deformation rates.