Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
TAPPI Journal Archive
TAPPI Journal (TJ) publishes the latest and most relevant research on the forest products and related industries. A stringent peer-review process and distinguished editorial board of academic and
Non-process elements in the lime cycle: New findings regarding NPE distribution and lime mud filterability, TAPPI Journal July 2026
ABSTRACT: Proper functioning of the recausticizing cycle is crucial for securing a stable white liquor supply for a pulp mill. Common runnability problems in the modern lime cycle, such as low filterability and poor dewatering of lime mud, high dead load, or ring formation in the lime kiln, are often caused by accumulation of non-process elements (NPEs). This project attempted to verify the traditional rules of thumb regarding the chemical behavior of NPEs: magnesium (Mg), aluminum (Al), silicon (Si), phosphorus (P), zinc (Zn), manganese (Mn), iron (Fe), copper (Cu), barium (Ba), cadmium (Cd), and lead (Pb) in the causticizing reaction, and to investigate the reasons behind poor lime mud filterability. First, a standardized method for measuring filterability of lime mud was developed. Next, a series of recausticizing experiments, followed by immediate filtration trials, was conducted using mill green liquors, laboratory-made synthetic green liquor, reburned lime/makeup mix, and extra NPE additions. It was found that sodium (Na), potassium (K), and sulfur (S) followed the liquid phase, as expected, while Mg, P, and Ba, but also Pb, Cu, and Cd, showed low solubility and accumulated in the lime mud. The Si and Al accumulated in the lime mud even though the soluble content in liquor was high, while the behavior of Mn, Fe, and Zn was more complex. Based on these results, tentative solubility limits for NPEs were suggested as a first estimate for the maximum possible concentrations of NPEs in mill white liquor. The causticization-filtration experiments revealed that overliming and high content of Mg in green liquor clearly led to lower filterability, but our addition of Si did not have such an effect. As differences in particle size and size distribution have a certain impact on the filtration resistance, the lime mud sedimentation behavior, combined with other characterization methods, might be used as an indication for the filterability. Finally, a list of recommendations for pulp mills was formulated that starts with establishing a comprehensive standard for a lime mud with good filterability. This standard can be used as a benchmark for comparison any time a lime cycle runnability problem is identified.
Controlling sulfidity by recycling sulfur in CNCG, TAPPI Journal July 2026
ABSTRACT: Pulp and paper mills have faced a major dilemma. On one hand, mills should not dispose of the side streams by mixing them with effluent water. On the other hand, there has been no other way to dispose of excess sulfur than getting rid of recovery boiler electrostatic precipitator (ESP) ash and buying sodium hydroxide to replace lost sodium. A new, yet old, process has been introduced to alleviate the problem. An alternative is the onsite production of sulfuric acid (H2SO4) to significantly reduce, or to even eliminate, the need for recovery boiler fly ash dumping. A sulfuric acid plant produces concentrated commercial quality H2SO4 from concentrated non-condensable gases (CNCGs). Up to 99.9% of the sulfur in CNCGs can be converted into concentrated sulfuric acid with this wet-gas sulfuric acid (WSA) process. There are already references on pulp mills highlighting that the process is straightforward to use. Mills can increase the amount of sulfur in CNCGs by controlling the heavy back liquor storage time and temperature. This opens up a new way to control the mill sulfidity by recycling sulfur. The effect of recycling sulfur is highlighted with reference mills. Due to integrated paper production, the Northern Mill is a large energy consumer, producing mostly softwood-based end products. The Eucalyptus Mill is a large standalone hardwood (eucalyptus) pulp mill where electricity is produced substantially in excess of its own use. As a sample case, lignin production with and without sulfur recycling is presented.
Black liquor spray properties in-furnace conditions for swirl cone nozzles TAPPI Journal July 2026
ABSTRACT: Recovery boiler furnace operation is controlled for high chemical recovery, high steam production, and low emissions. Good control allows long runs with minimum cleaning without expensive shutdowns. An essential variable affecting boiler operation is black liquor spraying into the furnace. Poorly controlled black liquor spraying causes difficulties, e.g., in chemical recovery, fouling of heat transfer surfaces, and decreased energy production. A challenging measurement strategy with three different swirl cone nozzles . types A, C, and T . was carried out at a mill in the United States. Black liquor spray properties were measured under in-furnace conditions for flow rates of 2.0 L/s to 3.0 L/s. Three spraying temperatures of 119™‹C, 122™‹C, and 126™‹C, which were 2™‹C, 5™‹C, and 9™‹C above the boiling point (ÄTe), were tested. These flow rates and temperatures are typical for industrial nozzle sizes with exit orifice sizes of 17 mm and 22 mm. An imaging method to measure droplet size in a highly challenging furnace environment was developed. Droplet volume median diameter (Dv50) for nozzles A, C, and T varied between 7 mm to 4 mm, 7 mm to 5 mm, and 8 mm to 6 mm, depending on the flow rate and temperature. The high number of droplets detected by the analysis program enabled data fitting into statistical correlations. The size and width parameters for the Rosin™] Rammer droplet size distribution function could be defined. The droplet size distribution was found to be surprisingly wide, probably because of swollen droplets. Spray velocity was measured in two locations, 5 cm from the nozzle and 1.8 m from the nozzle. Near the nozzle, the average velocity increased from 7.3 m/s to 13 m/s when the flow rate was increased from 2 L/s to 3 L/s. Increase of black liquor temperature increased spray velocity in most of the cases. At the distance of 1.8 m from the nozzle, average spray velocities varied between 4.0 m/s to 11 m/s, depending on nozzle geometry, flow rate, and temperature. The opening angles of the spray for nozzles A and C varied between 57™‹ to 78™‹. The opening angle of nozzle T with flow guide varied between 48™‹ to 56™‹. The highest penetration of the spray was estimated for nozzle T because of the narrow spray and large droplets.
Image classification of the furnace bed height in recovery boilers, TAPPI Journal July 2026
ABSTRACT: The goal of this study is to develop an approach for classifying char bed height in a recovery boiler during operation. The resulting classified images form a dataset that can be used by the mill to support operational improvements. The study integrates data from the digester, evaporation plant, recovery boiler, and recausticizing plant, along with the classified image data. A convolutional neural network (CNN) was trained on bed camera images that were manually annotated to classify furnace bed height. The model was then used to generate a binary bedheight parameter over a 16-month period, and an extreme gradient boosting (XGBoost) model was applied to identify relationships with operating parameters across the recovery cycle. The outcomes of this research may offer deeper insights into the processes underlying bed dynamics. Ultimately, the developed system may serve as a tool for optimizing bed conditions and supporting stable combustion.
Journal articles
Water and grease resistance of paperboard coated with long chain cellulose fatty acid esters using electrostatic powder coating, TAPPI Journal April 2026
ABSTRACT: Fiber-based materials used for foodservice, takeaway, and other packaging applications must typically provide water and grease resistance. Simultaneously, there is growing interest towards bio-based and renewable barrier coatings. In this study we applied thermoplastic long chain fatty acid cellulose esters onto paperboard using electrostatic powder coating to create barrier properties of interest. Electrostatic powder coating provides a water-free process to tackle moisture-induced quality issues and to provide an even coating layer. Cellulose octanoate and palmitate esters were produced in pilot scale. These were ground into fine particles using liquid nitrogen and applied onto paperboard sheets using an electrostatic powder gun. The loosely packed coatings were fixed and fused onto the paperboard by hot pressing. We characterized the coated sheets for coating thickness, contact angles with water, water absorption, grease resistance (KIT), and olive oil barrier. Two commercial polyethylene powders were used as references. Our results indicated that the long chain cellulose fatty acid ester coatings were thermoplastic and hydrophobic with contact angles above 100°. Water absorption was similar to the reference coatings. While grease resistance was lower than with the references, the cellulose ester coatings slowed down diffusion of olive oil through the paperboard. Cellulose octanoate ester with a lower melt viscosity already provided smooth coatings after the initial hot pressing step, while in most cases, the second post hot pressing step further improved the barrier properties.
Journal articles
Optimization of energy efficiency and condensate production in evaporation plants for a modern softwood pulp mill, TAPPI Journal April 2026
ABSTRACT: To meet the need to further improve thermal efficiency and environmental performance of kraft pulp mills, new systems and techniques have been developed within the evaporation plant. This paper describes these novel approaches and how they were implemented in a project completed in 2018 for a new evaporator and condensate treatment system supplied by Valmet at the SCA Östrand market pulp mill in Sweden. This project was part of a stepwise upgrade of the complete mill to increase the production capacity of the mill from 430,000 to 900,000 air-dried metric tons/year (ADt/y). As part of this upgrade, the mill had the objectives to increase the energy efficiency of the pulp mill and to minimize the air emissions as much as possible, the effluent volume, and the water usage in the mill. The mill also wanted to have the disposal of the biosludge in the black liquor, and the production of tall oil from black liquor soap, liquid methanol, and turpentine. This required that the new evaporation and condensate treatment system be very closely integrated into the other process departments of the mill, including integration of the hot weak black liquor flash vapor from the digester directly into the evaporator train and the production of multiple streams of clean evaporation plant condensate at the correct temperature for the bleach plant. Heat and mass balance calculation values, which were found to do very well in predicting the effect on actual mill operation, are also presented in this paper.
Journal articles
Editorial: Coating innovations for driving the next generation of sustainable packaging, TAPPI Journal November 2025
Welcome to the 2025 Special Coating Issue of TAPPI Journal. As we reflect on developments in 2025, the industry’s focus on sustainable packaging continues to sharpen, bringing several critical coating challenges and opportunities into view.
Journal articles
A method to produce paperboard with a lightweight low-density coating, TAPPI Journal November 2025
ABSTRACT: In this work, a method is described in which a coating layer is produced that consists of a network of bubble-shaped air-filled voids within the coating. This is accomplished by instantaneously flash-drying all the water in the coating as it exits the application nip. The nip is formed between a polished chrome drum and a deformable press roll. The combination of the drum temperature, nip pressure, and nip width allow for sufficient energy to be transferred to the coating to completely flash-dry the coating material. The pressure within the nip is sufficient to allow the coating to superheat within the nip, then flash boil as it exits the nip. This boiling effect and resulting expansion are constrained by the roll surface, resulting in a coated surface that mirrors the polished chrome surface. The coating immobilizes while in the process of boiling, which preserves the bubble structure. With a coat weight of 5 g/m2, a flat, smooth surface is produced. This process was scaled up to a mill production machine layout and run at speeds as high as 450 m/min.
Editorial: The U.S. pulp & paper industry at a crossroads: Can it lead the bioeconomy
The industry is entering a pivotal moment in which many of us find ourselves engaged in deep soul searching. Since the days of Francis Bacon when the illustrious triumvirate of gunpowder, the compass, and paper were the drivers of civilizations, our community has enjoyed a noble place at the table. Indeed, especially over the last 100 years, pulp and paper has quietly powered communication, commerce, and, more than ever today, packaging, thus representing a steady backbone for the continued stability of many global industries.