Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Committees
Collections
Journal articles
A targeted approach to produce energy-efficient packaging materials from high-yield pulp, TAPPI Journal August 2025
ABSTRACT: Unlike fossil-based plastics, wood-based packaging materials can be produced in an ecofriendly manner using wood chip residuals from sawmills and pulpwood. To produce high-yield pulp like chemithermomechanical pulps (CTMPs) for paperboard and liquid packaging, it is crucial to reduce the electric energy consumption during fiber separation. The ultimate objective is to revolutionize paperboard production by achieving a middle-layer CTMP process that consumes less than 200 kilowatt-hours per metric ton (kWh/t), significantly improving from the current 500•600 kWh/t energy demand. Optimizing the CTMP impregnation process of sodium sulfite (Na2SO3) in wood chips is crucial for achieving uniform softening, ideally at the fiber level. The properties of the fibers are significantly affected by the content of lignin sulfonates within the walls of the fiber and the middle lamellae. In this study, we employed in-house developed X-ray fluorescence (XRF) techniques, validated by beamline measurements, to map the distribution of sulfonated lignin within fibers. It also seemed possible to enhance the surface area of lignin-rich pulp fibers while losing minimal bulk by refining them with well-optimized low consistency (LC) refining. We aimed to achieve a highly efficient separation of coniferous wood fibers by co-optimizing the sulfonation and the temperature in the preheater and chip refiner. Additionally, we explored how lignin’s softening behavior and potential crosslinking influence subsequent unit operations, including pressing, peroxide bleaching, and drying, following the defibration process. In defibration during chip refining, the maximum softening of wood fibers is preferred to maximize fiber preservation and minimize energy consumption. However, optimizing the stiffness of finished pulp fibers is preferable to reduce bulk loss during paperboard production. It can strive to optimize processes to develop stronger, lighter, and more sustainable composite packaging materials. Reducing environmental impact and electric energy can help create a more sustainable future.
Journal articles
On the design of corrugated boards: A new FEM modeling and experimental validation, TAPPI Journal August 2025
ABSTRACT: This study presents a simplified finite element modeling (FEM) approach suitable for large structures made of corrugated boards, such as customized packages, based on a homogenization method, which is combined with correction factors for internal mechanisms. The homogenization process reduces computational time by transforming flute geometries into equivalent elastic models. In large deformations and in the presence of contact for a given geometry, the effective elastic modulus in the thickness direction, as well as the effective thickness of the structure, are corrected by two statistical Weibull distributions representing the contact and buckling mechanisms in a corrugated board. The Weibull parameters are obtained via experimental analysis, and such a process is then validated. The results demonstrate that the statistical parameters (â1 = 0.14, â2 = 1.31) can be used for the simplistic representation of corrugated boards, being computationally efficient. This research contributes to the optimization of corrugated packaging design, specifically by simplifying FEM models for faster, yet equally accurate, simulations.
Journal articles
Reinforcing folding boxboard ply stock with refined pulp and its effect on dewatering potential, TAPPI Journal February 2025
ABSTRACT: The folding boxboard (FBB) filler ply typically contains a significant amount of mechanical pulp such as bleached thermomechanical pulp (BTMP), bleached chemi-thermomechanical pulp (BCTMP), and chemi-thermomechanical pulp (CTMP), etc. It is usually reinforced with either refined broke from the same paper machine line and converting process or by utilizing traditional bleached kraft pulp (BKP). In response to the drive for improved/increased ply bond (to avoid undesired delamination), increased bulk, reduced basis weight, and minimized energy consumption, papermakers have experimented with various options and strategies. In between the common approaches, choices have been made between reducing the refining of the mechanical pulp, increasing the broke refining (more frequently practiced on the production scale), or increasing the BKP refining (a potentially superior choice). This study focused on a simplified approach to assess the impact of three reinforcement pulps with different refining levels on the dewatering of the filler ply. The reinforcement pulp was added to the core stock for the FBB filler ply — a mechanical pulp, BCTMP, with a drainability of 25 °SR. The proportions of the reinforcement pulp, hardwood bleached kraft pulp (HWBKP), were 20% of 30-35 °SR, 10% of HWBKP 50-55 °SR, and 5% of HWBKP 70-75 °SR. The intention behind using varying percentages of reinforcement pulp was to attain a controlled internal bond while enhancing bulk through increased mechanical pulp content. The dewatering potential of the stock mixtures was assessed at three vacuum levels — 4, 10, and 25 kPa — that can be found in progressive stages within production- scale forming sections. Our goal was to find an optimal reinforcement strategy for filler ply that would minimize the use of the reinforcement pulp, give better strength, retain bulk, and lower basis weight. The success of this strategy was verified with an actual FBB machine.
Journal articles
Comparison of the application of polysaccharide-based barrier coatings on paper using film press and spray coating, TAPPI Journal January 2025
The growing demand for sustainable packaging has spurred research into biopolymer-based solutions and their application to paper substrates. This study compares the application of low solids, high viscous aqueous solutions of alginate and chitosan on two different paper substrates using a laboratory film press coater and a purpose-built spray coating unit, with a focus on barrier performance and practical industry considerations. Key parameters investigated are air flow rate, water vapor transmission rate, and grease resistance. Results showed that due to the low solids content of the applied biopolymer solutions, film press coating required a double-layer application for coat weights exceeding 4 g/m², making it less viable for industrial application. In contrast, spray coating allowed for higher application weights in a single step. The barrier properties of spray coated samples, compared to film press coatings, varied with the paper substrate: spray coating performed better on one substrate and worse on the other. Contact angle measurement of the substrates suggested that spray coating is more suitable for a more hydrophilic substrate because of improved surface wetting. The study also identified issues with drying conditions and pinholes affecting the quality of spray coated samples, indicating a need for further research to optimize these parameters.
Journal articles
Water-based adhesive penetration into paperboard and coated paperboard, TAPPI Journal January 2025
The setting of water-based adhesives in contact with paperboard is important in the production of boxes and other packaging, but the topic has received little attention in the literature. The penetration of the adhesive into the paper surface is important to get good bond strength through mechanical interlocking. The influence of the process conditions and the paper properties on this penetration is lacking. A water-based adhesive was applied to an uncoated and coated paperboard. The coating layer had two latex levels. Samples were characterized in terms of air permeability, void fraction, average pore size, and coat weight. The adhesive was applied to the samples in a mechanical press, squeezing a drop between two samples. The penetration of the adhesive was characterized with a silicone oil absorption method that measured the decrease in pore volume after the adhesive had been applied to approximate the pore volume taken up by the adhesive. The bond strength was measured with a peeling test. The penetration depth into uncoated paper did not depend on the application method parameters such as pressing time, pressure, or initial solids of the adhesive. The penetration depth ranged from 35•40 mm. The penetration into 10 pph latex content coated paper was similar to the uncoated samples, but reduced penetration was observed into the 40 pph latex content coatings. The results were compared to the limiting amount of adhesive that was obtained from the weight gain of the samples and to a simple model that is based on flow in porous media. Peel tests revealed that good penetration was needed, as well as a strong coating layer to obtain high peel forces.
Journal articles
Effect of xylan on the mechanical performance of softwood kraft pulp 2D papers and 3D foams, TAPPI Journal March 2025
ABSTRACT: Pulp fibers are paramount in paper products and have lately seen emerging use in fiber foams. Xylan, an integral component in pulp fibers, is known to contribute to paper strength, but its effect on the strength of pulp fiber foams remains less explored. In this study, we investigate the role of xylan in both 2D handsheets and 3D foams. For a softwood kraft pulp, we enzymatically removed 1% from pulp fibers and added 3% xylan to them by adsorption, corresponding to approximately a decrease of a tenth and an increase of a third of the total xylan content. The mechanical properties of 2D fiber networks, i.e., handsheets, made using the xylan-enriched pulp improved, particularly regarding tensile strength and Young’s modulus; however, the decrease in mechanical properties of handsheets made from enzymatically- treated xylan-depleted pulp was more pronounced. In 3D networks • pulp fiber foams, much less fiber-fiber contacts formed, and thus the mechanical properties were not as much influenced by removal of xylan. Furthermore, the presence of the required surfactant on the fibers, acting as debonding agent, overshadows any positive effect xylan might have on fiber-fiber bonding. We propose that the improved mechanical properties for the sheets result from a combination of an increased number of fiber-fiber bonds and higher sheet density, while the deterioration in mechanical properties of handsheets comprising enzymatically-treated fibers is caused by the opposite effect.
Journal articles
Predictive advisory solutions for chemistry management, control, and optimization, TAPPI Journal March 2025
ABSTRACT: Process runnability and end-product quality in paper and board making are often connected to chemistry. Typically, monitoring of the chemistry status is based on a few laboratory measurements and a limited number of online specific chemistry-related measurements. Therefore, mill personnel do not have real-time transparency of the chemistry related phenomena, which can cause production instability, including deposition, higher chemical consumption, quality issues in the end-product and runnability problems. Machine learning techniques have been used to establish soft sensor models and to detect abnormalities. Furthermore, these soft sensors prove to be most useful when combined with expert-driven interpretation. This study is aimed at utilizing a hybrid solution comprising chemistry and physics models and machine learning models for stabilizing chemistry-related processes in paper and board production. The principal idea is to combine chemistry/physics models and machine learning models in a fashion close to white box modeling. A cornerstone in the approach is to formulate explanations of the findings from the models; that is, to explain in plain text what the findings mean and how operational changes can mitigate the identified risks. The approach has been demonstrated for several different applications, including deposit control in the wet end, both raw water treatment and usage, and wastewater treatment. This approach provides mill personnel with knowledge of identified phenomena and recommendations on how to stabilize chemistry-related processes. Instead of using close to black box machine learning models, a hybrid solution including chemistry/physics models can enhance the performance of artificial intelligence (AI) deployed systems. A successful way of gaining the trust from mill personnel is by creating a plain text explanation of the findings from the hybrid models. The correlation between the likelihood of a phenomena and disturbance and the explanations are derived and validated by application and chemistry and physics experts.
Journal articles
Colloidal silica and its effects during formation of paper sheets in the presence of nanofibrillated cellulose, cationic starch, and cationic acrylamide copolymer, TAPPI Journal May 2025
ABSTRACT: This work considered effects of colloidal silica addition during laboratory preparation of paper sheets containing nanofibrillated cellulose (NFC) that had been pretreated with cationic starch. The emphasis was on process performance issues, including dewatering rates, fine particle retention, and the extent of fiber flocculation. In addition, micrographs were obtained to show what was happening to the NFC upon treatments with cationic starch and subsequent application of hydrodynamic shear. Contrasting results were obtained, depending on the charge density of the cationic starch. Pretreatment of the NFC with a high charge density cationic starch (degree of substitution 0.2) resulted in strong interactions with the colloidal silica, enhancing the dewatering rate and contributing to fine-particle retention. The medium charge cationic starch pretreatment led to effects suggesting a bridging mechanism of action, and subsequent colloidal silica had no significant effect on dewatering. Treatment of that system with a high level of colloidal silica (0.2%) resulted in lower retention. In general, the final colloidal silica treatments tended to decrease the level of flocculation in the suspensions, giving more uniform handsheets. Mechanisms, some of them related to the clustering and dispersion of cationic starch-treated NFC, were proposed to account for the observed effects.
Journal articles
Magazine articles
Incorporation of post-consumer pizza boxes in the recovered fiber stream: Impacts of grease on finished product quality, TAPPI Journal March 2021
ABSTRACT: Grease and cheese contamination of used pizza boxes has led to misunderstanding and controversy about the recyclability of pizza boxes. Some collection facilities accept pizza boxes while others do not. The purpose of this study is to determine whether typical grease or cheese contamination levels associated with pizza boxes impact finished product quality. Grease (from vegetable oil) and cheese are essentially hydrophobic and in sufficiently high concentration could interfere with interfiber bonding, resulting in paper strength loss.Findings from this study will be used to determine the viability of recycling pizza boxes at current and future con-centrations in old corrugated containers (OCC) recovered fiber streams. These findings will also be used to inform the acceptability of pizza boxes in the recycle stream and educate consumers about acceptable levels of grease or cheese residue found on these recycled boxes.
Journal articles
Magazine articles
Development of converging-diverging multi-jet nozzles for molten smelt shattering in kraft recovery boilers, TAPPI Journal March 2021
ABSTRACT: The effective shattering of molten smelt is highly desired in recovery boiler systems. Ideally, shatter jet nozzle designs should: i) generate high shattering energy; ii) create a wide coverage; and iii) minimize steam consumption. This study proposes a novel converging-diverging multi-jet nozzle design to achieve these goals. A laboratory setup was established, and the nozzle performance was evaluated by generating jet pressure profiles from the measurement of a pitot tube array. The results show that the shatter jet strength is greater with a large throat diameter, high inlet pressure, and a short distance between the nozzle exit and impingement position. Increasing the number of orifices generates a wider jet coverage, and the distance between the orifices should be limited to avoid the formation of a low-pressure region between the orifices. The study also demonstrates that an optimized converging-diverging multi-jet nozzle significantly outperformed a conventional shatter jet nozzle by achieving higher energy and wider coverage while consuming less steam.